| Symptom | Trouble Area |
|---|---|
|
*1: w/ TOYOTA Parking Assist-sensor System *2: w/ Pre-collision System *3: w/ Blind Spot Monitor System *4: w/ Parking Assist Monitor System |
|
| There are ECUs or sensors that display a communication stop on the bus diagnostic screen. Or, there are ECUs or sensors that store a communication stop history on the "Detail" screen. | ·
CAN bus lines or connector ·
Central gateway ECU (network gateway ECU) ·
Clearance warning ECU assembly*1 ·
Millimeter wave radar sensor assembly*2 ·
Forward recognition camera*2 ·
Blind spot monitor sensor LH*3 ·
Television camera assembly*4 ·
No. 1 CAN junction connector ·
No. 2 CAN junction connector ·
No. 8 CAN junction connector ·
No. 3 CAN junction terminal |
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Some parts must be initialized and set when replacing or removing and installing parts.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
Operating the ignition switch, any other switches or door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Disconnect the cable from the negative (-) battery terminal.
| *a | Component with harness connected
(Central Gateway ECU [Network Gateway ECU]) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N21-23 (CA1H) - N21-8 (CA1L) | Cable disconnected from negative (-) battery terminal | Below 70 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Central Gateway ECU [Network Gateway ECU]) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N21-23 (CA1H) - N21-8 (CA1L) | Cable disconnected from negative (-) battery terminal | 54 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Central Gateway ECU [Network Gateway ECU]) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N21-23 (CA1H) - N8-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| N21-8 (CA1L) - N8-16 (BAT) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Central Gateway ECU [Network Gateway ECU]) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N21-23 (CA1H) - N8-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| N21-8 (CA1L) - N8-4 (CG) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU]) |
| *b | Front view of DLC3 |
Disconnect the N21 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N21-23 (CA1H) - N8-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| N21-8 (CA1L) - N8-4 (CG) |
Reconnect the N21 central gateway ECU (network gateway ECU) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Terminal) |
| *b | Front view of DLC3 |
Disconnect the Z24 No. 3 CAN junction terminal connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z24-3 (CANH) - N8-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Z24-2 (CANL) - N8-4 (CG) |
Reconnect the Z24 No. 3 CAN junction terminal connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N104 No. 1 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 1 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | Front view of DLC3 |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
| N104 | G | W | Central gateway ECU (network gateway ECU) |
| N105 | GR | W | No. 2 CAN junction connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N104-1 (CANH) - N8-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| N104-2 (CANL) - N8-4 (CG) |
Reconnect the N104 No. 1 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N105 No. 1 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 1 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | Front view of DLC3 |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
| N104 | G | W | Central gateway ECU (network gateway ECU) |
| N105 | GR | W | No. 2 CAN junction connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N105-1 (CANH) - N8-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| N105-2 (CANL) - N8-4 (CG) |
Reconnect the N105 No. 1 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N107 No. 2 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 2 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 2 CAN Junction Connector) |
*b | Front view of DLC3 |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*1: w/ Pre-collision System *2: w/ TOYOTA Parking Assist-sensor System |
|||
| N107 | GR | W | No. 1 CAN junction connector |
| N108 | P | W | No. 8 CAN junction connector |
| N109 | R | W | Millimeter wave radar sensor assembly*1 |
| N110 | V | W | Forward recognition camera*1 |
| N111 | L | W | Clearance warning ECU assembly*2 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N107-1 (CANH) - N8-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| N107-2 (CANL) - N8-4 (CG) |
Reconnect the N107 No. 2 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Pre-collision System | A |
| w/o Pre-collision System | B |
A
B
Disconnect the N109 No. 2 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 2 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 2 CAN Junction Connector) |
*b | Front view of DLC3 |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*: w/ TOYOTA Parking Assist-sensor System |
|||
| N107 | GR | W | No. 1 CAN junction connector |
| N108 | P | W | No. 8 CAN junction connector |
| N109 | R | W | Millimeter wave radar sensor assembly |
| N110 | V | W | Forward recognition camera |
| N111 | L | W | Clearance warning ECU assembly* |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N109-1 (CANH) - N8-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| N109-2 (CANL) - N8-4 (CG) |
Reconnect the N109 No. 2 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N110 No. 2 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 2 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 2 CAN Junction Connector) |
*b | Front view of DLC3 |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*: w/ TOYOTA Parking Assist-sensor System |
|||
| N107 | GR | W | No. 1 CAN junction connector |
| N108 | P | W | No. 8 CAN junction connector |
| N109 | R | W | Millimeter wave radar sensor assembly |
| N110 | V | W | Forward recognition camera |
| N111 | L | W | Clearance warning ECU assembly* |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N110-1 (CANH) - N8-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| N110-2 (CANL) - N8-4 (CG) |
Reconnect the N110 No. 2 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ TOYOTA Parking Assist-sensor System | A |
| w/o TOYOTA Parking Assist-sensor System | B |
A
B
Disconnect the N111 No. 2 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 2 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 2 CAN Junction Connector) |
*b | Front view of DLC3 |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*: w/ Pre-collision System |
|||
| N107 | GR | W | No. 1 CAN junction connector |
| N108 | P | W | No. 8 CAN junction connector |
| N109 | R | W | Millimeter wave radar sensor assembly* |
| N110 | V | W | Forward recognition camera* |
| N111 | L | W | Clearance warning ECU assembly |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N111-1 (CANH) - N8-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| N111-2 (CANL) - N8-4 (CG) |
Reconnect the N111 No. 2 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N108 No. 2 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 2 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 2 CAN Junction Connector) |
*b | Front view of DLC3 |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*1: w/ Pre-collision System *2: w/ TOYOTA Parking Assist-sensor System |
|||
| N107 | GR | W | No. 1 CAN junction connector |
| N108 | P | W | No. 8 CAN junction connector |
| N109 | R | W | Millimeter wave radar sensor assembly*1 |
| N110 | V | W | Forward recognition camera*1 |
| N111 | L | W | Clearance warning ECU assembly*2 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N108-1 (CANH) - N8-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| N108-2 (CANL) - N8-4 (CG) |
Reconnect the N108 No. 2 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Z20 No. 8 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 8 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 8 CAN Junction Connector) |
*b | Front view of DLC3 |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*1: w/ Blind Spot Monitor System *2: w/ Parking Assist Monitor System |
|||
| Z20 | P | W | No. 2 CAN junction connector |
| Z21 | B | W | No. 3 CAN junction terminal |
| Z22 | BE | W | Blind spot monitor sensor LH*1 |
| Z23 | L | W | Television camera assembly*2 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z20-1 (CANH) - N8-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Z20-2 (CANL) - N8-4 (CG) |
Reconnect the Z20 No. 8 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Blind Spot Monitor System | A |
| w/o Blind Spot Monitor System | B |
A
B
Disconnect the Z22 No. 8 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 8 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 8 CAN Junction Connector) |
*b | Front view of DLC3 |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*: w/ Parking Assist Monitor System |
|||
| Z20 | P | W | No. 2 CAN junction connector |
| Z21 | B | W | No. 3 CAN junction terminal |
| Z22 | BE | W | Blind spot monitor sensor LH |
| Z23 | L | W | Television camera assembly* |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z22-1 (CANH) - N8-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Z22-2 (CANL) - N8-4 (CG) |
Reconnect the Z22 No. 8 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Parking Assist Monitor System | A |
| w/o Parking Assist Monitor System | B |
A
B
Disconnect the Z23 No. 8 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 8 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 8 CAN Junction Connector) |
*b | Front view of DLC3 |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*: w/ Blind Spot Monitor System |
|||
| Z20 | P | W | No. 2 CAN junction connector |
| Z21 | B | W | No. 3 CAN junction terminal |
| Z22 | BE | W | Blind spot monitor sensor LH* |
| Z23 | L | W | Television camera assembly |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z23-1 (CANH) - N8-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Z23-2 (CANL) - N8-4 (CG) |
Reconnect the Z23 No. 8 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Z21 No. 8 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 8 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 8 CAN Junction Connector) |
*b | Front view of DLC3 |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*1: w/ Blind Spot Monitor System *2: w/ Parking Assist Monitor System |
|||
| Z20 | P | W | No. 2 CAN junction connector |
| Z21 | B | W | No. 3 CAN junction terminal |
| Z22 | BE | W | Blind spot monitor sensor LH*1 |
| Z23 | L | W | Television camera assembly*2 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z21-1 (CANH) - N8-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Z21-2 (CANL) - N8-4 (CG) |
Reconnect the Z21 No. 8 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A3 millimeter wave radar sensor assembly connector.
| *a | Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A3-3 (CA2H) - N8-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A3-2 (CA2L) - N8-4 (CG) |
Reconnect the A3 millimeter wave radar sensor assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the a9 forward recognition camera connector.
| *a | Front view of wire harness connector
(to Forward Recognition Camera) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a9-5 (CA1P) - N8-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| a9-11 (CA1N) - N8-4 (CG) |
Reconnect the a9 forward recognition camera connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N48 clearance warning ECU assembly connector.
| *a | Front view of wire harness connector
(to Clearance Warning ECU Assembly) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N48-17 (R1) - N8-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| N48-18 (R2) - N8-4 (CG) |
Reconnect the N48 clearance warning ECU assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the e2 blind spot monitor sensor LH connector.
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e2-2 (CA1P) - N8-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| e2-7 (CA1N) - N8-4 (CG) |
Reconnect the e2 blind spot monitor sensor LH connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the i7 television camera assembly connector.
| *a | Front view of wire harness connector
(to Television Camera Assembly) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| i7-4 (CANH) - N8-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| i7-1 (CANL) - N8-4 (CG) |
Reconnect the i7 television camera assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU]) |
| *b | Front view of DLC3 |
Disconnect the N21 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N21-23 (CA1H) - N8-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| N21-8 (CA1L) - N8-16 (BAT) |
Reconnect the N21 central gateway ECU (network gateway ECU) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Terminal) |
| *b | Front view of DLC3 |
Disconnect the Z24 No. 3 CAN junction terminal connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z24-3 (CANH) - N8-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Z24-2 (CANL) - N8-16 (BAT) |
Reconnect the Z24 No. 3 CAN junction terminal connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N104 No. 1 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 1 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | Front view of DLC3 |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
| N104 | G | W | Central gateway ECU (network gateway ECU) |
| N105 | GR | W | No. 2 CAN junction connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N104-1 (CANH) - N8-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| N104-2 (CANL) - N8-16 (BAT) |
Reconnect the N104 No. 1 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N105 No. 1 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 1 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | Front view of DLC3 |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
| N104 | G | W | Central gateway ECU (network gateway ECU) |
| N105 | GR | W | No. 2 CAN junction connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N105-1 (CANH) - N8-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| N105-2 (CANL) - N8-16 (BAT) |
Reconnect the N105 No. 1 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N107 No. 2 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 2 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 2 CAN Junction Connector) |
*b | Front view of DLC3 |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*1: w/ Pre-collision System *2: w/ TOYOTA Parking Assist-sensor System |
|||
| N107 | GR | W | No. 1 CAN junction connector |
| N108 | P | W | No. 8 CAN junction connector |
| N109 | R | W | Millimeter wave radar sensor assembly*1 |
| N110 | V | W | Forward recognition camera*1 |
| N111 | L | W | Clearance warning ECU assembly*2 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N107-1 (CANH) - N8-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| N107-2 (CANL) - N8-16 (BAT) |
Reconnect the N107 No. 2 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Pre-collision System | A |
| w/o Pre-collision System | B |
A
B
Disconnect the N109 No. 2 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 2 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 2 CAN Junction Connector) |
*b | Front view of DLC3 |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*: w/ TOYOTA Parking Assist-sensor System |
|||
| N107 | GR | W | No. 1 CAN junction connector |
| N108 | P | W | No. 8 CAN junction connector |
| N109 | R | W | Millimeter wave radar sensor assembly |
| N110 | V | W | Forward recognition camera |
| N111 | L | W | Clearance warning ECU assembly* |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N109-1 (CANH) - N8-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| N109-2 (CANL) - N8-16 (BAT) |
Reconnect the N109 No. 2 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N110 No. 2 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 2 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 2 CAN Junction Connector) |
*b | Front view of DLC3 |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*: w/ TOYOTA Parking Assist-sensor System |
|||
| N107 | GR | W | No. 1 CAN junction connector |
| N108 | P | W | No. 8 CAN junction connector |
| N109 | R | W | Millimeter wave radar sensor assembly |
| N110 | V | W | Forward recognition camera |
| N111 | L | W | Clearance warning ECU assembly* |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N110-1 (CANH) - N8-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| N110-2 (CANL) - N8-16 (BAT) |
Reconnect the N110 No. 2 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ TOYOTA Parking Assist-sensor System | A |
| w/o TOYOTA Parking Assist-sensor System | B |
A
B
Disconnect the N111 No. 2 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 2 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 2 CAN Junction Connector) |
*b | Front view of DLC3 |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*: w/ Pre-collision System |
|||
| N107 | GR | W | No. 1 CAN junction connector |
| N108 | P | W | No. 8 CAN junction connector |
| N109 | R | W | Millimeter wave radar sensor assembly* |
| N110 | V | W | Forward recognition camera* |
| N111 | L | W | Clearance warning ECU assembly |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N111-1 (CANH) - N8-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| N111-2 (CANL) - N8-16 (BAT) |
Reconnect the N111 No. 2 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N108 No. 2 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 2 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 2 CAN Junction Connector) |
*b | Front view of DLC3 |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*1: w/ Pre-collision System *2: w/ TOYOTA Parking Assist-sensor System |
|||
| N107 | GR | W | No. 1 CAN junction connector |
| N108 | P | W | No. 8 CAN junction connector |
| N109 | R | W | Millimeter wave radar sensor assembly*1 |
| N110 | V | W | Forward recognition camera*1 |
| N111 | L | W | Clearance warning ECU assembly*2 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N108-1 (CANH) - N8-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| N108-2 (CANL) - N8-16 (BAT) |
Reconnect the N108 No. 2 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Z20 No. 8 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 8 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 8 CAN Junction Connector) |
*b | Front view of DLC3 |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*1: w/ Blind Spot Monitor System *2: w/ Parking Assist Monitor System |
|||
| Z20 | P | W | No. 2 CAN junction connector |
| Z21 | B | W | No. 3 CAN junction terminal |
| Z22 | BE | W | Blind spot monitor sensor LH*1 |
| Z23 | L | W | Television camera assembly*2 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z20-1 (CANH) - N8-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Z20-2 (CANL) - N8-16 (BAT) |
Reconnect the Z20 No. 8 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Blind Spot Monitor System | A |
| w/o Blind Spot Monitor System | B |
A
B
Disconnect the Z22 No. 8 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 8 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 8 CAN Junction Connector) |
*b | Front view of DLC3 |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*: w/ Parking Assist Monitor System |
|||
| Z20 | P | W | No. 2 CAN junction connector |
| Z21 | B | W | No. 3 CAN junction terminal |
| Z22 | BE | W | Blind spot monitor sensor LH |
| Z23 | L | W | Television camera assembly* |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z22-1 (CANH) - N8-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Z22-2 (CANL) - N8-16 (BAT) |
Reconnect the Z22 No. 8 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Parking Assist Monitor System | A |
| w/o Parking Assist Monitor System | B |
A
B
Disconnect the Z23 No. 8 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 8 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 8 CAN Junction Connector) |
*b | Front view of DLC3 |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*: w/ Blind Spot Monitor System |
|||
| Z20 | P | W | No. 2 CAN junction connector |
| Z21 | B | W | No. 3 CAN junction terminal |
| Z22 | BE | W | Blind spot monitor sensor LH* |
| Z23 | L | W | Television camera assembly |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z23-1 (CANH) - N8-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Z23-2 (CANL) - N8-16 (BAT) |
Reconnect the Z23 No. 8 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Z21 No. 8 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 8 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 8 CAN Junction Connector) |
*b | Front view of DLC3 |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*1: w/ Blind Spot Monitor System *2: w/ Parking Assist Monitor System |
|||
| Z20 | P | W | No. 2 CAN junction connector |
| Z21 | B | W | No. 3 CAN junction terminal |
| Z22 | BE | W | Blind spot monitor sensor LH*1 |
| Z23 | L | W | Television camera assembly*2 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z21-1 (CANH) - N8-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Z21-2 (CANL) - N8-16 (BAT) |
Reconnect the Z21 No. 8 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A3 millimeter wave radar sensor assembly connector.
| *a | Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A3-3 (CA2H) - N8-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A3-2 (CA2L) - N8-16 (BAT) |
Reconnect the A3 millimeter wave radar sensor assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the a9 forward recognition camera connector.
| *a | Front view of wire harness connector
(to Forward Recognition Camera) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a9-5 (CA1P) - N8-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| a9-11 (CA1N) - N8-16 (BAT) |
Reconnect the a9 forward recognition camera connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N48 clearance warning ECU assembly connector.
| *a | Front view of wire harness connector
(to Clearance Warning ECU Assembly) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N48-17 (R1) - N8-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| N48-18 (R2) - N8-16 (BAT) |
Reconnect the N48 clearance warning ECU assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the e2 blind spot monitor sensor LH connector.
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e2-2 (CA1P) - N8-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| e2-7 (CA1N) - N8-16 (BAT) |
Reconnect the e2 blind spot monitor sensor LH connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the i7 television camera assembly connector.
| *a | Front view of wire harness connector
(to Television Camera Assembly) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| i7-4 (CANH) - N8-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| i7-1 (CANL) - N8-16 (BAT) |
Reconnect the i7 television camera assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU]) |
Disconnect the N21 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N21-23 (CA1H) - N21-8 (CA1L) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
Reconnect the N21 central gateway ECU (network gateway ECU) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Terminal) |
Disconnect the Z24 No. 3 CAN junction terminal connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z24-3 (CANH) - Z24-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
Reconnect the Z24 No. 3 CAN junction terminal connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N104 No. 1 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 1 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 1 CAN Junction Connector) |
- | - |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
| N104 | G | W | Central gateway ECU (network gateway ECU) |
| N105 | GR | W | No. 2 CAN junction connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N104-1 (CANH) - N104-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
Reconnect the N104 No. 1 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N105 No. 1 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 1 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 1 CAN Junction Connector) |
- | - |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
| N104 | G | W | Central gateway ECU (network gateway ECU) |
| N105 | GR | W | No. 2 CAN junction connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N105-1 (CANH) - N105-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
Reconnect the N105 No. 1 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N107 No. 2 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 2 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 2 CAN Junction Connector) |
- | - |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*1: w/ Pre-collision System *2: w/ TOYOTA Parking Assist-sensor System |
|||
| N107 | GR | W | No. 1 CAN junction connector |
| N108 | P | W | No. 8 CAN junction connector |
| N109 | R | W | Millimeter wave radar sensor assembly*1 |
| N110 | V | W | Forward recognition camera*1 |
| N111 | L | W | Clearance warning ECU assembly*2 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N107-1 (CANH) - N107-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
Reconnect the N107 No. 2 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Pre-collision System | A |
| w/o Pre-collision System | B |
A
B
Disconnect the N109 No. 2 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 2 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 2 CAN Junction Connector) |
- | - |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*: w/ TOYOTA Parking Assist-sensor System |
|||
| N107 | GR | W | No. 1 CAN junction connector |
| N108 | P | W | No. 8 CAN junction connector |
| N109 | R | W | Millimeter wave radar sensor assembly |
| N110 | V | W | Forward recognition camera |
| N111 | L | W | Clearance warning ECU assembly* |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N109-1 (CANH) - N109-2 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
Reconnect the N109 No. 2 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N110 No. 2 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 2 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 2 CAN Junction Connector) |
- | - |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*: w/ TOYOTA Parking Assist-sensor System |
|||
| N107 | GR | W | No. 1 CAN junction connector |
| N108 | P | W | No. 8 CAN junction connector |
| N109 | R | W | Millimeter wave radar sensor assembly |
| N110 | V | W | Forward recognition camera |
| N111 | L | W | Clearance warning ECU assembly* |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N110-1 (CANH) - N110-2 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
Reconnect the N110 No. 2 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ TOYOTA Parking Assist-sensor System | A |
| w/o TOYOTA Parking Assist-sensor System | B |
A
B
Disconnect the N111 No. 2 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 2 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 2 CAN Junction Connector) |
- | - |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*1: w/ Pre-collision System *2: w/ TOYOTA Parking Assist-sensor System |
|||
| N107 | GR | W | No. 1 CAN junction connector |
| N108 | P | W | No. 8 CAN junction connector |
| N109 | R | W | Millimeter wave radar sensor assembly*1 |
| N110 | V | W | Forward recognition camera*1 |
| N111 | L | W | Clearance warning ECU assembly*2 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N111-1 (CANH) - N111-2 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
Reconnect the N111 No. 2 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N108 No. 2 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 2 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 2 CAN Junction Connector) |
- | - |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*1: w/ Pre-collision System *2: w/ TOYOTA Parking Assist-sensor System |
|||
| N107 | GR | W | No. 1 CAN junction connector |
| N108 | P | W | No. 8 CAN junction connector |
| N109 | R | W | Millimeter wave radar sensor assembly*1 |
| N110 | V | W | Forward recognition camera*1 |
| N111 | L | W | Clearance warning ECU assembly*2 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N108-1 (CANH) - N108-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
Reconnect the N108 No. 2 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Z20 No. 8 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 8 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 8 CAN Junction Connector) |
- | - |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*1: w/ Blind Spot Monitor System *2: w/ Parking Assist Monitor System |
|||
| Z20 | P | W | No. 2 CAN junction connector |
| Z21 | B | W | No. 3 CAN junction terminal |
| Z22 | BE | W | Blind spot monitor sensor LH*1 |
| Z23 | L | W | Television camera assembly*2 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z20-1 (CANH) - Z20-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
Reconnect the Z20 No. 8 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Blind Spot Monitor System | A |
| w/o Blind Spot Monitor System | B |
A
B
Disconnect the Z22 No. 8 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 8 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 8 CAN Junction Connector) |
- | - |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*: w/ Parking Assist Monitor System |
|||
| Z20 | P | W | No. 2 CAN junction connector |
| Z21 | B | W | No. 3 CAN junction terminal |
| Z22 | BE | W | Blind spot monitor sensor LH |
| Z23 | L | W | Television camera assembly* |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z22-1 (CANH) - Z22-2 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
Reconnect the Z22 No. 8 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Parking Assist Monitor System | A |
| w/o Parking Assist Monitor System | B |
A
B
Disconnect the Z23 No. 8 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 8 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 8 CAN Junction Connector) |
- | - |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*: w/ Blind Spot Monitor System |
|||
| Z20 | P | W | No. 2 CAN junction connector |
| Z21 | B | W | No. 3 CAN junction terminal |
| Z22 | BE | W | Blind spot monitor sensor LH* |
| Z23 | L | W | Television camera assembly |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z23-1 (CANH) - Z23-2 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
Reconnect the Z23 No. 8 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Z21 No. 8 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 8 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 8 CAN Junction Connector) |
- | - |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*1: w/ Blind Spot Monitor System *2: w/ Parking Assist Monitor System |
|||
| Z20 | P | W | No. 2 CAN junction connector |
| Z21 | B | W | No. 3 CAN junction terminal |
| Z22 | BE | W | Blind spot monitor sensor LH*1 |
| Z23 | L | W | Television camera assembly*2 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z21-1 (CANH) - Z21-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
Reconnect the Z21 No. 8 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly) |
Disconnect the A3 millimeter wave radar sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A3-3 (CA2H) - A3-2 (CA2L) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
Reconnect the A3 millimeter wave radar sensor assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Forward Recognition Camera) |
Disconnect the a9 forward recognition camera connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a9-5 (CA1P) - a9-11 (CA1N) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
Reconnect the a9 forward recognition camera connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Clearance Warning ECU Assembly) |
Disconnect the N48 clearance warning ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N48-17 (R1) - N48-18 (R2) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
Reconnect the N48 clearance warning ECU assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH) |
Disconnect the e2 blind spot monitor sensor LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e2-2 (CA1P) - e2-7 (CA1N) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
Reconnect the e2 blind spot monitor sensor LH connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Television Camera Assembly) |
Disconnect the i7 television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| i7-4 (CANH) - i7-1 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
Reconnect the i7 television camera assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU]) |
Disconnect the N21 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N21-23 (CA1H) - N21-8 (CA1L) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
Reconnect the N21 central gateway ECU (network gateway ECU) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Terminal) |
Disconnect the Z24 No. 3 CAN junction terminal connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z24-3 (CANH) - Z24-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
Reconnect the Z24 No. 3 CAN junction terminal connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N104 No. 1 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 1 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 1 CAN Junction Connector) |
- | - |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
| N104 | G | W | Central gateway ECU (network gateway ECU) |
| N105 | GR | W | No. 2 CAN junction connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N104-1 (CANH) - N104-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
Reconnect the N104 No. 1 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N105 No. 1 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 1 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 1 CAN Junction Connector) |
- | - |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
| N104 | G | W | Central gateway ECU (network gateway ECU) |
| N105 | GR | W | No. 2 CAN junction connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N105-1 (CANH) - N105-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
Reconnect the N105 No. 1 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N107 No. 2 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 2 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 2 CAN Junction Connector) |
- | - |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*1: w/ Pre-collision System *2: w/ TOYOTA Parking Assist-sensor System |
|||
| N107 | GR | W | No. 1 CAN junction connector |
| N108 | P | W | No. 8 CAN junction connector |
| N109 | R | W | Millimeter wave radar sensor assembly*1 |
| N110 | V | W | Forward recognition camera*1 |
| N111 | L | W | Clearance warning ECU assembly*2 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N107-1 (CANH) - N107-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
Reconnect the N107 No. 2 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N108 No. 2 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 2 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 2 CAN Junction Connector) |
- | - |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*1: w/ Pre-collision System *2: w/ TOYOTA Parking Assist-sensor System |
|||
| N107 | GR | W | No. 1 CAN junction connector |
| N108 | P | W | No. 8 CAN junction connector |
| N109 | R | W | Millimeter wave radar sensor assembly*1 |
| N110 | V | W | Forward recognition camera*1 |
| N111 | L | W | Clearance warning ECU assembly*2 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N108-1 (CANH) - N108-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
Reconnect the N108 No. 2 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Z20 No. 8 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 8 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 8 CAN Junction Connector) |
- | - |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*1: w/ Blind Spot Monitor System *2: w/ Parking Assist Monitor System |
|||
| Z20 | P | W | No. 2 CAN junction connector |
| Z21 | B | W | No. 3 CAN junction terminal |
| Z22 | BE | W | Blind spot monitor sensor LH*1 |
| Z23 | L | W | Television camera assembly*2 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z20-1 (CANH) - Z20-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
Reconnect the Z20 No. 8 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Z21 No. 8 CAN junction connector.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | No. 8 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 8 CAN Junction Connector) |
- | - |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*1: w/ Blind Spot Monitor System *2: w/ Parking Assist Monitor System |
|||
| Z20 | P | W | No. 2 CAN junction connector |
| Z21 | B | W | No. 3 CAN junction terminal |
| Z22 | BE | W | Blind spot monitor sensor LH*1 |
| Z23 | L | W | Television camera assembly*2 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z21-1 (CANH) - Z21-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
Reconnect the Z21 No. 8 CAN junction connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG