2007-2013 Highlander Kluger · Service Manual BRAKE

Brake Warning Light Remains ON

Circuit diagnosis · Vehicles built Jul 2010 – Jun 2012

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jun 2012 from Jul 2012

DESCRIPTION

The skid control ECU is connected to the combination meter via CAN communication.
If any of the following is detected, the brake warning light remains on:
  1. The skid control ECU connector is disconnected from the skid control ECU.
  2. The brake fluid level is insufficient.
  3. The parking brake is applied.
  4. EBD operation has been disabled.

HINT:
For vehicles with the multi-information display, the master caution indicator light will come on and a brake malfunction message will be displayed on the multi-information display if the EBD system is malfunctioning.


WIRING DIAGRAM

C171171E02

INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (Click here).


1. CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication system DTC is output (Click here).

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
INSPECT CAN COMMUNICATION SYSTEM (Click here)
A


2. CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
  1. Check if the skid control ECU connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


3. CHECK BATTERY
  1. Check the battery voltage.

    Standard voltage:
    11 to 14 V



NG
CHECK OR REPLACE CHARGING SYSTEM OR BATTERY (for 2GR-FE) (Click here)
OK


4. INSPECT SKID CONTROL ECU (IG1 TERMINAL)

  1. C160263E43
    Disconnect the skid control ECU connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A24-34 (IG1) - Body ground
    Ignition switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)
OK


5. INSPECT SKID CONTROL ECU (GND1 TERMINAL)

  1. C160263E41
    Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A24-1 (GND1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)
OK


6. READ VALUE ON INTELLIGENT TESTER (PARKING BRAKE SWITCH)
  1. Reconnect the skid control ECU connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Select the Data List mode on the intelligent tester (Click here).

    ABS / VSC / TRC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Parking Brake SW
    Parking brake switch / ON or OFF
    ON: Parking brake applied
    OFF: Parking brake released
    -

  1. Using the intelligent tester, check the switch condition on the intelligent tester changes according to parking brake pedal operation.

    OK:
    The intelligent tester displays ON or OFF according to parking brake pedal operation.



NG
Go to step 10
OK


7. INSPECT BRAKE FLUID LEVEL WARNING SWITCH

  1. C156508E01
    Turn the ignition switch off.

  1. Remove the reservoir filler cap and strainer.

  1. Disconnect the brake fluid level warning switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    A float is located inside the reservoir. Its position can be changed by increasing or decreasing the level of brake fluid.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (+) - 2 (E)
    Brake fluid level warning switch OFF (Float up)
    1.9 to 2.1 kΩ
    1 (+) - 2 (E)
    Brake fluid level warning switch ON (Float down)
    Below 1 Ω

    HINT:
    If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.



NG
REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (BRAKE FLUID LEVEL WARNING SWITCH) (Click here)
OK


8. CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE FLUID LEVEL WARNING SWITCH)

  1. C158617E08
    Disconnect the combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E1-28 (B/LE) - A22-1 (+)
    Always
    Below 1 Ω
    E1-28 (B/LE) - Body ground
    Always
    10 kΩ or higher
    A22-2 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. INSPECT COMBINATION METER ASSEMBLY
  1. Perform the Active Test of the combination meter (meter CPU) using the intelligent tester (Click here).

  1. Check the combination meter.

    HINT:
    Reinstall the connectors and restore the vehicle to its prior condition before checking the combination meter.

    OK:
    The brake warning light turns on or off in accordance with the intelligent tester operation.

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (Click here).



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

10. INSPECT PARKING BRAKE SWITCH

  1. C167308E01
    Turn the ignition switch off.

  1. Disconnect the parking brake switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Parking brake switch ON
    (Switch pin free)
    Below 1 Ω
    1 - Body ground
    Parking brake switch OFF
    (Switch pin pushed in)
    10 kΩ or higher



NG
REPLACE PARKING BRAKE SWITCH (Click here)
OK


11. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - PARKING BRAKE SWITCH)

  1. C167309E03
    Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A24-29 (PKB) - A18-1
    Always
    Below 1 Ω
    A24-29 (PKB) - Body ground
    Always
    10 kΩ or higher

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)


← Brake Warning Light Remains ON (Aug 2008 – Jun 2010)Brake Warning Light Remains ON (from Jul 2012) →