DTC C1425 Open in Stop Light Switch Circuit |
| DTC Code | DTC Detection Condition | Trouble Area |
| C1425 | When IG1 terminal voltage is between 9.5 and 17.4 V, an open stop light switch circuit continues for 3 seconds or more. |
|


| 1.CHECK STOP LIGHT OPERATION |
Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.
| Condition | Illumination Condition |
| Brake pedal depressed | ON |
| Brake pedal released | OFF |
|
| ||||
| OK | |
| 2.READ VALUE ON TECHSTREAM (STOP LIGHT SWITCH) |
Connect Techstream to the DLC3.
Turn the ignition switch on (IG).
Select the Data List mode on Techstream (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Stop Light SW | Stop light switch / ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released | - |
Check that the stop light switch display observed on Techstream changes according to brake pedal operation.
|
| ||||
| OK | |
| 3.RECONFIRM DTC |
Turn the ignition switch off.
Clear the DTCs (Click here).
Start the engine.
Depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is recorded (Click here).
| Result | Proceed to |
| DTC (C1425) is not output | A |
| DTC (C1425) is output | B |
|
| ||||
| A | ||
| ||
| 4.INSPECT STOP FUSE |
![]() |
Remove the STOP fuse from the main body ECU (instrument panel junction block).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| STOP (10 A) fuse | Always | Below 1 Ω |
|
| ||||
| OK | |
| 5.INSPECT STOP LIGHT SWITCH (POWER SOURCE TERMINAL) |
![]() |
Install the STOP fuse.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the stop light switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A19-2 - Body ground | Always | 11 to 14 V |
|
| ||||
| OK | |
| 6.INSPECT STOP LIGHT SWITCH |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 - 2 | Switch pin free | Below 1 Ω |
| 1 - 2 | Switch pin pushed in | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.INSPECT STOP LIGHT CONTROL RELAY |
![]() |
Remove the stop light control relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 4 | Voltage is not applied between terminals 1 and 2 | Below 1 Ω |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ENGINE ROOM RELAY BLOCK) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A19-1 - Stop light control relay terminal 4 | Always | Below 1 Ω |
| A19-1 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ENGINE ROOM RELAY BLOCK) |
![]() |
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A24-2 (STP) - Stop light control relay terminal 3 | Always | Below 1 Ω |
|
| ||||
| OK | |
| 10.RECONFIRM DTC |
Clear the DTCs (Click here).
Start the engine.
Depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is recorded (Click here).
| Result | Proceed to |
| DTC (C1425) is not output | A |
| DTC (C1425) is output | B |
|
| ||||
| A | ||
| ||
| 11.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ENGINE ROOM RELAY BLOCK) |
![]() |
Turn the ignition switch off.
Remove the stop light control relay.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A24-2 (STP) - Stop light control relay terminal 3 | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||