Home › BRAKE › BRAKE CONTROL › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C1249/49    Open in Stop Light Switch Circuit

for Preparation Click here


DESCRIPTION

The skid control ECU inputs the stop light switch signal and detects the brake pedal operation status.
The skid control ECU has an open detection circuit, which outputs this DTC if it detects an open in the stop light input line or ground line of the stop light circuit with the stop light switch off (brake pedal not depressed).

DTC Code
INF Code
DTC Detection Condition
Trouble Area
C1249/49
520
When IG1 terminal voltage is between 9.5 and 17.2 V, an open stop light switch circuit continues for 10 seconds or more.
  1. STOP fuse
  2. Stop light switch
  3. Stop light switch circuit
  4. Stop light control relay
  5. Stop light control relay circuit
  6. Skid control ECU

WIRING DIAGRAM


C173876E01


C173877E01


INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU, perform initialization and calibration of the linear solenoid valve (Click here).

1.CHECK STOP LIGHT OPERATION
  1. Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

    OK:

    Condition
    Illumination Condition
    Brake pedal depressed
    ON
    Brake pedal released
    OFF



NG
Go to step 6
OK


2.READ VALUE USING TECHSTREAM (STOP LIGHT SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the Data List mode on the Techstream (Click here).

    ABS / VSC / TRAC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

  1. Check that the stop light switch display observed on the Techstream changes according to brake pedal operation.

    OK:
    The Techstream displays ON or OFF according to brake pedal operation.



NG
Go to step 13
OK


3.INSPECT SKID CONTROL ECU (IG1 TERMINAL)
C173879E01
  1. Turn the power switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A44-7 (IG1) - Body ground
    Power switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)
OK


4.INSPECT SKID CONTROL ECU (GND TERMINAL)
  1. Turn the power switch off.


C173862E01

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the skid control ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A46-1 (GND1) - Body ground
    Always
    Below 1 Ω
    A44-2 (GND2) - Body ground
    Always
    Below 1 Ω
    A44-1 (GND3) - Body ground
    Always
    Below 1 Ω
    A47-2 (GND4) - Body ground
    Always
    Below 1 Ω
    A47-1 (GND5) - Body ground
    Always
    Below 1 Ω
    A45-4 (GND6) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


5.RECONFIRM DTC
  1. Reconnect the skid control ECU connectors.

  1. Clear the DTCs (Click here).

  1. Turn the power switch on (READY).

  1. Depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is recorded (Click here).

    Result:

    Result
    Proceed to
    DTC (C1249/49) is not output
    A
    DTC (C1249/49) is output
    B

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE SKID CONTROL ECU (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)  

6.INSPECT STOP FUSE
C175271E01
  1. Remove the STOP fuse from the main body ECU (instrument panel junction block).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    STOP (10 A) fuse
    Always
    Below 1 Ω



NG
REPLACE STOP FUSE
OK


7.INSPECT STOP LIGHT SWITCH (POWER SOURCE TERMINAL)
C173882E01
  1. Install the STOP fuse.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the stop light switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A19-2 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


8.INSPECT STOP LIGHT SWITCH


    C147842E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Switch pin free
    Below 1 Ω
    1 - 2
    Switch pin pushed in
    10 kΩ or higher



NG
REPLACE STOP LIGHT SWITCH (Click here)
OK


9.INSPECT STOP LIGHT CONTROL RELAY


    C126459E06
  1. Remove the stop light control relay.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 4
    Voltage is not applied between terminals 1 and 2
    Below 1 Ω



NG
REPLACE STOP LIGHT CONTROL RELAY
OK


10.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ENGINE ROOM RELAY BLOCK)


    C168479E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A19-1 - Stop light control relay terminal 4
    Always
    Below 1 Ω
    A19-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ENGINE ROOM RELAY BLOCK)
C175139E01
  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A47-24 (EXI) - Stop light control relay terminal 3
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the power switch on (READY).

  1. Depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is recorded (Click here).

    HINT:
    Reinstall the relay, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.


    Result:

    Result
    Proceed to
    DTC (C249/49) is not output
    A
    DTC (C1249/49) is output
    B

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE SKID CONTROL ECU (Click here)
A

INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT) (Click here)  

13.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT SWITCH)
C175815E01
  1. Turn the power switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the skid control ECU connector and the stop light switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A44-14 (STP) - A19-1
    Always
    Below 1 Ω
    A44-14 (STP) - Body ground
    Always
    10 kΩ or higher

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SKID CONTROL ECU (Click here)