Home › BRAKE › BRAKE CONTROL › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C1365/54    Accumulator Pressure Sensor Malfunction

for Preparation Click here


DESCRIPTION

The accumulator pressure sensor is built into the brake actuator.
The skid control ECU detects the accumulator pressure from the data sent from the accumulator pressure sensor, and then runs and stops the pump motor by operating the motor relay.
DTCs may be output if the accumulator pressure drops due to frequent braking (this is not a malfunction).

DTC Code
INF Code
DTC Detection Condition
Trouble Area
C1365/54
211
Sensor power 1 (VCM1) voltage is 4.7 V or less or 5.3 V or more for at least 0.05 seconds.
  1. Brake actuator assembly (Accumulator pressure sensor)
  2. Accumulator pressure sensor circuit
  3. Accumulator pressure sensor power supply
  4. Brake actuator assembly
  5. Skid control ECU
↑
212
Ratio of accumulator pressure sensor output voltage (PACC) to sensor power 1 (VCM1) voltage is 5% or less or 90.5% or more for at least 0.05 seconds.
↑
↑
214
Total wheel cylinder pressure sensor exceeds 18 MPa after depressing brake pedal, but accumulator pressure sensor output voltage (PACC) changes less than 0.5 MPa for at least 0.5 seconds.
↑
↑
215
Ratio of accumulator pressure sensor output voltage (PACC) to sensor power 1 (VCM1) voltage is 90.5% or less for at least 0.1 seconds during self diagnosis.
↑
↑
216
Voltage difference is 0.3 V or more before and after changing the pull up resistance in sensor signal input circuit (loose contact).
↑

WIRING DIAGRAM

Refer to DTCs C1246/46, C1281/81 and C1364/61 .

INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU or brake actuator assembly, perform initialization and calibration of the linear solenoid valve (Click here).

1.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE ACTUATOR)
C173885E01
  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the skid control ECU connector and the brake actuator connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A46-8 (E) - A24-45 (E1)
    Always
    Below 1 Ω
    A46-8 (E) - Body ground
    Always
    10 kΩ or higher
    A46-9 (VCM1) - A24-35 (VCM1)
    Always
    Below 1 Ω
    A46-9 (VCM1) - Body ground
    Always
    10 kΩ or higher
    A46-21 (PACC) - A24-46 (PACC)
    Always
    Below 1 Ω
    A46-21 (PACC) - Body ground
    Always
    10 kΩ or higher
    A46-31 (PCK1) - A24-37 (PCK1)
    Always
    Below 1 Ω
    A46-31 (PCK1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT SKID CONTROL ECU (SENSOR INPUT)


    C173833E10
  1. Reconnect the skid control ECU connector and the brake actuator connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A46-9 (VCM1) - Body ground
    Power switch on (IG)
    4.75 to 5.25 V



NG
REPLACE SKID CONTROL ECU (Click here)
OK


3.INSPECT SKID CONTROL ECU (SENSOR OUTPUT)


    C173833E11
  1. Depress the brake pedal to operate the pump motor, and then check that the pump motor stops.

  1. Measure the voltage according to the value(s) in the table below.

    NOTICE:
    Do not depress the brake pedal until the pump motor stops and the voltage check is finished in order to keep the accumulator pressure.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A46-21 (PACC) - Body ground
    Power switch on (IG)
    3.3 to 4.7 V



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK


4.READ VALUE USING TECHSTREAM (ACCUMULATOR PRESSURE SENSOR)
  1. Turn the power switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the Data List mode on the Techstream (Click here).

    ABS / VSC / TRAC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Accumulator Sensor
    Accumulator pressure sensor /
    min.: 0 V, max.: 5 V
    Specified value: 3.3 to 4.7 V
    -

  1. Depress the brake pedal 4 or 5 times to operate the pump motor, and check the output value on the Techstream with the motor stopped (brake pedal not depressed).

    OK:
    Accumulator pressure sensor voltage does not drop.



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK


5.RECONFIRM DTC
  1. Turn the power switch off.

  1. Clear the DTCs (Click here).

  1. Perform a road test.

  1. Check if the same DTC is recorded (Click here).

    Result:

    Result
    Proceed to
    DTC (C1365/54) is not output
    A
    DTC (C1365/54) is output
    B



B
REPLACE SKID CONTROL ECU (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)