Home › BRAKE › BRAKE CONTROL › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C1377/43    Capacitor Malfunction

for Preparation Click here


DESCRIPTION

The brake control power supply (capacitor) is used as auxiliary power for brake control when the auxiliary battery voltage is low.

DTC Code
INF Code
DTC Detection Condition
Trouble Area
C1377/43
101
Brake control power supply is deteriorated (replacement necessary).
Brake control power supply (Capacitor)
↑
102
Self discharge (current leak) is excessive (internal malfunction).
↑
↑
103
Overvoltage (16.4 V or more) continues to be applied from the auxiliary battery to the capacitor voltage input (+BC) for 10 seconds or more.
Apply high voltage
↑
105
Circuit inside the power back up unit (charge) is malfunctioning.
Brake control power supply (Capacitor)
↑
106
Circuit inside the power back up unit (back up output circuit) is malfunctioning.
↑
↑
108
Circuit inside the power back up unit (voltage monitor circuit) is malfunctioning.
↑
↑
109
Open circuit between auxiliary battery (12 V) and capacitor power input (+BC terminal).
  1. ABS NO. 3 fuse
  2. Brake control power supply circuit
↑
110
Either of the following is detected:
  1. Open or short circuit between auxiliary battery (12 V) and capacitor output 1 (OUT1).
  2. Open or short circuit between auxiliary battery (12 V) and capacitor output 2 (OUT2).
  1. ABS NO. 1 fuse
  2. ABS NO. 2 fuse
  3. Brake control power supply circuit

WIRING DIAGRAM

Refer to DTCs C1241/41 and C1242/42 .

INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU, perform initialization and calibration of the linear solenoid valve (Click here).

1.CHECK FREEZE FRAME DATA
  1. Check the INF code from the Freeze Frame Data memorized when the DTC (C1377/43) is stored (Click here).

    Result:

    Result
    Proceed to
    INF codes (109 and/or 110) are output
    A
    INF codes (101, 102, 105, 106 and/or 108) are output
    B
    INF code (103) is output
    C



B
REPLACE BRAKE CONTROL POWER SUPPLY (Click here)

C
Go to step 9
A


2.INSPECT ABS NO. 3 FUSE


    C173888E02
  1. Remove the ABS NO. 3 fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    ABS NO. 3 (15 A) fuse
    Always
    Below 1 Ω



NG
REPLACE ABS NO. 3 FUSE
OK


3.INSPECT BRAKE CONTROL POWER SUPPLY (+BC TERMINAL)


    C156530E01
  1. Install the ABS NO. 3 fuse.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the brake control power supply connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    O40-8 (+BC) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (+BC CIRCUIT)
OK


4.INSPECT BRAKE CONTROL POWER SUPPLY (GND TERMINAL)


    C156530E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O40-14 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


5.INSPECT SKID CONTROL ECU (+BI TERMINAL)
C173889E02
  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the skid control ECU connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A44-3 (+BI1) - Body ground
    Always
    11 to 14 V
    A47-5 (+BI2) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (+BI CIRCUIT)
OK


6.INSPECT SKID CONTROL ECU (RELAY INPUT)


    C173833E09
  1. Reconnect the skid control ECU connectors.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A44-5 (+BO1) - Body ground
    Power switch on (IG)
    8.8 to 14 V
    A47-4 (+BO2) - Body ground
    Power switch on (IG)
    8.8 to 14 V



NG
REPLACE SKID CONTROL ECU (Click here)
OK


7.INSPECT BRAKE CONTROL POWER SUPPLY (OUT AND CTY+ TERMINAL)


    C140721E02
  1. Reconnect the brake control power supply connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    HINT:
    Perform inspection while the brake pedal is not depressed.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O40-1 (OUT1) - Body ground
    Power switch on (IG)
    11 to 14 V
    O40-2 (CTY+) - Body ground
    Power switch on (IG)
    11 to 14 V (*1)
    O40-7 (OUT2) - Body ground
    Power switch on (IG)
    11 to 14 V

    (*1): For 5 seconds after the driver's door is opened.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (OUT OR CTY+ CIRCUIT)
OK


8.RECONFIRM DTC
  1. Turn the power switch off.

  1. Clear the DTCs (Click here).

  1. Turn the power switch on (IG).

  1. Check if the same DTC is recorded (Click here).

    Result:

    Result
    Proceed to
    DTC (C1377/43) is not output
    A
    DTC (C1377/43) is output
    B



B
REPLACE SKID CONTROL ECU (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)  

9.CHECK AUXILIARY BATTERY
  1. Check the auxiliary battery voltage.

    Standard voltage:
    11 to 14 V



NG
CHARGE OR REPLACE AUXILIARY BATTERY
OK


10.INSPECT BRAKE CONTROL POWER SUPPLY (+BC TERMINAL)
C156530E01
  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the brake control power supply connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    O40-8 (+BC) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (+BC CIRCUIT)
OK


11.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the power switch on (IG).

  1. Check if the same DTC is recorded (Click here).

    Result:

    Result
    Proceed to
    DTC (C1377/43) is not output
    A
    DTC (C1377/43) is output
    B



B
REPLACE BRAKE CONTROL POWER SUPPLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)