Home › BRAKE › BRAKE CONTROL › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C1378/44    Capacitor Communication Malfunction

for Preparation Click here


DESCRIPTION

The brake control power supply (capacitor) provides auxiliary power for brake control when the auxiliary battery (12 V) voltage drops.
The FAIL and ENA lines are placed between the skid control ECU and the brake control power supply.
Signals indicating that the brake control power supply is in auxiliary mode are sent to the skid control ECU through the FAIL line.
Charge permit prohibition signals are sent to the brake control power supply through the ENA line.

DTC Code
INF Code
DTC Detection Condition
Trouble Area
C1378/44
112
Either of the following is detected:
  1. Open or short in FAIL line.
  2. Malfunction inside the power back up unit.
  1. Brake control power supply (Capacitor)
  2. Brake control power supply circuit

WIRING DIAGRAM


C175291E01


INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU, perform initialization and calibration of the linear solenoid valve (Click here).

1.INSPECT BRAKE CONTROL POWER SUPPLY (IG1 TERMINAL)
C156530E05
  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the brake control power supply connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O40-5 (IG1) - Body ground
    Power switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)
OK


2.INSPECT BRAKE CONTROL POWER SUPPLY (GND TERMINAL)


    C156530E02
  1. Turn the power switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O40-14 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE CONTROL POWER SUPPLY)
C175297E01
  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A44-30 (ENA) - O40-12 (ENA)
    Always
    Below 1 Ω
    A44-30 (ENA) - Body ground
    Always
    10 kΩ or higher
    A44-20 (FAIL) - O40-13 (FAIL)
    Always
    Below 1 Ω
    A44-20 (FAIL) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.RECONFIRM DTC
  1. Reconnect the skid control ECU connector and the brake control power supply connector.

  1. Clear the DTCs (Click here).

  1. Turn the power switch on (IG).

  1. Check if the same DTC is recorded (Click here).

    Result:

    Result
    Proceed to
    DTC (C1378/44) is output
    A
    DTC (C1378/44) is not output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)
A


5.CHECK FREEZE FRAME DATA
  1. Check the INF code from the Freeze Frame Data memorized when the DTC (C1378/44) is stored (Click here).

    Result:

    Result
    Proceed to
    INF code (112) is not output
    A
    INF code (112) is output
    B



B
REPLACE BRAKE CONTROL POWER SUPPLY (Click here)
A

REPLACE SKID CONTROL ECU (Click here)