Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function)
RM3160E _58 Vehicle Interior _019706 THEFT DETERRENT / KEYLESS ENTRY _0095461 SMART ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (IG)  


DESCRIPTION

If the engine switch is pressed with the electrical key transmitter sub-assembly in the cabin, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode.

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Power source mode does not change to on (IG) but does change to on (ACC)
Power Source Control
·

Power Supply Condition

·

IG Relay Monitor (Inside)

·

IG Relay Monitor (Outside)

·

IG Circuit


Starting Control
·

Ignition



CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The smart entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.

·

If the smart entry and start system (for Start Function) has been canceled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>CUSTOMIZE PARAMETERS

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to smart entry and start system (for Start Function) Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>PRECAUTION

·

After completing repairs, confirm that the problem does not recur.



HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


PROCEDURE

1.CHECK FOR DTC
a.

Using the GTS, check for certification ECU (smart key ECU assembly) DTCs.

Body Electrical > Power Source Control > Trouble Codes
50001 223
Body Electrical > Entry&Start > Trouble Codes
50001 125
Body Electrical > Starting Control > Trouble Codes
50001 221

Result:
Result Proceed to
DTCs are not output A
Smart entry and start system (for Start Function) DTCs are output B



A

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

B

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the F10 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 4A instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F10-3 (IG1D) - 4A-16 Always Below 1 Ω
F10-3 (IG1D) or 4A-16 - Body ground Always 10 kΩ or higher
4A-27 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - SEMICONDUCTOR PWR INTEGRATION ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - SEMICONDUCTOR PWR INTEGRATION ECU)
a.

Disconnect the 1E semiconductor pwr integration ECU connector.


b.

Disconnect the 4A instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-17 - 1E-1 Always Below 1 Ω
4A-17 or 1E-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 1, IG1 NO. 2, IG1 NO. 3 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 1, IG1 NO. 2, IG1 NO. 3 RELAY)
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

B360715C01
3.302,0.104 3.635,0.333 0.333,0.229 1.719,1.438 2.052,1.667 0.333,0.229 4.781,1.438 5.115,1.667 0.333,0.229 3.396,0.125 3.708,0.323 0.313,0.198 10 false 4A 1.813,1.458 2.125,1.656 0.313,0.198 10 false 4F 4.865,1.458 5.177,1.656 0.313,0.198 10 false 4K 0.229,0.156 0.542,0.313 0.313,0.156 10 false *a
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
4A-16 - 4A-27 20°C (68°F) 87.32 to 127.14 Ω
4K-1 - 4A-35 Battery voltage applied to terminals 4A-16 and 4A-27 Below 1 Ω
Battery voltage not applied to terminals 4A-16 and 4A-27 10 kΩ or higher
4K-1 - 4A-22 Battery voltage applied to terminals 4A-16 and 4A-27 Below 1 Ω
Battery voltage not applied to terminals 4A-16 and 4A-27 10 kΩ or higher
4K-1 - 4F-16 Battery voltage applied to terminals 4A-16 and 4A-27 Below 1 Ω
Battery voltage not applied to terminals 4A-16 and 4A-27 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT SEMICONDUCTOR PWR INTEGRATION ECU (IG2 RELAY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.INSPECT SEMICONDUCTOR PWR INTEGRATION ECU (IG2 RELAY)
a.

Remove the semiconductor pwr integration ECU.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>REMOVAL


b.

Inspect the semiconductor pwr integration ECU.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE SEMICONDUCTOR PWR INTEGRATION ECU (IG2 RELAY)

6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the F10 certification ECU (smart key ECU assembly) connector.


b.

Install the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


c.

Install the semiconductor pwr integration ECU.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>INSTALLATION


d.
C277840C20
1.427,0.188 1.854,0.385 0.427,0.198 1.219,1.74 1.229,0.906 false 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 1.531,0.208 1.99,0.406 0.458,0.198 10 false F10 1.083,1.802 1.427,1.979 0.344,0.177 10 false IG1D
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F10-3 (IG1D) - Body ground Engine switch on (ACC) → Engine switch on (IG) 1 V or less → 9 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)