Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019662 2GR-FE ENGINE CONTROL _0101052 SFI SYSTEM J

2GR-FE ENGINE CONTROL  SFI SYSTEM  Fuel Pump Control Circuit  


DESCRIPTION

The fuel pump circuit consists of the ECM, fuel pump and fuel pump control ECU assembly (which operates the fuel pump). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump control ECU assembly. Based on the signal sent from the ECM, the fuel pump ECU adjusts the fuel pump operation speed.

WIRING DIAGRAM

A315021E01
0.406,2.167 1.781,2.365 1.375,0.198 10 false Fuel Pump 0.406,2.01 1.781,2.208 1.375,0.198 10 false M9 1.052,0.927 1.354,1.135 0.302,0.208 10 false 4 1.063,1.615 1.365,1.823 0.302,0.208 10 false 5 3.031,0.927 3.333,1.135 0.302,0.208 10 false 6 3.031,1.625 3.333,1.833 0.302,0.208 10 false 5 3.042,2.302 3.344,2.51 0.302,0.208 10 false 4 4.292,0.969 4.594,1.177 0.302,0.208 10 false 2 4.302,2.302 4.604,2.51 0.302,0.208 10 false 1 5.635,0.969 5.938,1.177 0.302,0.208 10 false 18 3.24,1.031 3.542,1.24 0.302,0.208 10 false FP 3.24,1.708 3.542,1.917 0.302,0.208 10 false FP- 3.25,2.417 3.552,2.625 0.302,0.208 10 false E 3.896,1.094 4.354,1.302 0.458,0.208 10 false FPC 4,2.417 4.458,2.625 0.458,0.208 10 false +B 5.896,1.094 6.354,1.302 0.458,0.208 10 false FPC 5.906,4.573 6.365,4.781 0.458,0.208 10 false MREL 5.635,4.438 5.938,4.646 0.302,0.208 10 false 46 4.563,4.552 4.865,4.76 0.302,0.208 10 false 1G 4.573,4.135 4.875,4.344 0.302,0.208 10 false 1G 4.625,4.385 4.927,4.594 0.302,0.208 10 false 6 4.625,3.948 4.927,4.156 0.302,0.208 10 false 8 1.875,4.135 2.177,4.344 0.302,0.208 10 false 1H 1.917,3.958 2.219,4.167 0.302,0.208 10 false 1 3.438,4.875 4.417,5.146 0.979,0.271 10 false EFI MAIN 2.604,5.344 5.135,5.563 2.531,0.219 10 false Semiconductor Pwr Integration ECU 6.281,5.875 6.74,6.083 0.458,0.208 10 false ECM 5.948,5.875 6.406,6.083 0.458,0.208 10 false A43 2.479,4.292 3.156,4.458 0.677,0.167 10 false EFI-MAIN 0.583,4.698 1.781,4.969 1.198,0.271 10 false FL MAIN 0.76,5.677 1.958,5.948 1.198,0.271 10 false Battery 2.698,2.948 3.896,3.219 1.198,0.271 10 false M28 2.698,3.115 4.948,3.385 2.25,0.271 10 false Fuel Pump Control ECU Assembly 4.51,2.552 5.25,2.729 0.74,0.177 10 false FUEL PMP

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 230

e.

Check whether fuel pump operating sounds can be heard while operating the fuel pump using the GTS.

OK:

Operating sounds can be heard from the fuel pump.


Result:
Proceed to
OK
NG




OK

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP DUTY)

NG

10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL PUMP CONTROL ECU ASSEMBLY)
2.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP DUTY)
A240046C05
1.927,0.958 2.344,1.677 false 1.521,0.958 1.083,1.677 false 0.125,0.115 0.323,0.281 0.198,0.167 10 false *a 2.333,1.708 2.552,1.927 0.219,0.219 10 false 4 1,1.708 1.24,1.927 0.24,0.219 10 false 5
*a Component with harness connected
(Fuel Pump)


a.

b.

Clean the fuel pump to completely remove any remaining fuel.


c.

Connect the fuel pump connector.

CAUTION:

Confirm that no fuel remains inside or on the outside of the fuel pump.



d.

Connect the GTS to the DLC3.


e.

Turn the ignition switch to ON.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty.

Powertrain > Engine > Active Test
Tester Display
Control the Fuel Pump Duty
50004 234 229

h.

Operate the fuel pump using the Active Test and measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection GTS Operation Specified Condition
4 - 5 Fuel pump control duty: 25% 3.4 to 4.1 V
Fuel pump control duty: 80% 10.0 to 12.5 V



i.

Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.


j.

Operate the fuel pump using the Active Test and measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection GTS Operation Specified Condition
4 - 5 ON (Fuel pump control duty: 90%) 10.2 to 14.0 V


HINT:
·

Be sure to measure the voltage with the all connectors connected.

·

Before performing this inspection, check that the battery voltage is between 11 and 14 V (not depleted).




Result:
Proceed to
OK
NG



OK

3.INSPECT FUEL PUMP

NG

5.INSPECT FUEL PUMP
3.INSPECT FUEL PUMP
a.

Inspect the fuel pump.

Click hereEngine / Hybrid System>2GR-FE FUEL>FUEL PUMP>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

END

NG

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check the fuel pump operation.

OK:

Malfunction has been repaired successfully.



Result:
Proceed to
OK
NG



OK

END

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

5.INSPECT FUEL PUMP
a.

Inspect the fuel pump.

Click hereEngine / Hybrid System>2GR-FE FUEL>FUEL PUMP>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - FUEL PUMP)

NG

6.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - FUEL PUMP)
a.

Disconnect the fuel pump control ECU assembly connector.


b.

Disconnect the fuel pump connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M28-6 (FP) - M9-4 Always Below 1 Ω
M28-5 (FP-) - M9-5 Always Below 1 Ω
M28-6 (FP) or M9-4 - Body ground Always 10 kΩ or higher
M28-5 (FP-) or M9-5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)
a.

Disconnect the fuel pump control ECU assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M28-2 (FPC) - A43-18 (FPC) Always Below 1 Ω
M28-2 (FPC) or A43-18 (FPC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.REPLACE FUEL PUMP CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE FUEL PUMP CONTROL ECU ASSEMBLY
a.

Replace the fuel pump control ECU assembly.

Click hereEngine / Hybrid System>2GR-FE FUEL>FUEL PUMP ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check the fuel pump operation.

OK:

Malfunction has been repaired successfully.



Result:
Proceed to
OK
NG



OK

END

NG

10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL PUMP CONTROL ECU ASSEMBLY)
A256531C03
0.573,1.125 1.031,1.406 0.458,0.281 1.323,1.469 1.271,1.792 false 1.781,1.49 1.854,1.813 false 0.677,1.188 1.177,1.625 0.5,0.438 10 false M28 0.542,0.229 1.073,0.594 0.531,0.365 10 false *a 1.115,1.802 1.51,2.177 0.396,0.375 10 false +B 1.844,1.813 2.26,2.042 0.417,0.229 10 false E
*a Front view of wire harness connector
(to Fuel Pump Control ECU Assembly)


a.

Disconnect the fuel pump control ECU assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M28-1 (+B) - M28-4 (E) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

11.INSPECT FUEL PUMP

NG

16.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - BODY GROUND)
11.INSPECT FUEL PUMP
a.

Inspect the fuel pump.

Click hereEngine / Hybrid System>2GR-FE FUEL>FUEL PUMP>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - FUEL PUMP)

NG

12.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - FUEL PUMP)
a.

Disconnect the fuel pump control ECU assembly connector.


b.

Disconnect the fuel pump connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M28-6 (FP) - M9-4 Always Below 1 Ω
M28-5 (FP-) - M9-5 Always Below 1 Ω
M28-6 (FP) or M9-4 - Body ground Always 10 kΩ or higher
M28-5 (FP-) or M9-5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)
a.

Disconnect the fuel pump control ECU assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M28-2 (FPC) - A43-18 (FPC) Always Below 1 Ω
M28-2 (FPC) or A43-18 (FPC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.REPLACE FUEL PUMP CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.REPLACE FUEL PUMP CONTROL ECU ASSEMBLY
a.

Replace the fuel pump control ECU assembly.

Click hereEngine / Hybrid System>2GR-FE FUEL>FUEL PUMP ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check the fuel pump operation.

OK:

Malfunction has been repaired successfully.



Result:
Proceed to
OK
NG



OK

END

NG

16.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - BODY GROUND)
a.

Disconnect the fuel pump control ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M28-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - SEMICONDUCTOR PWR INTEGRATION ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - SEMICONDUCTOR PWR INTEGRATION ECU)
a.

Disconnect the fuel pump control ECU assembly connector.


b.

Disconnect the semiconductor pwr integration ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M28-1 (+B) - 1G-8 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

18.INSPECT SEMICONDUCTOR PWR INTEGRATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.INSPECT SEMICONDUCTOR PWR INTEGRATION ECU
a.

Inspect the semiconductor pwr integration ECU (EFI MAIN relay).

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE SEMICONDUCTOR PWR INTEGRATION ECU