Home › Engine / Hybrid System › 2GR-FE ENGINE MECHANICAL › ENGINE UNIT › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019663 2GR-FE ENGINE MECHANICAL _0109583 ENGINE UNIT A

2GR-FE ENGINE MECHANICAL  ENGINE UNIT  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the engine assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 89422 1.INSTALL ENGINE COOLANT TEMPERATURE SENSOR

Hide 82219A 2.INSTALL KNOCK CONTROL SENSOR WIRE

a.

Engage the 3 clamps.


Hide 89615 3.INSTALL KNOCK CONTROL SENSOR

Hide 83530 4.INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 25860A 5.INSTALL NO. 1 VACUUM SWITCHING VALVE

a.

Install the No. 1 vacuum switching valve with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16604 6.INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

a.

Install the idler pulley cover plate, No. 2 idler pulley sub-assembly and No. 2 idler pulley cover plate with the bolt.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)


Hide 16173 7.INSTALL WATER PUMP PULLEY

a.

Temporarily install the water pump pulley with the 4 bolts.


b.

Using SST, hold the water pump pulley.

SST
09960-10010  (09962-01000, 09963-00700)


c.

Tighten the 4 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 11322F 8.INSTALL NO. 2 TIMING GEAR COVER

a.

Install the No. 2 timing gear cover with the 2 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 16620 9.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

a.
A129644N01
2.021,0.552 3.094,1.219 false 2.063,1.354 2.635,1.74 true 2.365,0.542 2.49,0.688 0.125,0.146 10 true A 2.24,0.948 2.365,1.094 0.125,0.146 10 true B 2.396,1.156 2.521,1.302 0.125,0.146 10 true B 1.146,1.698 1.271,1.844 0.125,0.146 10 true B 1.083,1.104 1.208,1.25 0.125,0.146 10 true B 2.677,1.688 2.802,1.833 0.125,0.146 10 false 2 3.094,1.135 3.219,1.281 0.125,0.146 10 false 1

Temporarily install the V-ribbed belt tensioner assembly with the 5 bolts.

HINT:

Each bolt length is as follows:

Item Length
Bolt (A) 70 mm (2.76 in.)
Bolt (B) 33 mm (1.30 in.)



b.

Install the V-ribbed belt tensioner assembly by tightening the bolt (1) and then the bolt (2).

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


c.

Tighten the other bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 12321A 10.INSTALL REAR ENGINE MOUNTING BRACKET

a.

Install the rear engine mounting bracket with the 3 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 12315A 11.INSTALL ENGINE MOUNTING BRACKET RH

a.

Install the engine mounting bracket RH with the 3 bolts.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)


Hide 17173A 12.INSTALL EXHAUST MANIFOLD TO HEAD GASKET LH

Hide 17105 13.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH (TWC: Front Catalyst)

Hide 17168 14.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Hide 12142 16.INSTALL NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Install a new O-ring to the No. 2 engine oil level dipstick guide.


b.

Apply a light coat of engine oil to the O-ring.


c.

Push the No. 2 engine oil level dipstick guide end into the engine oil level dipstick guide.


d.

Install the No. 2 engine oil level dipstick guide with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


e.

Install the engine oil level dipstick.


Hide 17173 17.INSTALL EXHAUST MANIFOLD TO HEAD GASKET

Hide 17104 18.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH (TWC: Front Catalyst)

Hide 17125 20.INSTALL NO. 1 SURGE TANK STAY

NOTICE:

Do not apply oil to the bolt listed below:

Oil Application Prohibited Bolt
Bolt for No. 1 Surge Tank Stay and Cylinder Head Cover


a.

Install the No. 1 surge tank stay with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 22267A 21.INSTALL THROTTLE BODY BRACKET

NOTICE:

Do not apply oil to the bolt listed below:

Oil Application Prohibited Bolt
Bolt for Throttle Body Bracket and Cylinder Head Cover


a.

Install the throttle body bracket with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 27020 23.INSTALL GENERATOR ASSEMBLY