Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function) › from 2016.11
RM3160E _58 Vehicle Interior _019706 THEFT DETERRENT / KEYLESS ENTRY _0095461 SMART ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (IG and ACC)  


DESCRIPTION

If any of the following operations are performed, the certification ECU (smart key ECU assembly) receives a signal, and changes the power source mode.

·

With the electrical key transmitter sub-assembly in the cabin, the engine switch is pressed.

·

When the transmitter battery of the electrical key transmitter sub-assembly is depleted, the brake pedal is depressed with the electrical key transmitter sub-assembly held near the engine switch.

·

When the smart entry and start system has been canceled, the brake pedal is depressed with the electrical key transmitter sub-assembly held near the engine switch.


Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Power source mode does not change to on (IG) or on (ACC)
Power Source Control
·

Start Switch1

·

Start Switch2

·

IG Relay Monitor (Inside)

·

ACC Relay Monitor

·

IG Relay Monitor (Outside)

·

Latch Circuit

·

Power Supply Condition


Starting Control
·

Ignition



WIRING DIAGRAM

B463047E04
0.875,4.792 1.969,5.198 1.094,0.406 10 false Stop Light Switch Assembly 0.885,4.635 1.313,4.833 0.427,0.198 10 false A87 0.74,3.823 1.167,4.021 0.427,0.198 10 false 7 0.76,4.198 1.188,4.396 0.427,0.198 10 false 2 1.813,4 2.24,4.198 0.427,0.198 10 false 3 0.927,3.906 1.354,4.104 0.427,0.198 10 false B 1.625,4.115 2.052,4.313 0.427,0.198 10 false L 0.927,4.313 1.354,4.51 0.427,0.198 10 false GND 2.417,3.938 2.844,4.135 0.427,0.198 10 false 2 2.375,5.99 2.802,6.188 0.427,0.198 10 false 11 2.656,6.198 3.083,6.396 0.427,0.198 10 false E 2.656,4.135 3.083,4.333 0.427,0.198 10 false STP1 2.667,2.521 3.135,2.719 0.469,0.198 10 false AGND 2.385,2.354 2.813,2.552 0.427,0.198 10 false 12 2.385,1.906 2.813,2.104 0.427,0.198 10 false 18 2.385,1.469 2.813,1.667 0.427,0.198 10 false 16 2.354,0.396 2.781,0.594 0.427,0.198 10 false F13 2.385,0.177 2.813,0.375 0.427,0.198 10 false 10 2.656,0.385 3.083,0.583 0.427,0.198 10 false +B 2.667,1.656 3.094,1.854 0.427,0.198 10 false SSW1 2.677,2.104 3.104,2.302 0.427,0.198 10 false SSW2 1.635,0.521 2.063,0.719 0.427,0.198 10 false AM2 0.271,0.365 1.208,0.583 0.938,0.219 10 false from Battery 1.313,1.521 1.74,1.719 0.427,0.198 10 false 5 1.313,1.979 1.74,2.177 0.427,0.198 10 false 1 1.323,2.417 1.75,2.615 0.427,0.198 10 false 6 0.938,1.635 1.365,1.833 0.427,0.198 10 false SS1 0.948,2.083 1.375,2.281 0.427,0.198 10 false SS2 0.438,2.854 0.865,3.052 0.427,0.198 10 false F49 0.438,3 1.635,3.208 1.198,0.208 10 false Engine Switch 3.531,0.521 3.958,0.719 0.427,0.198 10 false 9 3.448,0.719 3.875,0.917 0.427,0.198 10 false F13 4.01,0.146 4.438,0.344 0.427,0.198 10 false 1 3.969,0.344 4.396,0.542 0.427,0.198 10 false 4K 3.969,0.531 4.396,0.729 0.427,0.198 10 false 28 3.969,0.708 4.396,0.906 0.427,0.198 10 false 4A 3.979,2.604 4.406,2.802 0.427,0.198 10 false 16 3.969,2.792 4.396,2.99 0.427,0.198 10 false 4A 3.521,2.594 3.948,2.792 0.427,0.198 10 false 3 3.99,3.865 4.417,4.063 0.427,0.198 10 false 17 4.021,5 4.448,5.198 0.427,0.198 10 false 4 3.979,5.177 4.406,5.375 0.427,0.198 10 false 1G 4.021,5.333 4.448,5.531 0.427,0.198 10 false 1 3.979,5.51 4.406,5.708 0.427,0.198 10 false 1E 3.031,2.792 3.458,2.99 0.427,0.198 10 false IG1D 2.979,0.708 3.427,0.906 0.448,0.198 10 false ACCD 2.365,1.656 2.792,1.854 0.427,0.198 10 false F13 2.354,2.104 2.781,2.302 0.427,0.198 10 false F13 2.354,2.542 2.781,2.74 0.427,0.198 10 false F13 2.344,4.135 2.771,4.333 0.427,0.198 10 false F10 2.354,6.208 2.781,6.406 0.427,0.198 10 false F13 0.833,2.542 1.302,2.74 0.469,0.198 10 false AGND 3.448,2.792 3.875,2.99 0.427,0.198 10 false F10 3.958,4.052 4.385,4.25 0.427,0.198 10 false 4A 6.594,0.333 7.083,0.531 0.49,0.198 10 false 4A 5.25,1.021 6.021,1.219 0.771,0.198 10 false ACC 5.094,2.073 5.865,2.271 0.771,0.198 10 false IG1 NO. 1 5.083,3.115 5.854,3.313 0.771,0.198 10 false IG1 NO. 2 5.125,4.292 5.896,4.49 0.771,0.198 10 false IG1 NO. 3 5.823,0.479 6.594,0.677 0.771,0.198 10 false ECU-ACC 5.875,1.5 6.646,1.698 0.771,0.198 10 false WASHER 5.885,2.594 6.656,2.792 0.771,0.198 10 false IG1 NO. 1 4.135,4.542 6.823,4.792 2.688,0.25 10 false Instrument Panel Junction Block Assembly 4.375,5.323 5.146,5.521 0.771,0.198 10 false IG2-EFI 5.74,5.333 6.51,5.531 0.771,0.198 10 false IG2-MAIN 5.177,5.833 5.51,6.01 0.333,0.177 10 false IG2 4.271,6.198 6.448,6.417 2.177,0.219 10 false Smiconductor Pwr Integration ECU 6.604,1.188 7.094,1.385 0.49,0.198 10 false 35 6.604,0.146 7.094,0.344 0.49,0.198 10 false 37 6.604,2.302 7.094,2.5 0.49,0.198 10 false 22 6.604,3.385 7.094,3.583 0.49,0.198 10 false 16 6.604,3.771 7.094,3.969 0.49,0.198 10 false 27 6.573,5 7.063,5.198 0.49,0.198 10 false 1 6.521,5.198 7.01,5.396 0.49,0.198 10 false 1H 5.865,3.708 6.635,3.906 0.771,0.198 10 false IG1 NO. 2 6.594,1.375 7.083,1.573 0.49,0.198 10 false 4A 6.583,2.49 7.073,2.688 0.49,0.198 10 false 4A 6.594,3.583 7.083,3.781 0.49,0.198 10 false 4F 6.594,3.969 7.083,4.167 0.49,0.198 10 false 4A 1.292,5.469 2.229,5.688 0.938,0.219 10 false from Battery 0.385,5.635 0.813,5.833 0.427,0.198 10 false STOP

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The smart entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.

·

If the smart entry and start system (for Start Function) has been canceled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>CUSTOMIZE PARAMETERS

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or electrical key transmitter sub-assembly, refer to smart entry and start system (for Start Function) Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>PRECAUTION

·

After completing repairs, confirm that the problem does not recur.



HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


PROCEDURE

1.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Press a switch of the electrical key transmitter sub-assembly.

OK:

The electrical key transmitter sub-assembly LED illuminates.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (KEY LOW BATTERY)

NG

12.INSPECT TRANSMITTER BATTERY
2.READ VALUE USING GTS (KEY LOW BATTERY)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Key Low Battery Transmitter battery depleted No or Yes No: Transmitter battery not depleted
Yes: Transmitter battery depleted
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less. This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new).
Body Electrical > Entry&Start > Data List
Tester Display
Key Low Battery
50003 125 23
OK:

"No" is displayed on the GTS screen.



Result:
Proceed to
OK
NG



OK

3.CHECK POWER SOURCE MODE

NG

3.CHECK POWER SOURCE MODE
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

Press the engine switch with the brake pedal released and check that the power source mode changes.


Result:
Result Proceed to
The power source mode changes A
The power source mode does not change B



A

END (AFFECTED BY WAVE INTERFERENCE)

B

4.CHECK SMART ENTRY AND START SYSTEM (for Start Function)
4.CHECK SMART ENTRY AND START SYSTEM (for Start Function)
a.

Remove the transmitter battery from the electrical key transmitter sub-assembly.


b.
B358060C02
1.125,0.667 1,0.365 1,0.365 0.833,0.365 false 2.177,1.635 2.26,1.948 2.26,1.948 2.417,1.948 false 0.667,0.313 0.979,0.469 0.313,0.156 10 false *1 2.49,1.875 2.802,2.031 0.313,0.156 10 false *2
*1 Engine Switch
*2 Electrical Key Transmitter Sub-assembly


With the brake pedal depressed, hold the electrical key transmitter sub-assembly near the engine switch and check if the power source mode changes.

OK:

The power source mode changes.


HINT:

If the power source mode changes, the cabin verification is malfunctioning.



Result:
Result Proceed to
The power source mode does not change A
The power source mode changes B



A

5.CHECK FOR DTC

B

11.READ VALUE USING GTS (START SWITCH1, START SWITCH2)
5.CHECK FOR DTC
a.

Using the GTS, check for certification ECU (smart key ECU assembly) DTCs.

Body Electrical > Power Source Control > Trouble Codes
50001 223
Body Electrical > Entry&Start > Trouble Codes
50001 125
Body Electrical > Starting Control > Trouble Codes
50001 221

Result:
Result Proceed to
DTCs are not output A
Smart entry and start system (for Start Function) DTCs are output B



A

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

B

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

7.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

7.CHECK HARNESS AND CONNECTOR (GROUND)

OK

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the F10 and F13 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the 4A instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F13-9 (ACCD) - 4A-28 Always Below 1 Ω
F13-9 (ACCD) or 4A-28 - Body ground Always 10 kΩ or higher
F10-3 (IG1D) - 4A-16 Always Below 1 Ω
F10-3 (IG1D) or 4A-16 - Body ground Always 10 kΩ or higher
4A-27 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 1, IG1 NO. 2, IG1 NO. 3, ACC RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 1, IG1 NO. 2, IG1 NO. 3, ACC RELAY)
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

B360715C01
3.302,0.104 3.635,0.333 0.333,0.229 1.719,1.438 2.052,1.667 0.333,0.229 4.781,1.438 5.115,1.667 0.333,0.229 3.396,0.125 3.708,0.323 0.313,0.198 10 false 4A 1.813,1.458 2.125,1.656 0.313,0.198 10 false 4F 4.865,1.458 5.177,1.656 0.313,0.198 10 false 4K 0.229,0.156 0.542,0.313 0.313,0.156 10 false *a
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
4A-16 - 4A-27 20°C (68°F) 87.32 to 127.14 Ω
4A-28 - 4A-27 20°C (68°F) 130.92 to 190.74 Ω
4K-1 - 4A-35 Battery voltage applied to terminals 4A-16 and 4A-27 Below 1 Ω
Battery voltage not applied to terminals 4A-16 and 4A-27 10 kΩ or higher
4K-1 - 4A-22 Battery voltage applied to terminals 4A-16 and 4A-27 Below 1 Ω
Battery voltage not applied to terminals 4A-16 and 4A-27 10 kΩ or higher
4K-1 - 4F-16 Battery voltage applied to terminals 4A-16 and 4A-27 Below 1 Ω
Battery voltage not applied to terminals 4A-16 and 4A-27 10 kΩ or higher
4K-1 - 4A-37 Battery voltage applied to terminals 4A-28 and 4A-27 Below 1 Ω
Battery voltage not applied to terminals 4A-28 and 4A-27 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

10.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Install the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


b.

Connect the F10 and F13 certification ECU (smart key ECU assembly) connectors.


c.

Measure the voltage while confirming the power source mode on the Data List.

C277835C07
5.115,0.844 5.49,1.083 0.375,0.24 1.531,0.854 1.865,1.083 0.333,0.229 1.344,2.615 1.313,1.698 false 4.76,2.573 4.75,1.677 false 0.094,0.052 0.406,0.25 0.313,0.198 10 false *a 1.594,0.885 1.917,1.052 0.323,0.167 10 false F10 5.198,0.885 5.469,1.042 0.271,0.156 10 false F13 1.229,2.646 1.615,2.792 0.385,0.146 10 false IG1D 4.583,2.625 5,2.802 0.417,0.177 10 false ACCD
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state All OFF, ACC ON, IG ON or ST ON All OFF: Engine switch off (ACC and IG)
ACC ON: Engine switch on (ACC)
IG ON: Engine switch on (IG)
ST ON: Sending engine start request signal
-
Body Electrical > Power Source Control > Data List
Tester Display
Power Supply Condition
50003 223 18
Standard Voltage:
Tester Connection Condition Specified Condition
F10-3 (IG1D) - Body ground Engine switch off 1 V or less
Engine switch on (ACC) 1 V or less
Engine switch on (IG) 9 V or higher
F13-9 (ACCD) - Body ground Engine switch off 1 V or less
Engine switch on (ACC) 8.5 V or higher
Engine switch on (IG) 8.5 V or higher



Result:
Proceed to
OK
NG



OK

NG

11.READ VALUE USING GTS (START SWITCH1, START SWITCH2)
11.READ VALUE USING GTS (START SWITCH1, START SWITCH2)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Start Switch1 Engine switch 1 status OFF or ON OFF: Engine switch not pressed
ON: Engine switch pressed
·

If the engine switch is pressed for a short time, the display may not change.

·

Use this item to determine whether the engine switch input signal is malfunctioning.


Start Switch2 Engine switch 2 status OFF or ON OFF: Engine switch not pressed
ON: Engine switch pressed
·

Backup for engine switch 1. However, when the engine switch is pressed and held, the control functions only when both engine switch 1 and 2 are normal.

·

Behaves the same way as engine switch 1.


Body Electrical > Power Source Control > Data List
Tester Display
Start Switch1
Start Switch2
50003 223 4,5
OK:

The GTS display changes correctly in response to the engine switch operation.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

13.INSPECT ENGINE SWITCH
12.INSPECT TRANSMITTER BATTERY
a.

Inspect the transmitter battery.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/ Smart Entry and Start System)>INSPECTION

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.



Result:
Proceed to
OK
NG



OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

13.INSPECT ENGINE SWITCH


Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)

NG

14.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)
a.

Disconnect the F13 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the F49 engine switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F13-16 (SSW1) - F49-5 (SS1) Always Below 1 Ω
F13-16 (SSW1) or F49-5 (SS1) - Body ground Always 10 kΩ or higher
F13-18 (SSW2) - F49-1 (SS2) Always Below 1 Ω
F13-18 (SSW2) or F49-1 (SS2) - Body ground Always 10 kΩ or higher
F13-12 (AGND) - F49-6 (AGND) Always Below 1 Ω
F13-12 (AGND) or F49-6 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR