Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › from 2016.11
RM3160E _58 Vehicle Interior _019713 SEAT BELT _0100669 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Rear Seat Belt Warning Light Malfunction  


DESCRIPTION

The main body ECU (multiplex network body ECU) detects whether either rear door is open or closed based on the condition of the left and right courtesy light switches and then sends the rear door status signal to the combination meter assembly. The combination meter assembly detects the rear seat belt state. The rear seat belt warning lights on the clock assembly illuminate or turn off in accordance with the rear door state, vehicle speed and rear seat belt state.

WIRING DIAGRAM

B357860E02
0.76,8.51 2.51,8.677 1.75,0.167 10 false : CAN Communication Line 0.396,7.698 0.729,7.865 0.333,0.167 10 false MB 2.083,7.292 3.708,7.625 1.625,0.333 10 false Instrument Panel Junction Block Assembly 0.396,7.865 2.042,8.198 1.646,0.333 10 false Main Body ECU (Multiplex Network Body ECU) 4.167,7.354 6.177,7.688 2.01,0.333 10 false Rear Door Courtesy Light Switch Assembly (LH Side) 4.167,7.188 5.313,7.729 1.146,0.542 10 false M14 4.302,6.854 4.5,7.021 0.198,0.167 10 false 1 4.302,5.698 4.5,5.865 0.198,0.167 10 false 1 4.156,6.021 4.406,6.188 0.25,0.167 10 false L13 4.156,6.177 6.167,6.51 2.01,0.333 10 false Rear Door Courtesy Light Switch Assembly (RH Side) 3.531,5.802 3.781,5.969 0.25,0.167 10 false 4D 3.531,6.969 3.781,7.135 0.25,0.167 10 false 4H 3.531,5.573 3.781,5.74 0.25,0.167 10 false 30 3.531,6.74 3.781,6.906 0.25,0.167 10 false 36 2.01,5.698 2.208,5.865 0.198,0.167 10 false 2 2.01,6.854 2.208,7.021 0.198,0.167 10 false 13 1.552,6.958 2,7.125 0.448,0.167 10 false LCTY 1.531,5.802 1.979,5.969 0.448,0.167 10 false RCTY 0.667,4.719 1.875,5.052 1.208,0.333 10 false Combination Meter Assembly 3.417,4.719 4.688,5.104 1.271,0.385 10 false Rear Seat Inner Belt Assembly 5.073,4.719 6.354,5.094 1.281,0.375 10 false Rear Seat Inner Belt Assembly RH 1.51,3.885 2,4.052 0.49,0.167 10 false RRSB 1.51,3.448 2,3.615 0.49,0.167 10 false RCSB 1.531,2.156 2.021,2.323 0.49,0.167 10 false RLSB 1.5,0.802 1.99,0.969 0.49,0.167 10 false RCMT 1.5,0.365 1.99,0.531 0.49,0.167 10 false RRMT 1.521,1.219 2.01,1.385 0.49,0.167 10 false RLMT 2.063,0.365 2.51,0.604 0.448,0.24 10 false F21 2.063,0.802 2.719,1.229 0.656,0.427 10 false F21 2.063,1.219 2.635,1.604 0.573,0.385 10 false F21 2.021,2.146 2.646,2.521 0.625,0.375 10 false F126 2.01,3.438 2.469,3.74 0.458,0.302 10 false F126 2.073,3.667 2.281,3.833 0.208,0.167 10 false 14 2.073,3.229 2.281,3.396 0.208,0.167 10 false 13 2.083,1.938 2.292,2.104 0.208,0.167 10 false 12 2.125,1.01 2.333,1.177 0.208,0.167 10 false 6 2.125,0.583 2.333,0.75 0.208,0.167 10 false 2 2.125,0.156 2.333,0.323 0.208,0.167 10 false 3 3.052,0.26 3.333,0.427 0.281,0.167 10 false 11 3.052,0.688 3.333,0.854 0.281,0.167 10 false 12 3.052,1.125 3.333,1.292 0.281,0.167 10 false 13 3.323,0.365 3.74,0.531 0.417,0.167 10 false RRID 3.323,0.781 3.74,0.948 0.417,0.167 10 false RCID 3.323,1.208 3.74,1.375 0.417,0.167 10 false RLID 4.583,0.813 4.917,0.979 0.333,0.167 10 false IG+ 5.104,0.948 5.823,1.198 0.719,0.25 10 false IG1 NO. 3 6.083,0.792 7.031,1.125 0.948,0.333 10 false from IG1 NO. 3 Relay 3.583,1.563 3.917,1.729 0.333,0.167 10 false G7 3.583,1.729 4.885,1.958 1.302,0.229 10 false Clock Assembly 3.125,2.042 3.323,2.208 0.198,0.167 10 false 3 3.323,2.063 3.771,2.229 0.448,0.167 10 false LBR+ 4.49,2.063 4.906,2.229 0.417,0.167 10 false LBR- 4.927,2.042 5.125,2.208 0.198,0.167 10 false 5 3,4.104 3.208,4.271 0.208,0.167 10 false 4 3,3.677 3.208,3.844 0.208,0.167 10 false 1 3,3.24 3.208,3.406 0.208,0.167 10 false 2 2.99,3.438 3.281,3.604 0.292,0.167 10 false i2 5.042,3.25 5.26,3.417 0.219,0.167 10 false 5 5.042,3.688 5.26,3.854 0.219,0.167 10 false 3 5.042,4.094 5.26,4.26 0.219,0.167 10 false 2 4.594,3.677 4.813,3.844 0.219,0.167 10 false 3 4.604,4.094 4.823,4.26 0.219,0.167 10 false 2 4.594,3.885 4.948,4.156 0.354,0.271 10 false C 4.594,4.313 4.833,4.646 0.24,0.333 10 false C 5.031,4.313 5.344,4.583 0.313,0.271 10 false D 5.031,3.885 5.521,4.198 0.49,0.313 10 false D 5.031,3.438 5.323,3.604 0.292,0.167 10 false i2 4.927,0.688 5.125,0.854 0.198,0.167 10 false 1 2.99,2.448 3.563,2.833 0.573,0.385 10 false j2 2.99,2.615 5.875,2.823 2.885,0.208 10 false Rear Seat 3 Point Type Belt Assembly LH 2.021,3.865 2.479,4.167 0.458,0.302 10 false F126 2.99,3.865 3.281,4.031 0.292,0.167 10 false i2 3,4.292 3.292,4.458 0.292,0.167 10 false i2

CAUTION / NOTICE / HINT

NOTICE:
·

The seat belt warning system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.READ VALUE USING GTS (REAR DOOR COURTESY LIGHT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Door Courtesy SW Rear door courtesy light switch assembly (RH side) signal ON or OFF ON: Rear door RH open
OFF: Rear door RH closed
-
RL Door Courtesy SW Rear door courtesy light switch assembly (LH side) signal ON or OFF ON: Rear door LH open
OFF: Rear door LH closed
-
Body Electrical > Main Body > Data List
Tester Display
RR Door Courtesy SW
RL Door Courtesy SW
50003 123 24,25

OK:

The GTS display changes correctly in response to the rear door condition.


Result:
Proceed to
OK
NG



OK

2.CHECK REAR SEAT BELT WARNING

NG

GO TO LIGHTING SYSTEM (Rear Door Courtesy Switch Circuit)

2.CHECK REAR SEAT BELT WARNING
a.
B353656C01
0.917,1.75 0.917,1.333 false 1.719,1.75 1.719,1.385 false 2.51,1.75 2.51,1.333 false 0.167,0.167 0.417,0.333 0.25,0.167 10 false *1 0.844,1.781 1.094,1.948 0.25,0.167 10 false *a 1.646,1.781 1.896,1.948 0.25,0.167 10 false *b 2.448,1.781 2.698,1.948 0.25,0.167 10 false *c
*1 Rear Seat Belt Warning Light (Clock Assembly)
*a LH
*b Center
*c RH


Check the rear seat belt warning function.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>ON-VEHICLE INSPECTION

Result:
Result Proceed to
The rear seat belt warning lights operate normally A
The rear seat belt warning lights (all seats) do not operate normally B
The rear seat belt warning light (RH) does not operate normally C
The rear seat belt warning light (center) does not operate normally D
The rear seat belt warning light (LH) does not operate normally E




A

B

3.INSPECT REAR SEAT BELT WARNING LIGHT (CLOCK ASSEMBLY)

C

6.READ VALUE USING GTS (REAR RH SEAT BELT BUCKLE SWITCH)

D

11.READ VALUE USING GTS (REAR CENTER SEAT BELT BUCKLE SWITCH)

E

15.READ VALUE USING GTS (REAR LH SEAT BELT BUCKLE SWITCH)
3.INSPECT REAR SEAT BELT WARNING LIGHT (CLOCK ASSEMBLY)
a.

Remove the rear seat belt warning light (clock assembly).

Click hereVehicle Interior>METER / GAUGE / DISPLAY>CLOCK>REMOVAL


b.

Inspect the rear seat belt warning light (LH, center and RH) (clock assembly).

Click hereVehicle Interior>METER / GAUGE / DISPLAY>CLOCK>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (IGNITION POWER SUPPLY - CLOCK ASSEMBLY)

NG

REPLACE REAR SEAT BELT WARNING LIGHT (CLOCK ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (IGNITION POWER SUPPLY - CLOCK ASSEMBLY)
a.

Disconnect the G7 clock assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G7-1 (IG+) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the F21 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F21-3 (RRMT) - G7-11 (RRID) Always Below 1 Ω
F21-3 (RRMT) or G7-11 (RRID) - Body ground Always 10 kΩ or higher
F21-2 (RCMT) - G7-12 (RCID) Always Below 1 Ω
F21-2 (RCMT) or G7-12 (RCID) - Body ground Always 10 kΩ or higher
F21-6 (RLMT) - G7-13 (RLID) Always Below 1 Ω
F21-6 (RLMT) or G7-13 (RLID) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.READ VALUE USING GTS (REAR RH SEAT BELT BUCKLE SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
2nd-Row Seatbelt Buckle (R) Rear RH seat belt buckle switch signal ON or OFF OFF: Rear RH seat belt fastened
ON: Rear RH seat belt not fastened
-
Body Electrical > Combination Meter > Data List
Tester Display
2nd-Row Seatbelt Buckle (R)
50003 122 74
Result:
Result Proceed to
ON or OFF does not appear on the GTS screen according to the rear seat belt condition A
ON or OFF appears on the GTS screen according to the rear seat belt condition B




A

7.INSPECT REAR SEAT INNER BELT ASSEMBLY

B

9.INSPECT REAR SEAT BELT WARNING LIGHT (CLOCK ASSEMBLY)
7.INSPECT REAR SEAT INNER BELT ASSEMBLY


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR SEAT INNER BELT ASSEMBLY - BODY GROUND)

NG

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR SEAT INNER BELT ASSEMBLY - BODY GROUND)
a.

Disconnect the F126 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F126-14 (RRSB) - i2-1 Always Below 1 Ω
F126-14 (RRSB) or i2-1 - Body ground Always 10 kΩ or higher
i2-4 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT REAR SEAT BELT WARNING LIGHT (CLOCK ASSEMBLY)
a.

Remove the rear seat belt warning light (clock assembly).

Click hereVehicle Interior>METER / GAUGE / DISPLAY>CLOCK>REMOVAL


b.

Inspect the rear seat belt warning light (RH) (clock assembly).

Click hereVehicle Interior>METER / GAUGE / DISPLAY>CLOCK>INSPECTION


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CLOCK ASSEMBLY)

NG

REPLACE REAR SEAT BELT WARNING LIGHT (CLOCK ASSEMBLY)

10.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CLOCK ASSEMBLY)
a.

Disconnect the F21 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F21-3 (RRMT) - G7-11 (RRID) Always Below 1 Ω
F21-3 (RRMT) or G7-11 (RRID) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.READ VALUE USING GTS (REAR CENTER SEAT BELT BUCKLE SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
2nd-Row Seatbelt Buckle (C) Rear center seat belt buckle switch signal ON or OFF OFF: Rear center seat belt fastened
ON: Rear center seat belt not fastened
-
Body Electrical > Combination Meter > Data List
Tester Display
2nd-Row Seatbelt Buckle (C)
50003 122 76
Result:
Result Proceed to
ON or OFF does not appear on the GTS screen according to the rear seat belt condition A
ON or OFF appears on the GTS screen according to the rear seat belt condition B




A

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR SEAT INNER BELT ASSEMBLY - BODY GROUND)

B

13.INSPECT REAR SEAT BELT WARNING LIGHT (CLOCK ASSEMBLY)
12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR SEAT INNER BELT ASSEMBLY - BODY GROUND)
a.

Disconnect the F126 combination meter assembly connector.


b.

Disconnect the i2 rear seat inner belt assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F126-13 (RCSB) - i2-2 Always Below 1 Ω
F126-13 (RCSB) or i2-2 - Body ground Always 10 kΩ or higher
i2-5 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT REAR SEAT BELT WARNING LIGHT (CLOCK ASSEMBLY)
a.

Remove the rear seat belt warning light (clock assembly).

Click hereVehicle Interior>METER / GAUGE / DISPLAY>CLOCK>REMOVAL


b.

Inspect the rear seat belt warning light (center) (clock assembly).

Click hereVehicle Interior>METER / GAUGE / DISPLAY>CLOCK>INSPECTION


Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CLOCK ASSEMBLY)

NG

REPLACE REAR SEAT BELT WARNING LIGHT (CLOCK ASSEMBLY)

14.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CLOCK ASSEMBLY)
a.

Disconnect the F21 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F21-2 (RCMT) - G7-12 (RCID) Always Below 1 Ω
F21-2 (RCMT) or G7-12 (RCID) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.READ VALUE USING GTS (REAR LH SEAT BELT BUCKLE SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
2nd-Row Seatbelt Buckle (L) Rear LH seat belt buckle switch signal ON or OFF OFF: Rear LH seat belt fastened
ON: Rear LH seat belt not fastened
-
Body Electrical > Combination Meter > Data List
Tester Display
2nd-Row Seatbelt Buckle (L)
50003 122 75
Result:
Result Proceed to
ON or OFF does not appear on the GTS screen according to the rear seat belt condition A
ON or OFF appears on the GTS screen according to the rear seat belt condition B




A

16.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH - BODY GROUND)

B

17.INSPECT REAR SEAT BELT WARNING LIGHT (CLOCK ASSEMBLY)
16.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH - BODY GROUND)
a.

Disconnect the F126 combination meter assembly connector.


b.

Disconnect the j2 rear seat 3 point type belt assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F126-12 (RLSB) - j2-3 Always Below 1 Ω
F126-12 (RLSB) or j2-3 (LBR+) - Body ground Always 10 kΩ or higher
j2-5 (LBR-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.INSPECT REAR SEAT BELT WARNING LIGHT (CLOCK ASSEMBLY)
a.

Remove the rear seat belt warning light (clock assembly).

Click hereVehicle Interior>METER / GAUGE / DISPLAY>CLOCK>REMOVAL


b.

Inspect the rear seat belt warning light (LH) (clock assembly).

Click hereVehicle Interior>METER / GAUGE / DISPLAY>CLOCK>INSPECTION


Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CLOCK ASSEMBLY)

NG

REPLACE REAR SEAT BELT WARNING LIGHT (CLOCK ASSEMBLY)

18.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CLOCK ASSEMBLY)
a.

Disconnect the F21 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F21-6 (RLMT) - G7-13 (RLID) Always Below 1 Ω
F21-6 (RLMT) or G7-13 (RLID) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR