Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) › from 2016.11
RM3160E _58 Vehicle Interior _019712 SEAT _0107153 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Power Seat does not Return to Memorized Position  


DESCRIPTION

When either the M1 or M2 switch is pressed, the outer mirror control ECU assembly (driver door) sends a switch signal to the main body ECU (multiplex network body ECU) via CAN communication. Then, the main body ECU (multiplex network body ECU) sends a recall request signal to the position control ECU and switch assembly. The position control ECU and switch assembly operates each motor to achieve each memorized position value.

WIRING DIAGRAM

B276669E05
3.49,2.24 3.813,2.385 0.323,0.146 10 false GND 3.271,2.688 4.198,2.948 0.927,0.26 10 false I2*1, H2*2 4.406,0.313 4.635,0.458 0.229,0.146 10 false M1 4.698,0.229 4.927,0.375 0.229,0.146 10 false 2 4.698,0.896 4.927,1.042 0.229,0.146 10 false 3 4.698,1.542 4.927,1.688 0.229,0.146 10 false 1 3.302,2.125 3.479,2.271 0.177,0.146 10 false 7 5.365,0.229 5.531,0.375 0.167,0.146 10 false 4 5.365,0.896 5.531,1.042 0.167,0.146 10 false 3 5.365,1.542 5.531,1.688 0.167,0.146 10 false 8 5.365,2.135 5.531,2.281 0.167,0.146 10 false 2 5.521,0.188 6.219,0.469 0.698,0.281 10 false 1*1, M1*2 5.531,0.854 6.219,1.167 0.688,0.313 10 false 2*1, M2*2 5.531,1.385 6.125,1.708 0.594,0.323 10 false MMRY*1, MRY*2 5.552,2.135 5.719,2.281 0.167,0.146 10 false E 4.406,0.979 4.635,1.125 0.229,0.146 10 false M2 4.354,1.635 4.625,1.781 0.271,0.146 10 false MM 0.135,1.073 1.729,1.5 1.594,0.427 10 false Position Control ECU and Switch Assembly 0.135,2.698 1.781,3.073 1.646,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 3.26,2.854 4.865,3.229 1.604,0.375 10 false Outer Mirror Control ECU Assembly (Driver Door) 5.563,2.708 6.781,3.115 1.219,0.406 10 false I11*1, H12*2 5.563,2.854 6.885,3.208 1.323,0.354 10 false Seat Memory Switch (Driver Door) 0.719,3.458 2.469,3.635 1.75,0.177 10 false : CAN Communication Line 2.042,2.823 2.969,3.083 0.927,0.26 10 false *1: for LHD 2.042,3.135 2.969,3.396 0.927,0.26 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

The seat position will not be stored if the SET switch and 2 of the seat memory switches are pressed simultaneously.

If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.

·

The seat will not return to the memorized position if 2 of the seat memory switches are pressed simultaneously.

If a restoring operation has failed, release all switches. The seat memory restoring function does not operate unless the switches are released.

·

The front power seat control system (w/ Memory) uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD




PROCEDURE

1.CHECK FRONT POWER SEAT CONTROL OPERATION
a.

Check that each function of the power seat operates normally by using the switches on the position control ECU and switch assembly.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

OK:

Each function of the power seat operates normally using the switches on the position control ECU and switch assembly.



Result:
Proceed to
OK
NG



OK

2.CHECK SEAT POSITION MEMORY FUNCTION

NG

2.CHECK SEAT POSITION MEMORY FUNCTION
a.

Check that the seat position memory function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

OK:

Seat position memory function is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK SEAT POSITION RESTORING FUNCTION

NG

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat Position is not Memorized)

3.CHECK SEAT POSITION RESTORING FUNCTION
a.

Under each of the following conditions, check that the seat position restoring function operates by pressing the M1 or M2 switch.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

·

The engine switch is on (IG), and the shift lever is in P.*1

·

The engine switch is turned off within 180 seconds after the driver door is closed and opened.*2

·

The engine switch is turned off within 60 seconds after the driver door is opened and closed.*3


Result:
Result Proceed to
Seat position restoring function does not operate at all A
Seat position restoring function does not operate when the condition is*1 B
·

Seat position restoring function does not operate when the condition is*2

·

Seat position restoring function does not operate when the condition is*3


C




A

4.READ VALUE USING GTS (SEAT POSITION MEMORY)

B

9.READ VALUE USING GTS (SHIFT P POSITION STATE)

C

10.READ VALUE USING GTS (DRIVER DOOR COURTESY SWITCH)
4.READ VALUE USING GTS (SEAT POSITION MEMORY)
a.

Store a seat position in memory for each of the M1 and M2 switches.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Driver Seat / Data List.


f.

Read the Data List according to the display on the GTS.

Body Electrical > Driver Seat > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Seat Memory No1 Seat position memorized with M1 switch Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Seat Memory No2 Seat position memorized with M2 switch Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Body Electrical > Driver Seat > Data List
Tester Display
Seat Memory No1
Seat Memory No2
50003 162 3,4
OK:

Mem appears on the GTS screen.



Result:
Proceed to
OK
NG



OK

5.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)

NG

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat Position is not Memorized)

5.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)
a.

Temporarily replace the outer mirror control ECU assembly (driver door) with a new or known good one.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
6.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
a.

Check that the seat position memory and restoring function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

OK:

Seat position memory and restoring function operates normally.



Result:
Proceed to
OK
NG



OK

END (OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR) WAS DEFECTIVE)

NG

7.REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY
7.REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY
a.

Temporarily replace the position control ECU and switch assembly with a new or known good one.

Click hereVehicle Interior>SEAT>POWER SEAT SWITCH(w/ Seat Position Memory System)>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
8.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
a.

Check that the seat position memory and restoring function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

OK:

Seat position memory and restoring function operates normally.



Result:
Proceed to
OK
NG



OK

END (POSITION CONTROL ECU AND SWITCH ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

9.READ VALUE USING GTS (SHIFT P POSITION STATE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Driver Seat / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Driver Seat > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Switch Park state signal ON or OFF ON: Shift lever in P
OFF: Shift lever in a position other than P
-
Body Electrical > Driver Seat > Data List
Tester Display
P Switch
50003 162 13
OK:

On the GTS screen, the item changes between ON and OFF according to the above.



Result:
Result Proceed to
OK A
NG (for U760E) B
NG (for UA80E or UA80F) C



A

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

B

GO TO AUTOMATIC TRANSAXLE SYSTEM (P0705)

C

10.READ VALUE USING GTS (DRIVER DOOR COURTESY SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy SW Front door courtesy light switch assembly (driver door) signal*2 ON or OFF ON: Driver door open
OFF: Driver door closed
-
FL Door Courtesy SW Front door courtesy light switch assembly (driver door) signal*1 ON or OFF ON: Driver door open
OFF: Driver door closed
-

*1: for LHD

*2: for RHD


Body Electrical > Main Body > Data List
Tester Display
FR Door Courtesy SW
FL Door Courtesy SW
50003 123 197,199
OK:

On the GTS screen, the item changes between ON and OFF according to the above.



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

GO TO LIGHTING SYSTEM (Front Door Courtesy Switch Circuit)