Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › SFI SYSTEM › from 2016.11
RM3160E _51 Engine / Hybrid System _060156 2GR-FKS ENGINE CONTROL _0299070 SFI SYSTEM C

2GR-FKS ENGINE CONTROL  SFI SYSTEM  P001600  Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A  P001800  Crankshaft Position - Camshaft Position Correlation Bank 2 Sensor A  


DESCRIPTION

In the VVT (Variable Valve Timing) system, the appropriate intake valve open and close timing is controlled by the ECM. The ECM performs intake valve control by performing the following: 1) controlling the intake camshaft, cam timing oil control solenoid assembly, camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft]) and operating the camshaft timing gear; and 2) changing the relative positions of the camshaft and crankshaft.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P001600 Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A Deviation in the crankshaft position sensor signal and VVT sensor (for intake camshaft of bank 1) signal (2 trip detection logic).
·

Valve timing

·

Cam timing oil control solenoid assembly (for intake camshaft of bank 1)

·

Camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft of bank 1])

·

Camshaft timing gear assembly (bank 1)

·

Oil control valve filter (for intake camshaft of bank 1)

·

ECM


Comes on/ Does not come on DTC stored SAE Code: P0016
P001800 Crankshaft Position - Camshaft Position Correlation Bank 2 Sensor A Deviation in the crankshaft position sensor signal and VVT sensor (for intake camshaft of bank 2) signal (2 trip detection logic).
·

Valve timing

·

Cam timing oil control solenoid assembly (for intake camshaft of bank 2)

·

Camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft of bank 2])

·

Camshaft timing gear assembly (bank 2)

·

Oil control valve filter (for intake camshaft of bank 2)

·

ECM


Comes on/ Does not come on DTC stored SAE Code: P0018

MONITOR DESCRIPTION

To monitor the correlation of the intake camshaft position and crankshaft position, the ECM checks the VVT learned value while the engine is idling. The VVT learned value is calibrated based on the camshaft position and crankshaft position. The intake valve timing is set to the neutral position while the engine is idling. If the VVT learned value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft timing gear assembly
Required Sensors/Components (Related) VVT sensor
Crankshaft position sensor
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Engine speed 400 to 1000 rpm

CONFIRMATION DRIVING PATTERN

A399789E01
4.281,1.115 4.646,0.292 4.646,0.292 4.802,0.292 false 0.125,0.677 1.323,1.021 1.198,0.344 10 false Vehicle Speed 0.719,1.719 1.406,1.99 0.688,0.271 10 false Idling 0.208,2.063 1.115,2.5 0.906,0.438 10 false Ignition Switch ON 1.563,2.135 1.917,2.427 0.354,0.292 10 false [A] 2.229,1.667 2.604,1.927 0.375,0.26 10 false [B] 3.188,1.667 3.51,1.958 0.323,0.292 10 false [C] 3.813,3.021 4.156,3.313 0.344,0.292 10 false [D] 4.719,0.917 5.052,1.25 0.333,0.333 10 false [E] 5.76,1.656 6.104,1.969 0.344,0.313 10 false [F] 6.365,3.031 6.75,3.365 0.385,0.333 10 false [G] 4.865,0.25 6.292,0.813 1.427,0.563 10 false There is no designated vehicle speed 1.927,2.604 2.698,3 0.771,0.396 10 false Warming up the engine 2.771,2.625 4.021,2.917 1.25,0.292 10 false 5 minutes or more 4.146,2.646 5.167,2.99 1.021,0.344 10 false 2 to 3 minutes 5.25,2.646 6.458,2.948 1.208,0.302 10 false 5 minutes or more

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

7.

Idle the engine for 5 minutes or more [C].

8.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P001600 or P001800.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [G].



13.

Drive the vehicle for 2 to 3 minutes [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


14.

Idle the engine for 5 minutes or more [F].

15.

Enter the following menus: Powertrain / Engine / Trouble Codes [G].

16.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:
·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

The monitor for this DTC detects when the timing chain is shifted by one tooth or more.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.PERFORM SIMULATION TEST (CHECK FOR ABNORMAL NOISE)
a.

Start the engine.


b.

Check for abnormal noise (rattling sounds) from the camshaft timing gear assembly with the engine idling.

Result:
Result Proceed to
Abnormal noise (rattling sound) from the camshaft timing gear assembly is heard. A
Abnormal noise (rattling sound) from the camshaft timing gear assembly is not heard. B


HINT:
·

As the engine speed increases, the camshaft timing gear assembly lock pins will release and the abnormal noise (rattling sound) will disappear.

·

Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION





A

REPLACE CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE [FOR INTAKE CAMSHAFT]) AND CAMSHAFT TIMING GEAR ASSEMBLY

B

2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P001600 OR P001800)
2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P001600 OR P001800)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P001600 or P001800 is output A
DTC P001600 or P001800 and other DTCs are output B


HINT:

If any DTCs other than P001600 or P001800 are output, troubleshoot those DTCs first.




A

3.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO)

B

3.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO)
HINT:

If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.


a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Control the Intake VVT OCV Duty Ratio Bank 1 or Control the Intake VVT OCV Duty Ratio Bank 2 / Data List / Intake VVT Change Angle Bank 1 or Intake VVT Change Angle Bank 2.

Powertrain > Engine > Active Test
Active Test Display
Control the Intake VVT OCV Duty Ratio Bank 1
Data List Display
Intake VVT Change Angle Bank 1
50004 372 4 397
Powertrain > Engine > Active Test
Active Test Display
Control the Intake VVT OCV Duty Ratio Bank 2
Data List Display
Intake VVT Change Angle Bank 2
50004 372 45 469

e.

Perform the Active Test. Check that the displacement angle varies.

OK:

Displacement angle varies.



Result:
Proceed to
OK
NG



OK

4.CHECK ENGINE MECHANICAL SYSTEM

NG

5.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT)
4.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.


Result:
Proceed to
OK
NG



OK

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P001600 OR P001800)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

5.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT)
a.

Inspect the cam timing oil control solenoid assembly (for intake camshaft).

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>CAMSHAFT OIL CONTROL SOLENOID>INSPECTION


Result:
Proceed to
OK
NG



OK

6.INSPECT CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR INTAKE CAMSHAFT])

NG

REPLACE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT)

6.INSPECT CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR INTAKE CAMSHAFT])
a.

Inspect the camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft]).



Result:
Proceed to
OK
NG



OK

7.INSPECT OIL CONTROL VALVE FILTER (FOR INTAKE CAMSHAFT)

NG

REPLACE CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR INTAKE CAMSHAFT])

7.INSPECT OIL CONTROL VALVE FILTER (FOR INTAKE CAMSHAFT)
A370162C01
1.927,0.969 2.188,0.729 2.188,0.729 2.344,0.729 false 5.563,1.01 5.823,0.771 5.823,0.771 5.979,0.771 false 0.719,0.333 1.083,0.521 0.365,0.188 12 false A 3.875,0.333 4.25,0.552 0.375,0.219 12 false B 2.385,0.646 2.698,0.802 0.313,0.156 10 false *1 6,0.688 6.313,0.844 0.313,0.156 10 false *1
A for Intake Camshaft of Bank 1 B for Intake Camshaft of Bank 2
*1 Oil Control Valve Filter - -


a.

Remove the oil control valve filter (for intake camshaft of bank 1) or oil control valve filter (for intake camshaft of bank 2).



b.

Check that the filter is not clogged.

OK:

Filter is not clogged.



Result:
Proceed to
OK
NG



OK

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P001600 OR P001800)

NG

REPLACE OIL CONTROL VALVE FILTER (FOR INTAKE CAMSHAFT)

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P001600 OR P001800)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.


k.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P001600 or P001800 is output B




A

B

9.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
9.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
a.

Replace the camshaft timing gear assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P001600 OR P001800)
10.CHECK WHETHER DTC OUTPUT RECURS (DTC P001600 OR P001800)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.


k.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P001600 or P001800 is output B




A

END

B