Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.11
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0106374 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1337  Diameter of the Tire is not Uniform  


DESCRIPTION

The skid control ECU (brake actuator assembly) measures the speed of each wheel by receiving signals from the speed sensor. These signals are used for recognizing that all 4 wheels are operating properly.

Therefore, all wheel signals must be equal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1337 Diameter of the Tire is not Uniform The following occurs in 3 consecutive times:
At a vehicle speed of 20 km/h (12 mph) or more, there is a 20% difference or greater in the average speed between the front wheels and rear wheels for 20 seconds or more.
·

Tire and wheel size

·

Tire deformation

·

Speed sensor rotor

·

Speed sensor

·

Speed sensor circuit

·

Skid control ECU (brake actuator assembly)



WIRING DIAGRAM

C296056E05
1.021,1.594 1.479,1.792 0.458,0.198 10 false A35 1.031,3.458 1.49,3.656 0.458,0.198 10 false A34 1.396,1.594 3.125,1.885 1.729,0.292 10 false Front Speed Sensor RH 1.385,3.458 2.979,3.802 1.594,0.344 10 false Front Speed Sensor LH 1.344,3.115 1.802,3.313 0.458,0.198 10 false FL+ 2.021,3.115 2.479,3.313 0.458,0.198 10 false FL- 1.354,1.25 1.813,1.448 0.458,0.198 10 false FR+ 1.979,1.25 2.438,1.448 0.458,0.198 10 false FR- 1.156,1.146 1.615,1.344 0.458,0.198 10 false 2 2.354,1.156 2.813,1.354 0.458,0.198 10 false 1 1.167,3.01 1.625,3.208 0.458,0.198 10 false 2 5.969,0.677 6.427,0.875 0.458,0.198 10 false FR+ 5.979,1.229 6.438,1.427 0.458,0.198 10 false FR- 2.344,3.01 2.802,3.208 0.458,0.198 10 false 1 5.969,2.552 6.427,2.75 0.458,0.198 10 false FL+ 5.979,3.104 6.438,3.302 0.458,0.198 10 false FL- 5.698,2.979 6.156,3.177 0.458,0.198 10 false 17 5.688,2.406 5.906,2.615 0.219,0.208 10 false 18 5.708,1.083 5.927,1.344 0.219,0.26 10 false 30 5.698,0.521 5.917,0.771 0.219,0.25 10 false 31 5.542,3.865 6.021,4.135 0.479,0.271 10 false A86 5.542,4.031 7.083,4.51 1.542,0.479 10 false Skid Control ECU (Brake Actuator Assembly)

C296057E07
0.813,1.031 1.271,1.229 0.458,0.198 10 false RR+ 0.823,3.365 1.281,3.563 0.458,0.198 10 false RR- 0.854,5.708 1.313,5.906 0.458,0.198 10 false RL- 0.844,5.146 1.302,5.344 0.458,0.198 10 false RL+ 0.833,1.594 1.292,1.792 0.458,0.198 10 false RR- 0.813,2.781 1.271,2.979 0.458,0.198 10 false RR+ 1.594,2.781 2.052,2.979 0.458,0.198 10 false RR+ 1.99,2.781 2.448,2.979 0.458,0.198 10 false RR+ 5.917,1.031 6.375,1.229 0.458,0.198 10 false RR+ 2,3.365 2.458,3.563 0.458,0.198 10 false RR- 1.594,3.365 2.052,3.563 0.458,0.198 10 false RR- 5.917,1.583 6.375,1.781 0.458,0.198 10 false RR- 1.188,0.927 1.646,1.125 0.458,0.198 10 false 2 1.188,1.5 1.646,1.698 0.458,0.198 10 false 1 1.271,2.771 1.729,2.969 0.458,0.198 10 false o1 2.385,2.771 2.844,2.969 0.458,0.198 10 false Oo1 1.271,3.354 1.729,3.552 0.458,0.198 10 false o1 2.385,3.354 2.844,3.552 0.458,0.198 10 false Oo1 0.844,7.469 1.302,7.667 0.458,0.198 10 false RL- 1.594,7.479 2.052,7.677 0.458,0.198 10 false RL- 2.021,7.479 2.479,7.677 0.458,0.198 10 false RL- 5.906,5.719 6.365,5.917 0.458,0.198 10 false RL- 0.823,6.896 1.281,7.094 0.458,0.198 10 false RL+ 1.594,6.896 2.052,7.094 0.458,0.198 10 false RL+ 1.99,6.896 2.448,7.094 0.458,0.198 10 false RL+ 5.906,5.167 6.365,5.365 0.458,0.198 10 false RL+ 1.177,5.042 1.635,5.24 0.458,0.198 10 false 3 1.177,5.604 1.635,5.802 0.458,0.198 10 false 1 1.292,6.885 1.75,7.083 0.458,0.198 10 false r1 1.292,7.469 1.75,7.667 0.458,0.198 10 false r1 2.396,6.885 2.854,7.083 0.458,0.198 10 false Or1 2.385,7.469 2.844,7.667 0.458,0.198 10 false Or1 0.188,2.042 0.646,2.24 0.458,0.198 10 false O3 0.521,2.042 1.313,2.438 0.792,0.396 10 false Rear Speed Sensor RH 0.385,3.813 1.177,4.208 0.792,0.396 10 false Rear Speed Sensor RH 1.552,3.813 2.385,4.365 0.833,0.552 10 false Skid Control Sensor Wire RH 1.542,7.917 2.365,8.458 0.823,0.542 10 false Skid Control Sensor Wire LH 0.479,6.135 1.271,6.531 0.792,0.396 10 false Rear Speed Sensor LH 0.385,7.927 1.177,8.323 0.792,0.396 10 false Rear Speed Sensor LH 0.177,6.135 0.635,6.333 0.458,0.198 10 false O2 3.177,2.688 3.635,2.885 0.458,0.198 10 false *2 2.802,0.927 3.26,1.125 0.458,0.198 10 false *1 2.813,1.5 3.271,1.698 0.458,0.198 10 false *1 3.479,3.25 3.938,3.448 0.458,0.198 10 false *2 2.552,5.031 3.01,5.229 0.458,0.198 10 false *1 2.552,5.604 3.01,5.802 0.458,0.198 10 false *1 3.177,6.813 3.635,7.01 0.458,0.198 10 false *2 3.5,7.375 3.958,7.573 0.458,0.198 10 false *2 5.615,0.875 5.844,1.104 0.229,0.229 10 false 16 5.615,1.458 5.885,1.708 0.271,0.25 10 false 15 5.635,4.99 5.927,5.25 0.292,0.26 10 false 29 5.635,5.563 5.927,5.875 0.292,0.313 10 false 28 5.469,7.938 5.927,8.135 0.458,0.198 10 false A86 5.469,8.125 7.052,8.542 1.583,0.417 10 false Skid Control ECU (Brake Actuator Assembly) 3.219,8.063 4.448,8.354 1.229,0.292 10 false *1: for AWD 3.219,8.427 4.417,8.76 1.198,0.333 10 false *2: for 2WD 1.292,3.156 1.75,3.354 0.458,0.198 10 false 1 1.292,2.573 1.75,2.771 0.458,0.198 10 false 2 2.469,2.573 2.927,2.771 0.458,0.198 10 false 2 2.458,3.146 2.917,3.344 0.458,0.198 10 false 1 1.302,6.688 1.76,6.885 0.458,0.198 10 false 2 2.469,7.271 2.927,7.469 0.458,0.198 10 false 1 1.292,7.271 1.75,7.469 0.458,0.198 10 false 1 2.458,6.688 2.917,6.885 0.458,0.198 10 false 3

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK TIRES
a.

Check the size and condition of all four wheels.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION

HINT:

The DTC is output when tire deformation or a difference in tire size is detected.


OK:

The diameter of all four tires and the tire pressure are the same.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (SPEED SENSOR)

NG

REPLACE TIRES SO THAT ALL FOUR TIRES ARE SAME SIZE

2.READ VALUE USING GTS (SPEED SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Select the Data List using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
50003 105 1,2,3,4

d.

Check the speed value output from the speed sensor displayed on the GTS.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION


OK:

The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.



Result:
Result Proceed to
OK A
NG (for front) B
NG (for rear 2WD) C
NG (for rear AWD) D



A

3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)

B

4.CHECK FRONT SPEED SENSOR AND SENSOR ROTOR

C

12.INSPECT SKID CONTROL SENSOR WIRE

D

18.CHECK REAR SPEED SENSOR AND SENSOR ROTOR
3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
a.

Turn the ignition switch off.


b.

Perform the sensor check using the Test Mode procedure.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE

OK:

All Test Mode DTCs are not output.


Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 3

Result:
Result Proceed to
OK A
NG (for front) B
NG (for rear 2WD) C
NG (for rear AWD) D



A

B

4.CHECK FRONT SPEED SENSOR AND SENSOR ROTOR

C

12.INSPECT SKID CONTROL SENSOR WIRE

D

18.CHECK REAR SPEED SENSOR AND SENSOR ROTOR
4.CHECK FRONT SPEED SENSOR AND SENSOR ROTOR
a.

Turn the ignition switch off.


b.

Remove the front speed sensor and the component with the sensor rotor.

for speed sensor: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL

for sensor rotor (for 1AR-FE): Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY(for 1AR-FE)>REMOVAL

for sensor rotor (for 2GR-FKS): Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY(for 2GR-FKS)>REMOVAL


c.

Check the speed sensor tip and speed sensor rotor.

OK:

No scratches, oil, or foreign matter on the sensor tip and rotor.


NOTICE:
·

If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.

If there are any ferrous metal filings stuck to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign matter before replacing the sensor.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE




Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR OR COMPONENT WITH SENSOR ROTOR

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A86 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the A35 or A34 front speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A86-31 (FR+) - A35-2 (FR+) Always Below 1 Ω
A86-31 (FR+) or A35-2 (FR+) - Body ground Always 10 kΩ or higher
A86-30 (FR-) - A35-1 (FR-) Always Below 1 Ω
A86-30 (FR-) or A35-1 (FR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A86-18 (FL+) - A34-2 (FL+) Always Below 1 Ω
A86-18 (FL+) or A34-2 (FL+) - Body ground Always 10 kΩ or higher
A86-17 (FL-) - A34-1 (FL-) Always Below 1 Ω
A86-17 (FL-) or A34-1 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)
a.
C156480C36
2.365,1.292 2.719,1.531 0.354,0.24 0.802,1.292 1.156,1.531 0.354,0.24 1.208,2.833 1.063,2.281 false 2.927,2.813 2.646,2.281 false 0.125,0.083 0.583,0.281 0.458,0.198 10 false *a 0.875,1.323 1.333,1.521 0.458,0.198 10 false A35 2.427,1.323 2.885,1.521 0.458,0.198 10 false A34 2.844,2.875 3.302,3.073 0.458,0.198 10 false FL+ 1.146,2.875 1.604,3.073 0.458,0.198 10 false FR+ 0.292,0.917 0.75,1.115 0.458,0.198 12 false *A 1.917,0.917 2.375,1.115 0.458,0.198 12 false *B
*A RH
*B LH
*a Front view of wire harness connector
(to Front Speed Sensor)


Reconnect the A86 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Condition Specified Condition
A35-2 (FR+) - Body ground Ignition switch ON 5.7 to 14 V

for LH
Tester Connection Condition Specified Condition
A34-2 (FL+) - Body ground Ignition switch ON 5.7 to 14 V


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

7.RECONFIRM DTC

NG

7.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Reconnect the A35 or A34 front speed sensor connector.


c.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

d.

Turn the ignition switch off.


e.

Start the engine.


f.

Perform a road test.


g.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1337 is output. A
DTC C1337 is not output. B



A

8.REPLACE SPEED SENSOR FRONT RH

B

8.REPLACE SPEED SENSOR FRONT RH
a.

Turn the ignition switch off.


b.

Result:
Proceed to
NEXT



NEXT

9.RECONFIRM DTC
9.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Perform a road test.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1337 is output. A
DTC C1337 is not output. B



A

10.REPLACE FRONT DRIVE SHAFT ASSEMBLY

B

END

10.REPLACE FRONT DRIVE SHAFT ASSEMBLY
a.

Turn the ignition switch off.


b.

Replace the front speed sensor rotor (front drive shaft assembly).

for 1AR-FE: Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY(for 1AR-FE)>REMOVAL

for 2GR-FKS: Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY(for 2GR-FKS)>REMOVAL

NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


HINT:

If the front speed sensor rotor needs to be replaced, replace the front drive shaft assembly.



Result:
Proceed to
NEXT



NEXT

11.RECONFIRM DTC
11.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Perform a road test.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1337 is output. A
DTC C1337 is not output. B



A

B

END

12.INSPECT SKID CONTROL SENSOR WIRE
a.
C296046C01
0.844,2.667 1.167,2.833 0.323,0.167 0.854,0.333 1.177,0.5 0.323,0.167 2.344,0.583 2.667,0.75 0.323,0.167 2.219,2.833 2.542,3 0.323,0.167 0.5,1.833 0.5,1.5 0.5,1.5 0.906,1.135 false 0.5,4.25 0.5,3.833 0.5,3.833 0.917,3.448 false 2,1.833 2,1.583 2,1.583 2.302,1.333 false 1.917,4.25 1.917,3.917 1.917,3.917 2.167,3.615 false 1.583,1.833 1.583,1.5 1.583,1.5 1.156,1.135 false 1.5,4.25 1.5,3.833 1.5,3.833 1.177,3.448 false 3,1.833 3,1.583 3,1.583 2.698,1.344 false 2.917,4.25 2.917,3.917 2.917,3.917 2.635,3.604 false 1.49,1.865 1.948,2.063 0.458,0.198 10 false RR+ 1.917,1.865 2.375,2.063 0.458,0.198 10 false RR+ 2.917,1.875 3.375,2.073 0.458,0.198 10 false RR- 0.417,1.865 0.875,2.063 0.458,0.198 10 false RR- 0.427,4.292 0.885,4.49 0.458,0.198 10 false RL- 1.417,4.292 1.875,4.49 0.458,0.198 10 false RL+ 1.833,4.281 2.292,4.479 0.458,0.198 10 false RL+ 2.844,4.281 3.302,4.479 0.458,0.198 10 false RL- 0.115,0.052 0.427,0.25 0.313,0.198 10 false *a 0.958,0.333 1.271,0.531 0.313,0.198 10 false o1 2.281,2.844 2.594,3.042 0.313,0.198 10 false Or1 0.958,2.667 1.271,2.865 0.313,0.198 10 false r1 2.385,0.583 2.698,0.781 0.313,0.198 10 false Oo1 0.177,0.51 0.49,0.708 0.313,0.198 12 false *A 0.188,2.802 0.5,3 0.313,0.198 12 false *B 0.927,1.948 1.24,2.146 0.313,0.198 10 false *b 2.417,1.948 2.729,2.146 0.313,0.198 10 false *c 0.938,4.365 1.25,4.563 0.313,0.198 10 false *b 2.323,4.365 2.635,4.563 0.313,0.198 10 false *c
*A RH
*B LH
*a Front view of Skid Control Sensor Wire
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Remove the skid control sensor wire.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
o1-2 (RR+) - Oo1-2 (RR+) Always Below 1 Ω
o1-2 (RR+) - Oo1-1 (RR-) Always 10 kΩ or higher
o1-2 (RR+) or Oo1-2 (RR+) - Body ground Always 10 kΩ or higher
o1-1 (RR-) - Oo1-1 (RR-) Always Below 1 Ω
o1-1 (RR-) - Oo1-2 (RR+) Always 10 kΩ or higher
o1-1 (RR-) or Oo1-1 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
r1-2 (RL+) - Or1-3 (RL+) Always Below 1 Ω
r1-2 (RL+) - Or1-1 (RL-) Always 10 kΩ or higher
r1-2 (RL+) or Or1-3 (RL+) - Body ground Always 10 kΩ or higher
r1-1 (RL-) - Or1-1 (RL-) Always Below 1 Ω
r1-1 (RL-) - Or1-3 (RL+) Always 10 kΩ or higher
r1-1 (RL-) or Or1-1 (RL-) - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE)

NG

13.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A86 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A86-16 (RR+) - Oo1-2 (RR+) Always Below 1 Ω
A86-16 (RR+) or Oo1-2 (RR+) - Body ground Always 10 kΩ or higher
A86-15 (RR-) - Oo1-1 (RR-) Always Below 1 Ω
A86-15 (RR-) or Oo1-1 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A86-29 (RL+) - Or1-3 (RL+) Always Below 1 Ω
A86-29 (RL+) or Or1-3 (RL+) - Body ground Always 10 kΩ or higher
A86-28 (RL-) - Or1-1 (RL-) Always Below 1 Ω
A86-28 (RL-) or Or1-1 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)
a.
C205828C05
0.75,0.906 1.083,1.083 0.333,0.177 2.354,0.906 2.688,1.083 0.333,0.177 1.094,1.823 1.417,2.417 false 2.667,1.76 3,2.417 false 0.104,0.073 0.292,0.26 0.188,0.188 10 false *a 0.802,0.906 1.333,1.177 0.531,0.271 10 false Oo1 2.417,0.906 2.917,1.198 0.5,0.292 10 false Or1 1.323,2.469 1.656,2.656 0.333,0.188 10 false RR+ 2.917,2.469 3.25,2.656 0.333,0.188 10 false RL+ 0.25,0.729 0.646,1.073 0.396,0.344 12 false *A 1.917,0.729 2.26,1.188 0.344,0.458 12 false *B
*A RH
*B LH
*a Front view of wire harness connector
(to Skid Control Sensor Wire)


Reconnect the A86 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Condition Specified Condition
Oo1-2 (RR+) - Body ground Ignition switch ON 5.7 to 14 V

for LH
Tester Connection Condition Specified Condition
Or1-3 (RL+) - Body ground Ignition switch ON 5.7 to 14 V


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

15.RECONFIRM DTC

NG

15.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Install the skid control sensor wire.


c.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

d.

Turn the ignition switch off.


e.

Start the engine.


f.

Perform a road test.


g.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1337 is output. A
DTC C1337 is not output. B



A

16.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY WITH REAR SPEED SENSOR

B

16.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY WITH REAR SPEED SENSOR
a.

Turn the ignition switch off.


b.

Replace the rear speed sensor rotor (rear axle hub and bearing assembly) with rear speed sensor.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR(for 2WD)>REMOVAL

NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


HINT:

The rear speed sensor rotor and rear speed sensor are incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly with rear speed sensor.



Result:
Proceed to
NEXT



NEXT

17.RECONFIRM DTC
17.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Perform a road test.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1337 is output. A
DTC C1337 is not output. B



A

B

END

18.CHECK REAR SPEED SENSOR AND SENSOR ROTOR
a.

Turn the ignition switch off.


b.

Remove the rear speed sensor and the component with the sensor rotor.

for speed sensor: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR(for AWD)>REMOVAL

for sensor rotor: Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL


c.

Check the speed sensor tip and speed sensor rotor.

OK:

No scratches, oil, or foreign matter on the sensor tip and rotor.


NOTICE:
·

If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.

If there are any ferrous metal filings stuck to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign matter before replacing the sensor.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE




Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)

NG

CLEAN OR REPLACE REAR SPEED SENSOR OR COMPONENT WITH SENSOR ROTOR

19.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)
a.

Install the rear speed sensor and the component with the sensor rotor.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A86 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the O3 or O2 rear speed sensor connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A86-16 (RR+) - O3-2 (RR+) Always Below 1 Ω
A86-16 (RR+) or O3-2 (RR+) - Body ground Always 10 kΩ or higher
A86-15 (RR-) - O3-1 (RR-) Always Below 1 Ω
A86-15 (RR-) or O3-1 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A86-29 (RL+) - O2-3 (RL+) Always Below 1 Ω
A86-29 (RL+) or O2-3 (RL+) - Body ground Always 10 kΩ or higher
A86-28 (RL-) - O2-1 (RL-) Always Below 1 Ω
A86-28 (RL-) or O2-1 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

20.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)
a.
C205828C04
0.75,0.906 1.083,1.083 0.333,0.177 2.354,0.906 2.688,1.083 0.333,0.177 1.094,1.823 1.417,2.417 false 2.667,1.76 3,2.417 false 0.104,0.073 0.292,0.26 0.188,0.188 10 false *a 0.823,0.906 1.354,1.177 0.531,0.271 10 false O3 2.427,0.906 2.927,1.198 0.5,0.292 10 false O2 1.323,2.469 1.656,2.656 0.333,0.188 10 false RR+ 2.917,2.469 3.25,2.656 0.333,0.188 10 false RL+ 0.25,0.729 0.646,1.073 0.396,0.344 12 false *A 1.917,0.729 2.26,1.188 0.344,0.458 12 false *B
*A RH
*B LH
*a Front view of wire harness connector
(to Rear Speed Sensor)


Reconnect the A86 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Condition Specified Condition
O3-2 (RR+) - Body ground Ignition switch ON 5.7 to 14 V

for LH
Tester Connection Condition Specified Condition
O2-3 (RL+) - Body ground Ignition switch ON 5.7 to 14 V


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

21.RECONFIRM DTC

NG

21.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Reconnect the O3 or O2 rear speed sensor connector.


c.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

d.

Turn the ignition switch off.


e.

Start the engine.


f.

Perform a road test.


g.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1337 is output. A
DTC C1337 is not output. B



A

22.REPLACE REAR SPEED SENSOR

B

22.REPLACE REAR SPEED SENSOR
a.

Turn the ignition switch off.



Result:
Proceed to
NEXT



NEXT

23.RECONFIRM DTC
23.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Perform a road test.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1337 is output. A
DTC C1337 is not output. B



A

24.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

B

END

24.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY
a.

Turn the ignition switch off.


b.

Replace the rear speed sensor rotor (rear axle hub and bearing assembly).

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL

NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


HINT:

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly.



Result:
Proceed to
NEXT



NEXT

25.RECONFIRM DTC
25.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Perform a road test.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1337 is output. A
DTC C1337 is not output. B



A

B

END