Home › Engine / Hybrid System › 1AR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.11
RM3160E _51 Engine / Hybrid System _019671 1AR-FE ENGINE CONTROL _0103543 SFI SYSTEM J

1AR-FE ENGINE CONTROL  SFI SYSTEM  Fuel Pump Control Circuit  


DESCRIPTION

When the engine is cranked, the starter (ST) relay drive signal output from the ignition switch assembly*1 or certification ECU (smart key ECU assembly)*2 is input into the STA terminal of the ECM, and the NE signal generated by the crankshaft position sensor is input into the NE+ terminal. The ECM interprets that the engine is being cranked, and turns transistor Tr1 in the ECM internal circuit on. Current flows to the C/OPN (Circuit Opening) relay by turning Tr1 on. Then, the fuel pump operates.

While the NE signal is input into the ECM with the engine running, the ECM turns Tr1 on continuously.

*1: w/o Smart Entry and Start System.

*2: w/ Smart Entry and Start System.

WIRING DIAGRAM

A317488E03
0.49,2.323 0.802,2.521 0.313,0.198 10 false *1 0.521,1.406 0.833,1.604 0.313,0.198 10 false ST 3.583,0.406 3.896,0.604 0.313,0.198 10 false *1 4.958,0.417 5.271,0.615 0.313,0.198 10 false *2 5.656,6.698 5.969,6.896 0.313,0.198 10 false 21 1.583,0.427 1.896,0.625 0.313,0.198 10 false 4 2.771,0.427 3.083,0.625 0.313,0.198 10 false 3 5.479,0.417 5.792,0.615 0.313,0.198 10 false 3 1.958,8.229 2.271,8.427 0.313,0.198 10 false 5 5.698,0.531 6.313,0.729 0.615,0.198 10 false IG1D 5.385,1.042 5.719,1.219 0.333,0.177 10 false F10 1.406,0.781 1.74,0.958 0.333,0.177 10 false F50 1.771,0.438 2.167,0.667 0.396,0.229 10 false AM2 2.448,0.427 2.844,0.656 0.396,0.229 10 false IG2 1.406,0.927 3.198,1.188 1.792,0.26 10 false Ignition Switch Assembly*1 1.906,1.802 2.583,2.021 0.677,0.219 10 false IG2-MAIN 1.906,3.24 2.583,3.458 0.677,0.219 10 false EFI-MAIN 3.167,3.771 3.844,3.99 0.677,0.219 10 false EFI MAIN 3.917,4.542 4.594,4.76 0.677,0.219 10 false EFI NO. 2 1.365,2.906 1.677,3.104 0.313,0.198 10 false 1 4.365,1.177 4.677,1.375 0.313,0.198 10 false 1 1.938,7.292 2.25,7.49 0.313,0.198 10 false 4 1.365,3.094 1.656,3.271 0.292,0.177 10 false B 1.948,4.917 2.604,5.135 0.656,0.219 10 false A/F HTR 3.344,5.104 3.646,5.313 0.302,0.208 10 false A/F 4.417,1.406 4.708,1.583 0.292,0.177 10 false 1E 3.365,2.313 3.656,2.49 0.292,0.177 10 false IG2 4.219,5.354 4.51,5.531 0.292,0.177 10 false 1F 5.656,3.354 5.948,3.531 0.292,0.177 10 false 46 4.875,2.406 5.188,2.844 0.313,0.438 10 false IG2-EFI 4.969,3.458 5.26,3.635 0.292,0.177 10 false 1G 5.031,3.271 5.344,3.469 0.313,0.198 10 false 6 5.927,3.458 6.479,3.688 0.552,0.229 10 false MREL 5.375,1.198 6.896,1.625 1.521,0.427 10 false Certification ECU (Smart Key ECU Assembly)*2 4.344,5.146 4.656,5.344 0.313,0.198 10 false 1 3.823,6.167 4.135,6.365 0.313,0.198 10 false 1 3.063,6.177 3.375,6.375 0.313,0.198 10 false 2 3.063,5.75 3.375,5.948 0.313,0.198 10 false 3 4.885,5.156 5.198,5.354 0.313,0.198 10 false 4 3.833,5.75 4.146,5.948 0.313,0.198 10 false 5 4.719,5.354 5.01,5.531 0.292,0.177 10 false 1G 3.25,6.604 3.802,6.833 0.552,0.229 10 false C/OPN 0.802,5.573 3.25,5.833 2.448,0.26 10 false Semiconductor Pwr Integration ECU 2.438,7.656 2.729,7.833 0.292,0.177 10 false M9 2.438,7.802 3.25,8.167 0.813,0.365 10 false Fuel Pump 0.677,7.917 1.281,8.167 0.604,0.25 10 false Battery 0.521,6.417 1.125,6.667 0.604,0.25 10 false FL MAIN 5.917,6.708 6.229,6.906 0.313,0.198 10 false FC 6.406,6.083 6.719,6.281 0.313,0.198 10 false Tr1 6.313,7.969 6.74,8.167 0.427,0.198 10 false ECM 6.01,7.969 6.323,8.167 0.313,0.198 10 false A43 3.375,7.875 5.823,8.115 2.448,0.24 10 false *1: w/o Smart Entry and Start System 3.375,8.229 5.823,8.469 2.448,0.24 10 false *2: w/ Smart Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

e.

Check whether the fuel pump operating sounds occurs when performing the Active Test on the GTS.


Result:
Result Proceed to
Fuel pump operating sound does not occur A
Fuel pump operating sound occurs B



A

2.INSPECT CIRCUIT OPENING RELAY (C/OPN RELAY)

B

8.READ VALUE USING GTS (STARTER SIGNAL)
2.INSPECT CIRCUIT OPENING RELAY (C/OPN RELAY)

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - C/OPN RELAY)

NG

REPLACE RELAY (C/OPN RELAY)

3.CHECK HARNESS AND CONNECTOR (ECM - C/OPN RELAY)
a.

Disconnect the ECM connector.


b.

Remove the C/OPN relay from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A43-21 (FC) - 2 (C/OPN relay) Always Below 1 Ω
A43-21 (FC) or 2 (C/OPN relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - C/OPN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - C/OPN RELAY)
a.

Disconnect the semiconductor pwr integration ECU connector.


b.

Remove the C/OPN relay from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1G-4 - 1 (C/OPN relay) Always Below 1 Ω
1F-1 - 5 (C/OPN relay) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - FUEL PUMP - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - FUEL PUMP - BODY GROUND)
a.

Remove the C/OPN relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Disconnect the fuel pump connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (C/OPN relay) - M9-4 Always Below 1 Ω
M9-5 - Body ground Always Below 1 Ω
3 (C/OPN relay) or M9-4 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT FUEL PUMP
a.

Inspect the fuel pump.

Click hereEngine / Hybrid System>1AR-FE FUEL>FUEL PUMP>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

7.INSPECT SEMICONDUCTOR PWR INTEGRATION ECU

NG

7.INSPECT SEMICONDUCTOR PWR INTEGRATION ECU
a.

Inspect the semiconductor pwr integration ECU.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE SEMICONDUCTOR PWR INTEGRATION ECU

8.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the result when the ignition switch is ON and the engine starts.

OK:
Condition Starter Signal
Ignition switch ON OFF
Cranking ON



Result:
Proceed to
OK
NG



OK

9.READ VALUE USING GTS (ENGINE SPEED)

NG

9.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 234 9

e.

Read the values displayed on the GTS while cranking.

OK:

Values are displayed continuously.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

CHECK CRANKSHAFT POSITION SENSOR CIRCUIT