Refer to DTCs C1413 and C1414.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1413
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1401 | Front Speed Sensor RH Malfunction | Any of the following is detected:
1.
At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more (for 2WD). 2.
At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 30 seconds or more (for AWD). 3.
At a vehicle speed less than 10 km/h (6 mph), output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more. 4.
At a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more (for 2WD). 5.
At a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 30 seconds or more (for AWD). |
·
Front speed sensor RH ·
Sensor installation ·
Front speed sensor rotor RH (front drive shaft assembly RH) |
| C1402 | Front Speed Sensor LH Malfunction | Any of the following is detected:
1.
At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more (for 2WD). 2.
At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 30 seconds or more (for AWD). 3.
At a vehicle speed less than 10 km/h (6 mph), output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more. 4.
At a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more (for 2WD). 5.
At a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 30 seconds or more (for AWD). |
·
Front speed sensor LH ·
Sensor installation ·
Front speed sensor rotor LH (front drive shaft assembly LH) |
Even after the trouble areas are repaired, the ABS warning light will not go off unless the following operations are performed:
Drive the vehicle at 30 km/h (19 mph) for 30 seconds or more and check that the ABS warning light goes off.
Clear the DTCs.
DTC C1401 is for the front speed sensor RH.
DTC C1402 is for the front speed sensor LH.
| *1 | Front Speed Sensor |
| *a | Correct |
| *b | Incorrect |
| *c | 8.5 N*m |
| *d | No clearance |
Check the speed sensor installation.
There is no clearance between the sensor and the front steering knuckle.
The installation bolt is tightened properly.
8.5 N*m (87 kgf*cm, 75 in.*lbf)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front speed sensor and the component with the sensor rotor.
for speed sensor: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL
for sensor rotor (for 1AR-FE): Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY(for 1AR-FE)>REMOVAL
for sensor rotor (for 2GR-FKS): Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY(for 2GR-FKS)>REMOVAL
Check the speed sensor tip and speed sensor rotor.
No scratches, oil, or foreign matter on the sensor tip and rotor.
If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.
If there are any ferrous metal filings stuck to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign matter before replacing the sensor.
Check the speed sensor signal after cleaning or replacement.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Install the front speed sensor and the component with the sensor rotor.
Connect the GTS to the DLC3.
Start the engine.
Select the Data List using the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Wheel Speed | Front wheel speed sensor RH reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front wheel speed sensor LH reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| FR Wheel Speed |
| FL Wheel Speed |
Check the speed value output from the speed sensor displayed on the GTS.
Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION
The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.
Check the speed sensor signal after replacement.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Turn the ignition switch off.
Replace the front speed sensor.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL
Check the speed sensor signal after replacement.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Perform a road test.
Check if the same DTC is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs C1401 and C1402 are not output. | A |
| DTCs C1401 and/or C1402 are output. | B |
Check the speed sensor signal after replacement.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
If the front speed sensor rotor needs to be replaced, replace the front drive shaft assembly.
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.
A
B
for 1AR-FE: Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY(for 1AR-FE)>REMOVAL
for 2GR-FKS: Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY(for 2GR-FKS)>REMOVAL