Home › Drivetrain › UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE ASSEMBLY(When Not Using the Engine Support Bridge) › 2016.11–2018.09
RM3160E _52 Drivetrain _060165 UA80F AUTOMATIC TRANSMISSION / TRANSAXLE _0303763 AUTOMATIC TRANSAXLE ASSEMBLY(When Not Using the Engine Support Bridge) A

UA80F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE ASSEMBLY(When Not Using the Engine Support Bridge)  INSTALLATION  


PROCEDURE

Hide 32000 1.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C361056C01
0.604,1.781 0.917,1.438 true 0.635,0.427 0.875,0.885 true 2.115,0.208 2.813,0.188 true 0.448,0.281 0.76,0.479 0.313,0.198 10 true *b 0.417,1.688 0.729,1.885 0.313,0.198 10 true *b 2.885,0.052 3.198,0.25 0.313,0.198 10 true *a
*a Matchmark
*b Key


Turn the front oil pump drive gear so that either key is at the top and place a matchmark on the transaxle housing to indicate the position of the key.


b.
C361055C01
1.167,0.292 1.604,0.615 false 1.729,1.583 2.167,1.906 false 0.979,0.125 1.292,0.323 0.313,0.198 10 false *a 2.229,1.885 2.542,2.083 0.313,0.198 10 false *b
*a Groove
*b Matchmark
V100135

MP Grease


Place a matchmark on the torque converter assembly so that the position of its groove is clearly indicated.


c.
C363765C01
0.573,0.271 1.271,0.74 true 0.583,0.281 1.25,0.573 false 2.333,0.917 2.906,0.708 true 2.344,1.198 2.906,0.708 true 0.406,0.146 0.719,0.344 0.313,0.198 10 false *a 2.948,0.573 3.26,0.771 0.313,0.198 10 false *1
*1 Front Oil Pump Oil Seal
*a Matchmark


Align the matchmark on the torque converter assembly with the one on the transaxle housing and engage the splines of the input shaft with the turbine runner splines.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




d.
C363766C01
0.74,0.281 1.344,0.448 true 0.76,2.01 1.344,1.594 true 2.323,0.854 2.917,0.677 true 2.333,1.167 2.906,0.677 true 0.552,0.135 0.802,0.344 0.25,0.208 10 false *a 0.583,1.906 0.833,2.115 0.25,0.208 10 false *a 2.938,0.531 3.188,0.74 0.25,0.208 10 false *1
*1 Front Oil Pump Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.

NOTICE:
·

Do not push the torque converter assembly excessively when rotating it.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




e.
C363767C01
0.604,0.271 1.26,0.615 true 0.646,0.292 1.26,0.458 true 2.281,0.833 2.896,0.677 true 2.302,1.167 2.885,0.677 true 0.417,0.125 0.729,0.323 0.313,0.198 10 false *a 2.927,0.531 3.24,0.729 0.313,0.198 10 false *1
*1 Front Oil Pump Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the transaxle housing and insert the keys of the front oil pump drive gear into the grooves of the torque converter assembly.

NOTICE:
·

Do not push the torque converter assembly excessively when rotating it.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




f.

Clean the drive plate and torque converter assembly setting bolt holes.


g.
C347941C01
2.375,0.969 2.375,0.729 2.375,0.729 2.531,0.729 false 2.438,1.729 2.438,1.479 2.438,1.479 2.688,1.479 false 0.75,0.333 1,0.333 1,0.333 1.25,0.969 true 0.969,2.979 0.969,2.396 true 2.302,0.979 2.615,1.135 0.313,0.156 10 false *a 2.385,1.75 2.698,1.906 0.313,0.156 10 false *b 2.177,0.292 2.333,0.49 0.156,0.198 10 false A 0.583,0.229 0.896,0.385 0.313,0.156 10 false *a 0.917,3 1.229,3.156 0.313,0.156 10 false *b
*a Engine Assembly Surface
*b Drive Plate and Ring Gear Sub-assembly Surface


Using a vernier caliper and straightedge, measure the dimension (A) between the automatic transaxle assembly contact surface of the engine assembly*a and the torque converter assembly contact surface of the drive plate and ring gear sub-assembly*b.

NOTICE:

Make sure to deduct the thickness of the straightedge.



h.
C363763C01
2.417,0.448 2.573,0.646 0.156,0.198 10 false B

Using a vernier caliper and straightedge, measure the dimension (B) shown in the illustration and check that the dimension (B) is more than the dimension (A), which was measured in the previous step.

Standard:

Dimension (A) + 1 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the automatic transaxle assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.

·

Do not include the thickness of the set block.




Hide 35104V 2.INSTALL BREATHER PLUG HOSE

a.

Install the breather plug sub-assembly to the breather plug hose.


b.

Install the breather plug hose to the No. 1 breather plug (ATM).


Hide 35150 3.INSTALL TRANSMISSION CASE PLUG ASSEMBLY

a.

Coat the O-ring of a new transmission case plug assembly with Toyota Genuine ATF WS.


b.

Install the transmission case plug assembly to the automatic transaxle assembly.


Hide 4.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket to the automatic transaxle case sub-assembly with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 5.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the automatic transaxle case sub-assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 12311A 6.INSTALL FRONT ENGINE MOUNTING BRACKET

a.

Install the front engine engine mounting bracket to the automatic transaxle assembly with the 4 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 12325A 7.INSTALL ENGINE MOUNTING BRACKET LH

a.

Install the engine engine mounting bracket LH to the automatic transaxle assembly with the 3 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 32907C 8.INSTALL NO. 1 OIL COOLER TUBE SUB-ASSEMBLY WITHOUT HOSE

Hide 32942 9.CONNECT OUTLET NO. 1 OIL COOLER HOSE

Hide 33493A 10.INSTALL TRANSMISSION OIL COOLER

Hide 11.CONNECT OUTLET NO. 3 OIL COOLER HOSE

Hide 16267H 13.CONNECT NO. 3 WATER BY-PASS HOSE

Hide 16281K 14.CONNECT NO. 4 WATER BY-PASS HOSE

Hide 16570 15.INSTALL RADIATOR PIPE ASSEMBLY

a.

Install the radiator pipe assembly to the automatic transaxle assembly with the bolt.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


b.

Install the No. 3 water by-pass hose and the No. 4 water by-pass hose to the radiator pipe assembly and slide the 2 clips to secure them.

C368935C03
4.729,0.625 4.917,0.354 false 4.813,0.615 4.927,0.354 false 4.063,2.208 4.177,1.948 false 4,2.208 4.188,1.938 false 2.719,0.677 3.01,0.406 3.01,0.406 3.188,0.406 false 3.021,1.26 3.25,1.26 false 2.969,1.427 3.208,1.583 3.208,1.583 3.51,1.583 false 4.979,0.26 5.292,0.458 0.313,0.198 10 false *b 4.25,1.844 4.563,2.042 0.313,0.198 10 false *b 5.021,0.813 5.333,1.01 0.313,0.198 10 false *a 4.281,2.385 4.594,2.583 0.313,0.198 10 false *a 3.698,1.99 4.01,2.188 0.313,0.198 10 false *c 3.698,2.302 4.01,2.5 0.313,0.198 10 false *c 4.438,0.396 4.75,0.594 0.313,0.198 10 false *c 4.448,0.667 4.76,0.865 0.313,0.198 10 false *c 3.26,0.323 3.573,0.521 0.313,0.198 10 false *1 3.344,1.167 3.656,1.365 0.313,0.198 10 false *2 3.594,1.5 3.906,1.698 0.313,0.198 10 false *3
*1 Radiator Pipe Assembly *2 No. 3 Water By-pass Hose
*3 No. 4 Water By-pass Hose - -
*a 2 to 7 mm (0.0787 to 0.276 in.) *b Paint Mark
*c 45° (Claw of Clip Location) - -


NOTICE:
·

Make sure to slide the No. 3 water by-pass hose and the No. 4 water by-pass hose until each contacts the hose stopper of the radiator pipe assembly.

·

Make sure to align the paint mark of each hose with the paint mark of each tube.




Hide 36100 16.INSTALL TRANSFER ASSEMBLY

Hide 30500 17.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY

a.
C363764C01
1.698,1.063 1.927,1.063 false 1.167,1 1.479,1.198 0.313,0.198 10 false *1 1.969,0.979 2.281,1.177 0.313,0.198 10 false *2
*1 Crankshaft
*2 Torque Converter Assembly Centerpiece
V100135

Clutch Spline Grease


Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

Clutch Spline Grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum Grease Amount:

Approximately 1 g (0.0353 oz)



b.
C290460C01
2.094,0.552 2.656,0.552 true 0.469,1.313 1.031,1.313 true 0.292,1.208 0.604,1.406 0.313,0.198 10 false *1 2.698,0.427 3.01,0.625 0.313,0.198 10 false *1
*1 Knock Pin


Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.


c.
C363759N01
1.229,0.208 1.542,0.406 0.313,0.198 10 false A 1.792,0.042 2.104,0.24 0.313,0.198 10 false A 2.656,0.167 2.969,0.365 0.313,0.198 10 false A 2.813,0.646 3.125,0.844 0.313,0.198 10 false A 2.813,0.667 3.125,0.865 0.313,0.198 10 false A 2.896,1.094 3.208,1.292 0.313,0.198 10 false A 2.802,1.521 3.115,1.719 0.313,0.198 10 false A 2.573,1.781 2.927,1.99 0.354,0.208 10 false C 2.01,1.917 2.365,2.125 0.354,0.208 10 false C 1.49,1.917 1.844,2.125 0.354,0.208 10 false C 1.01,1.708 1.177,1.906 0.167,0.198 10 true B 0.823,0.75 0.99,0.948 0.167,0.198 10 true A

While keeping the engine assembly and automatic transaxle assembly horizontal, align the knock pins with the holes in the automatic transaxle assembly and install the automatic transaxle assembly with the 11 bolts shown in the illustration.

Torque:
Bolt (A) : 64 N*m (653 kgf*cm, 47 ft.*lbf)
Bolt (B) : 46 N*m (469 kgf*cm, 34 ft.*lbf)
Bolt (C) : 43 N*m (438 kgf*cm, 32 ft.*lbf)

Bolt Length:
Bolt Length
(A) 55 mm (2.17 in.)
(B) 41 mm (1.61 in.)
(C) 33 mm (1.30 in.)


NOTICE:
·

Confirm that the knock pins are installed to the automatic transaxle assembly contact surface of the cylinder block sub-assembly before installing the automatic transaxle assembly.

·

Do not forcibly pry on the automatic transaxle assembly.

·

Check that the torque converter assembly rotates.




Hide 36118A 18.INSTALL TRANSFER STIFFENER PLATE RH

a.
C296629C05
0.344,1.073 0.5,1.271 0.156,0.198 10 true A 0.49,0.656 0.646,0.854 0.156,0.198 10 true A 2.823,0.51 2.979,0.708 0.156,0.198 10 true B 3.01,1.26 3.167,1.458 0.156,0.198 10 true B

Temporarily install the transfer stiffener plate RH to the transfer case sub-assembly and rear engine mounting bracket with the 2 bolts (A) and 2 bolts (B).

HINT:
Bolt Length
·

Bolt (A): 35 mm (1.38 in.)

·

Bolt (B): 75 mm (2.95 in.)




b.

Tighten the 2 bolts (A).

Torque:
34 N*m (347 kgf*cm, 25 ft.*lbf)


c.

Tighten the 2 bolts (B) to install the transfer stiffener plate RH.

Torque:
78 N*m (795 kgf*cm, 58 ft.*lbf)


Hide 17118 19.INSTALL MANIFOLD STAY

a.
A370439C05
0,0 0,0 false
V100135

Bolt
V100136C11
0,0 0,0 false

Nut


Install the bolt and nut in the order shown in the illustration.

Torque:
Bolt : 34 N*m (347 kgf*cm, 25 ft.*lbf)
Nut : 35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide 48824A 25.INSTALL FRONT NO. 1 STABILIZER BRACKET RH

HINT:

Use the same procedure as for the LH side.


Hide 26.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

Hide 35104V 27.INSTALL BREATHER PLUG HOSE

a.

Engage the 3 hose clamps to install the breather plug hose.


Hide 82121 28.CONNECT ENGINE WIRE

a.
C368946C01
0.823,2.958 1.063,3.167 0.24,0.208 10 true *a 0.896,1.656 1.135,1.865 0.24,0.208 10 true *b 1.125,2.063 1.313,2.271 0.188,0.208 10 true A 1.865,1.052 2,1.229 0.135,0.177 10 true B
*a Transmission Wire Connector
*b Park/Neutral Position Switch Assembly Connector
V100135

Bolt
V100136

Nut


Connect the engine wire to the automatic transaxle case sub-assembly with the 2 bolts and nut.

Torque:
Bolt (A) : 25.5 N*m (260 kgf*cm, 19 ft.*lbf)
Bolt (B) : 19.1 N*m (195 kgf*cm, 14 ft.*lbf)
Nut : 8.5 N*m (87 kgf*cm, 75 in.*lbf)


b.

Connect the park/neutral position switch connector.


c.

Connect the connector of the transmission wire connector and rotate the lever to engage the claw.

HINT:

Rotate the lever until the claw of the transmission wire connector makes a click sound.



Hide 32101A 29.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.

Remove any remaining adhesive from the 6 drive plate and torque converter assembly setting bolts.


b.
P000601C22
1.979,1.177 2.177,0.229 2.177,0.229 2.302,0.229 false 2.323,0.135 2.521,0.323 0.198,0.188 10 false *a
*a Adhesive


Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 6 drive plate and torque converter assembly setting bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Make sure to install the 6 drive plate and torque converter assembly setting bolts immediately after applying adhesive to prevent foreign matter from attaching to them.



c.

Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)

NOTICE:

First install the black colored drive plate and torque converter assembly setting bolt, and then the remaining 5 silver colored drive plate and torque converter assembly setting bolts.



Hide 11361J 30.INSTALL FLYWHEEL HOUSING UNDER COVER

Hide 31.CHECK AUTOMATIC TRANSAXLE SYSTEM

NOTICE:

If automatic transaxle parts have been replaced, refer to Parts Replacement Compensation Table to determine if any additional operations are necessary.

Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION