Home › Engine / Hybrid System › 1AR-FE (ENGINE MECHANICAL) › CAMSHAFT › from 2016.11
RM3160E _51 Engine / Hybrid System _019672 1AR-FE ENGINE MECHANICAL _0109590 CAMSHAFT A

1AR-FE ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.REMOVE FRONT WHEEL RH

Hide 51441 4.REMOVE NO. 1 ENGINE UNDER COVER

Hide 53875A 5.SEPARATE FRONT FENDER LINER RH

Hide 53736 6.REMOVE FRONT FENDER APRON SEAL RH

Hide 53299D 7.REMOVE RADIATOR SIDE DEFLECTOR SEAL LH

Hide 53298E 8.REMOVE RADIATOR SIDE SEAL RH

Hide 53295E 9.REMOVE COOL AIR INTAKE DUCT SEAL

Hide 12601B 10.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 17750A 11.REMOVE INLET AIR CLEANER ASSEMBLY

Hide 17705 12.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17801 13.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17701 14.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 12327A 15.REMOVE NO. 2 ENGINE MOUNTING STAY RH

Hide 12363A 16.REMOVE ENGINE MOVING CONTROL ROD

Hide 82121 17.DISCONNECT ENGINE WIRE

a.
A283849

Disengage the 2 claws and disconnect the inlet heater water hose and outlet heater water hose.


b.

Disconnect the 12 connectors and 5 clamps.

A283839


c.

Remove the 3 bolts and 4 nuts and disconnect the engine wire from the engine assembly.


Hide 11201 19.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 20.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A287578C03
1.01,1.115 1.906,0.583 1.906,0.583 3.063,1.156 false 1.01,1.375 1.948,2.479 1.948,2.479 3.01,1.406 false 1.604,1.5 1.948,1.958 1.948,1.958 1.948,2.031 false 3.104,1.792 3.104,2.24 false 1.625,3.198 2.219,2.688 2.219,2.688 2.313,2.688 false 1.802,0.396 2,0.563 0.198,0.167 10 true *a 1.854,2.51 2.052,2.677 0.198,0.167 10 false *b 1.885,2.031 2.083,2.198 0.198,0.167 10 false A 3.042,2.25 3.24,2.417 0.198,0.167 10 false A 2.323,2.604 2.521,2.771 0.198,0.167 10 false *c
*a Paint Mark
*b Timing Mark
*c Timing Notch (Groove)


Turn the crankshaft pulley until its timing notch (groove) and the timing mark "0" of the timing chain cover sub-assembly are aligned.


b.

Check that both timing marks on the camshaft timing gear assembly and camshaft timing exhaust gear assembly are facing upward as shown in the illustration. If not, turn the crankshaft 1 revolution (360°) to align the timing marks as shown in the illustration.

HINT:

"A" is not a timing mark.



c.

Place paint marks on the chain sub-assembly in alignment with the timing marks on the camshaft timing gear assembly and camshaft timing exhaust gear assembly.


Hide 11324 21.REMOVE TIMING CHAIN COVER PLATE

a.
A250986

Remove the 4 bolts, timing chain cover plate and gasket.


Hide 13540 22.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A245327N15
1.958,0.198 2.229,0.375 0.271,0.177 10 10°

Turn the crankshaft pulley approximately 10° clockwise.


b.
A249931N10
2.031,0.229 2.281,0.375 0.25,0.146 10 10°

Turn the crankshaft pulley approximately 10° counterclockwise.


c.
A249932C14
1.854,1.969 1.635,1.708 false 1.698,1.01 1.302,0.5 1.302,0.5 1.125,0.5 false 1.896,1.948 2.125,2.094 0.229,0.146 10 false *a 0.938,0.427 1.167,0.573 0.229,0.146 10 true *b
*a Pin
*b Stopper Plate


Align the holes of the stopper plate and No. 1 chain tensioner assembly, and insert a pin into the stopper plate hole to lock the No. 1 chain tensioner assembly.


d.
A245327N15
1.958,0.198 2.229,0.375 0.271,0.177 10 10°

Turn the crankshaft pulley approximately 10° clockwise.


e.
A249933

Remove the 2 bolts, No. 1 chain tensioner assembly and gasket.

NOTICE:

Make sure not to drop the gasket inside the timing chain cover sub-assembly.



f.
A249931N10
2.031,0.229 2.281,0.375 0.25,0.146 10 10°

Turn the crankshaft pulley approximately 10° counterclockwise.


Hide 24.REMOVE TIMING CHAIN COVER TIGHT PLUG

Hide 13050 25.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.
A249934C01
2.208,0.094 2.521,0.292 0.313,0.198 10 true *a 0.208,0.688 0.521,0.885 0.313,0.198 10 false *b
*a Hold
*b Turn


Using a wrench to hold the hexagonal portion of the camshaft, remove the bolt from the camshaft.

NOTICE:

Be careful not to damage the cylinder head sub-assembly or spark plug tube with the wrench.



b.
A249936

Separate the camshaft timing gear assembly from the camshaft.


c.
A249937C09
1.179,2.967 1.385,3.134 0.206,0.167 10 *a 2.693,2.023 2.899,2.19 0.206,0.167 10 *a 1.224,2.023 1.431,2.19 0.206,0.167 10 *b 2.758,2.967 2.964,3.134 0.206,0.167 10 *b
*a Narrow
*b Wide


Separate the chain sub-assembly from the camshaft timing gear assembly, and turn the camshaft timing gear assembly approximately 180°.


d.
A249938

Remove the camshaft timing gear assembly.

NOTICE:

Do not disassemble the camshaft timing gear assembly.



Hide 26.REMOVE CAMSHAFT BEARING CAP

a.
A250989N03
0.573,1.865 0.688,2.031 0.115,0.167 10 true 1 0.677,0.042 0.792,0.208 0.115,0.167 10 false 2 0.229,1.073 0.344,1.24 0.115,0.167 10 true 3 2.896,0.073 3.01,0.24 0.115,0.167 10 false 4 2.979,1.573 3.094,1.74 0.115,0.167 10 true 5 1.219,0.073 1.333,0.24 0.115,0.167 10 false 6 1.188,1.573 1.302,1.74 0.115,0.167 10 true 7 2.344,0.073 2.458,0.24 0.115,0.167 10 false 8 2.396,1.573 2.51,1.74 0.115,0.167 10 true 9 1.719,0.073 1.906,0.24 0.188,0.167 10 true 10 1.76,1.573 1.948,1.74 0.188,0.167 10 true 11

Remove the 11 bolts in several steps in the order shown in the illustration.


b.
A250988N03
0.656,0.344 0.771,0.51 0.115,0.167 10 true 2 3.01,1.813 3.125,1.979 0.115,0.167 10 false 3 2.958,0.396 3.073,0.563 0.115,0.167 10 true 4 1.177,1.813 1.292,1.979 0.115,0.167 10 true 5 1.219,0.396 1.333,0.563 0.115,0.167 10 true 6 2.406,1.813 2.521,1.979 0.115,0.167 10 true 7 2.375,0.396 2.49,0.563 0.115,0.167 10 true 8 1.802,1.813 1.917,1.979 0.115,0.167 10 true 9 1.75,0.396 1.938,0.563 0.188,0.167 10 true 10 0.563,1.979 0.677,2.146 0.115,0.167 10 false 1

Remove the 10 bolts in several steps in the order shown in the illustration.


c.

Remove the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap and 3 No. 3 camshaft bearing caps.

HINT:

Arrange the removed parts in the correct order.



Hide 13511 27.REMOVE CAMSHAFT

a.
A249939

Remove the camshaft from the camshaft housing sub-assembly.


Hide 13512 28.REMOVE NO. 2 CAMSHAFT

a.
A249940

Hold up the chain sub-assembly and remove the No. 2 camshaft from the camshaft housing sub-assembly.


b.
A249941

Suspend the chain sub-assembly with a string or equivalent as shown in the illustration.

NOTICE:

Be careful not to drop the chain sub-assembly inside the timing chain cover sub-assembly.



Hide 13070A 29.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.

Secure the No. 2 camshaft in a vise by clamping the hexagonal part between aluminum plates.

NOTICE:

Do not damage the No. 2 camshaft by tightening the vise excessively.



b.
A250991

Remove the bolt and camshaft timing exhaust gear assembly.

NOTICE:

Do not disassemble the camshaft timing exhaust gear assembly.



Hide 15678A 30.REMOVE OIL CONTROL VALVE FILTER

Hide 11811 31.REMOVE NO. 1 CAMSHAFT BEARING

Hide 11821 32.REMOVE NO. 2 CAMSHAFT BEARING