Home › Vehicle Interior › HEATING / AIR CONDITIONING › CONDENSER › 2020.02–2020.11
RM37A0E _58 Vehicle Interior _086896 HEATING / AIR CONDITIONING _0417372 CONDENSER A

HEATING / AIR CONDITIONING  CONDENSER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during cooler condenser assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

Front bumper assembly*
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Front television camera view adjustment Panoramic View Monitor System (Click here)

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

Front bumper assembly*
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Front television camera view adjustment Panoramic View Monitor System (Click here)

PROCEDURE

Hide 1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 2.REMOVE FRONT BUMPER ASSEMBLY

Hide 52611 3.REMOVE FRONT BUMPER ENERGY ABSORBER

Hide 52021 4.REMOVE FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY

Hide 17750A 6.REMOVE INLET AIR CLEANER ASSEMBLY (for 2GR-FKS)

Hide 17750A 7.REMOVE INLET AIR CLEANER ASSEMBLY (for A25A-FXS)

Hide 53205 8.REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY (for 2GR-FKS)

Hide 53205 9.REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY (for A25A-FXS)

Hide 16595B 11.REMOVE NO. 1 RADIATOR AIR GUIDE LH

a.
E431993C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the clip.


b.

Disengage the claw and 2 guides, and remove the No. 1 radiator air guide LH as shown in the illustration.


Hide 16593B 12.REMOVE NO. 1 RADIATOR AIR GUIDE RH

a.
E431995C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the clip.


b.

Disengage the claw and guide, and remove the No. 1 radiator air guide RH as shown in the illustration.


Hide G9010A 13.DISCONNECT RADIATOR ASSEMBLY (for HV Model)

a.

for Inverter Coolant:

i.
E406578

Remove the 4 bolts.


ii.

Disengage the 2 claws and disconnect the radiator assembly.


iii.
E431998C01
0,0 0,0 false
V113147

Separate in this Direction


Separate the radiator assembly as shown in the illustration.

NOTICE:

Do not apply excessive force to the No. 3 inverter cooling hose and No. 4 inverter cooling hose.




Hide 88703 14.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY (for Gasoline Model)

a.
E432000

Remove the bolt.


b.

Disconnect the discharge hose sub-assembly.


c.

Remove the O-ring from the discharge hose sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 88703 15.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY (for HV Model)

a.
E432001

Remove the bolt.


b.

Disconnect the discharge hose sub-assembly.


c.

Remove the O-ring from the discharge hose sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 88710 16.DISCONNECT AIR CONDITIONING TUBE ASSEMBLY (for Gasoline Model)

a.

While pressing the end of the air conditioning tube assembly into the end of the cooler condenser assembly, use pliers to squeeze together both sides of the piping clamp until it breaks apart.

E432002C01
3.313,1.521 2.917,2 2.917,2 3.25,1.792 true 5,2.75 5,2.271 false 6.333,2.75 6.333,2.438 false 4.948,2.771 5.26,2.927 0.313,0.156 10 false *1 6.26,2.771 6.573,2.927 0.313,0.156 10 false *2 2.854,2.021 3.167,2.177 0.313,0.156 10 false *3 4.865,1.125 5.177,1.281 0.313,0.156 10 false *a
*1 Air Conditioning Tube Assembly *2 Cooler Condenser Assembly
*3 Piping Clamp - -
*a Press In - -


NOTICE:
·

If any foreign matter is attached to the connecting parts, brush it off or use compressed air to remove it before disconnecting the parts.

·

Make sure that fragments of the piping clamp do not enter the piping.




b.

Disconnect the air conditioning tube assembly.

NOTICE:

Remove any foreign matter from the connecting parts of the air conditioning tube assembly and cooler condenser assembly.



c.

Remove the 2 O-rings from the air conditioning tube assembly.

NOTICE:

Seal the openings of the disconnected parts with vinyl tape to prevent entry of moisture and foreign matter.



d.

Remove the piping clamp.


Hide 88710 17.DISCONNECT AIR CONDITIONING TUBE ASSEMBLY (for HV Model)

a.

While pressing the end of the air conditioning tube assembly into the end of the cooler condenser assembly, use pliers to squeeze together both sides of the piping clamp until it breaks apart.

E434830C01
3.24,1.417 2.917,2 2.917,2 3.271,1.823 true 4.813,2.375 4.813,1.896 false 6.24,2.375 6.24,2.063 false 4.75,2.396 5.063,2.552 0.313,0.156 10 false *1 6.188,2.406 6.5,2.563 0.313,0.156 10 false *2 2.781,2.021 3.094,2.177 0.313,0.156 10 false *3 4.729,0.74 5.042,0.896 0.313,0.156 10 false *a
*1 Air Conditioning Tube Assembly *2 Cooler Condenser Assembly
*3 Piping Clamp - -
*a Press In - -


NOTICE:
·

If any foreign matter is attached to the connecting parts, brush it off or use compressed air to remove it before disconnecting the parts.

·

Make sure that fragments of the piping clamp do not enter the piping.




b.

Disconnect the air conditioning tube assembly.

NOTICE:

Remove any foreign matter from the connecting parts of the air conditioning tube assembly and cooler condenser assembly.



c.

Remove the 2 O-rings from the air conditioning tube assembly.

NOTICE:

Seal the openings of the disconnected parts with vinyl tape to prevent entry of moisture and foreign matter.



d.

Remove the piping clamp.


Hide 88460 18.REMOVE COOLER CONDENSER ASSEMBLY (for Gasoline Model)

a.
E432006C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and 2 guides, and remove the cooler condenser assembly as shown in the illustration.

NOTICE:

Do not damage the cooler condenser assembly or radiator assembly when removing the cooler condenser assembly.



Hide 88460 19.REMOVE COOLER CONDENSER ASSEMBLY (for HV Model)

a.
E432004C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 guides to remove the cooler condenser assembly as shown in the illustration.

NOTICE:

Do not damage the cooler condenser assembly or radiator assembly when removing the cooler condenser assembly.