The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during port fuel injector assembly removal/installation are shown below.
Never perform work on fuel system components near any possible ignition sources.
Vaporized fuel could ignite, resulting in a serious accident.
Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.
Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.
After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
2. DISCHARGE FUEL SYSTEM PRESSURE
58441L
3.REMOVE BATTERY SERVICE HOLE COVER
4.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
22030
5.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY
25620
6.REMOVE EGR VALVE ASSEMBLY
16278
7.REMOVE NO. 2 WATER BY-PASS PIPE
23910A
8.DISCONNECT FUEL TUBE SUB-ASSEMBLY
Remove the fuel pipe clamp from the fuel tube connector.
Disconnect the fuel tube sub-assembly from the fuel pump assembly and fuel delivery pipe sub-assembly.
Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (FUEL)>FUEL SYSTEM>PRECAUTION
23801P
9.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY
To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.
Disconnect the ignition coil connector.
for EGR Valve Bracket Connection Type:
Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.
for Cylinder Head Cover Sub-assembly Connection Type:
|
Union Nut |
|
Bolt |
Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.
Using an 8 mm socket wrench, remove the bolt.
Loosen the 2 bolts of the fuel pump assembly.
Remove the No. 1 fuel pipe sub-assembly from the fuel delivery pipe and fuel pump assembly.
23100X
10.REMOVE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY
23807
11.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY
Disconnect the No. 5 engine wire connector.
Remove the 2 bolts and fuel delivery pipe sub-assembly with the 4 port fuel injector assemblies from the cylinder head sub-assembly.
Be careful not to drop the port fuel injector assemblies when removing the fuel delivery pipe sub-assembly.
23807V
12.REMOVE NO. 1 DELIVERY PIPE SPACER
Remove the 2 No. 1 delivery pipe spacers from the cylinder head sub-assembly.
23291
13.REMOVE INJECTOR VIBRATION INSULATOR
Remove the 4 injector vibration insulators from the cylinder head sub-assembly.
82125N
14.REMOVE NO. 5 ENGINE WIRE
Disconnect the 4 port fuel injector assembly connectors and No. 2 fuel pressure sensor connector.
Disengage the 2 clamps to remove the No. 5 engine wire from the fuel delivery pipe sub-assembly.
23250F
15.REMOVE PORT FUEL INJECTOR ASSEMBLY
Pull the 4 port fuel injector assemblies out of the fuel delivery pipe sub-assembly.
Remove the O-ring from each port fuel injector assembly.
Attach a tag or label with the corresponding cylinder number to each port fuel injector assembly so that they can be installed to their original locations.
Cover the port fuel injector assemblies with plastic bags to prevent damage and contamination.