Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR
RM37A0E _59 Vehicle Exterior _086885 DOOR / HATCH _0418599 REAR DOOR A

DOOR / HATCH  REAR DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


Hide 67837C 2.INSTALL REAR DOOR DUST PROOF SEAL

a.
B564479

Engage the 3 claws to install 3 new rear door dust proof seals.


Hide 67846A 3.INSTALL REAR DOOR FRONT OUTSIDE SEAL

a.
B564478

Engage the guide and 4 claws to install the rear door front outside seal.


Hide 67888A 4.INSTALL REAR DOOR NO. 2 WEATHERSTRIP

a.
B564477

Engage the 6 clips to install the rear door No. 2 weatherstrip.


Hide 75797G 5.INSTALL REAR DOOR UPPER OUTSIDE MOULDING PAD

Hide 6.INSTALL REAR DOOR OUTSIDE MOULDING SUB-ASSEMBLY

Hide 75078 7.INSTALL REAR DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY

Hide 67003C 8.INSTALL REAR DOOR PANEL CUSHION

a.
B564476

Engage the claw to install a new rear door panel cushion.


Hide 67896 9.INSTALL REAR DOOR NO. 3 WEATHERSTRIP

a.

Clean the rear door panel.


b.

Remove the release paper from a new rear door No. 3 weatherstrip.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



c.

Install the rear door No. 3 weatherstrip.

B564475C01
0,0 0,0 false
V100155

Double-sided Tape - -



Hide 75792 10.INSTALL DOOR WINDOW FRAME MOULDING CLIP

a.
B564474

Engage the 2 claws to install the door window frame moulding clip.


Hide 75764A 11.INSTALL REAR DOOR UPPER WINDOW FRAME MOULDING

Hide 75766B 12.INSTALL REAR DOOR REAR WINDOW FRAME MOULDING

Hide 75762B 13.INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING

Hide 75740 14.INSTALL REAR DOOR BELT MOULDING ASSEMBLY

Hide 67836H 15.INSTALL REAR DOOR LOCK CHILD PROTECTION COVER

a.
B564472

Engage the 6 claws to install the rear door child protection cover.


Hide 69204A 16.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

Apply MP grease to the sliding parts of the rear door outside handle frame sub-assembly.


b.
B567549C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide and claw as shown in the illustration.


c.
B564470

Using a T30 "TORX" socket wrench, install the rear door outside handle frame sub-assembly with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69242G 17.INSTALL REAR DOOR REAR OUTSIDE HANDLE PAD

a.
B564469

Engage the 3 guides and claw to install the rear door rear outside handle pad.


Hide 69241G 18.INSTALL REAR DOOR FRONT OUTSIDE HANDLE PAD

a.
B564468

Engage the guide and 2 claws to install the rear door front outside handle pad.


Hide 69227M 19.INSTALL REAR DOOR OUTSIDE HANDLE COVER

a.
B564467

Engage the 2 claws.


b.

Using a T30 "TORX" socket wrench, install the rear door outside handle cover with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69240 20.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY

a.
B564466C01
0,0 0,0 false
V113147

Install in this Direction


Insert the front end of the rear door outside handle assembly into the rear door outside handle frame sub-assembly as shown in the illustration.


b.

Insert the rear end of the rear door outside handle assembly into the rear door outside handle frame sub-assembly, then slide the rear door outside handle assembly toward the front of the vehicle to install it.


c.
B564464

Move the lever as shown in the illustration and engage the 2 claws to lock the rear door outside handle assembly.


Hide 69060A 21.INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY

Hide 22.INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY

a.

Apply MP grease to the sliding parts of the rear door window regulator assembly.


b.
B564462

Install the rear door window regulator assembly with the 6 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


c.

Connect the connector.


Hide 68104 23.INSTALL REAR DOOR GLASS SUB-ASSEMBLY

a.

Connect the rear power window regulator switch assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON.


d.

Move the rear door window regulator assembly so that the door glass bolt holes can be seen.


e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.


g.

Disconnect the rear power window regulator switch assembly.


h.
B564460C01
0,0 0,0 false
V113147

Install in this Direction


Insert the rear door glass sub-assembly into the rear door panel as shown in the illustration.

NOTICE:

Do not damage the rear door glass sub-assembly.



i.
B564458

Install the rear door glass sub-assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


j.
B564457

Install the hole plug.


Hide 68189 24.INSTALL REAR DOOR QUARTER WINDOW WEATHERSTRIP

a.
B564456

Install the rear door quarter window weatherstrip from the rear door quarter window glass.


Hide 68124B 25.INSTALL REAR DOOR QUARTER WINDOW GLASS

a.
B564455C01
0,0 0,0 false
V113147

Install in this Direction


Install the rear door quarter window glass as shown in the illustration.


Hide 67408E 26.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

a.
B564453C01
0,0 0,0 false
V100135

Screw
V100136

Bolt


Install the rear door window division bar sub-assembly with the 2 bolts and screw.

Torque:
Bolt : 8.5 N*m (87 kgf*cm, 75 in.*lbf)
Screw : 3.1 N*m (32 kgf*cm, 27 in.*lbf)


Hide 68152C 27.INSTALL REAR DOOR GLASS RUN

a.
B567548

Install the rear door glass run.


Hide 67842E 28.INSTALL REAR DOOR SERVICE HOLE COVER

a.
B564452

Engage the 7 clips to install the rear door service hole cover.


b.
B564451

Engage the 2 clamps.


c.

Connect the connector.


Hide 67225A 29.INSTALL QUARTER WINDOW UPPER STOP

a.
B564450C01
0,0 0,0 false
V113147

Install in this Direction


Install the quarter window upper stop as shown in the illustration.


Hide 67848A 30.INSTALL NO. 1 REAR DOOR VENT SEAL

a.
B564448C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 3 guides to install the No. 1 rear door front vent seal as shown in the illustration.


Hide 68174A 31.INSTALL REAR DOOR INNER GLASS WEATHERSTRIP

a.
B564446C01
0,0 0,0 false
V113147

Install in this Direction


Install the rear door inner glass weatherstrip as shown in the illustration.


Hide 67872 32.INSTALL REAR DOOR WEATHERSTRIP

a.

Clean the rear door panel.

i.

Remove any remaining double-sided tape from the rear door panel.


ii.

Wipe off any tape adhesive residue with cleaner.



b.

Remove the release paper from a new rear door weatherstrip.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



c.
B564444C01
0,0 0,0 false
V100155

Double-sided Tape


Engage the guide and 28 clips to install the rear door weatherstrip.


Hide 68640A 33.INSTALL REAR DOOR CHECK ASSEMBLY

a.

Clean the bolt hole in the vehicle body.


b.

Clean the threads of the bolt.


c.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.
B564442C01
0,0 0,0 false
V100135

Nut
V100136

Bolt


Install the rear door check assembly with the 2 nuts and bolt.

Torque:
Bolt : 27 N*m (275 kgf*cm, 20 ft.*lbf)
Nut : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 86160B 34.INSTALL REAR SPEAKER ASSEMBLY

Hide 67676C 35.INSTALL NO. 2 REAR DOOR FRAME GARNISH

a.
B564441

Engage the 3 claws to install the No. 2 rear door frame garnish.


b.
B572356

Using a moulding remove or equivalent, pull out the rear door quarter window weatherstrip from under the No. 2 rear door frame garnish.


Hide 67674A 36.INSTALL REAR DOOR FRAME GARNISH

a.
B564440C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 guides as shown in the illustration.


b.

Engage the clip to install the rear door frame garnish.


Hide 65923E 37.INSTALL CURTAIN HOOK (w/ Rear Door Sunshade)

HINT:

Use the same procedure for both curtain hooks.


a.
B567552C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws to install the curtain hook as shown in the illustration.


b.
B564481

Engage the pin as shown in the illustration.


Hide 65908D 38.INSTALL REAR CURTAIN SUB-ASSEMBLY (w/ Rear Door Sunshade)

a.
B564438

Engage the 3 guides.


b.

Install the rear curtain sub-assembly with the 7 screws.


Hide 74222C 39.INSTALL REAR DOOR ARMREST COVER

a.
B564437C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claw to install the rear door armrest cover as shown in the illustration.


Hide 69206C 40.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B564435

Engage the 3 claws to install the rear door inside handle sub-assembly.


Hide 67604 41.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

a.
B564434C01
1.958,0.958 2.563,0.604 true 2.083,1.677 1.896,1.302 true 2.573,0.49 2.792,0.667 0.219,0.177 10 true *1 2,1.688 2.219,1.875 0.219,0.188 10 true *2
*1 Rear Door Inside Lock/Unlock Knob Locking Cable
*2 Rear Door Lock Open Lever Remote Control Cable
V113147

Install in this Direction


Connect the rear door lock open lever remote control cable and rear door inside lock/unlock knob locking cable to the rear door inside handle sub-assembly as shown in the illustration.


b.

w/ Illumination:

i.
B564432

Connect the connector.


ii.

Engage the clamp.



c.
B564431C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide, 4 claws and 9 clips as shown in the illustration.


d.
B564428

Install the rear door trim board sub-assembly with the 3 screws.


e.
B564427

Engage the claw as shown in the illustration.


Hide 69278C 42.INSTALL REAR DOOR INSIDE HANDLE BEZEL

a.
B564425

Engage the 3 claws to install the rear door inside handle bezel.


Hide 43.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

a.

Connect the connector.


b.
B564423

Engage the 5 guides, 2 claws and 2 clips to install the rear power window regulator switch assembly with rear door upper armrest base panel.


Hide 44.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 58441L 45.INSTALL BATTERY SERVICE HOLE COVER (for HV Model)

Hide 46.INITIALIZE POWER WINDOW CONTROL SYSTEM