Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › SFI SYSTEM
RM37A0E _51 Engine / Hybrid System _086849 2GR-FKS ENGINE CONTROL _0418696 SFI SYSTEM J

2GR-FKS ENGINE CONTROL  SFI SYSTEM  Active Control Engine Mount System  


DESCRIPTION

LOCATION
A454575C01
2.615,3.958 2.76,3.958 2.76,3.958 3.021,3.656 true 3.667,4.177 3.5,4.177 3.5,4.177 3.26,3.583 true 2.438,3.875 2.75,4.073 0.313,0.198 10 false *2 3.729,4.094 4.042,4.292 0.313,0.198 10 false *1
*1 Vacuum Switching Valve (for Active Control Engine Mount) *2 Front Engine Mounting Insulator Assembly



The active control engine mount system decreases engine vibration at a low engine speed using the vacuum switching valve (for active control engine mount). The vacuum switching valve (for active control engine mount) is controlled by a pulse signal transmitted to the vacuum switching valve (for active control engine mount) from the ECM. The frequency of this pulse signal is matched to the engine speed to decrease engine vibration.

WIRING DIAGRAM

A410586E09
0.604,3.781 1.677,3.979 1.073,0.198 10 false Battery 0.531,3.083 1.177,3.313 0.646,0.229 10 false FL MAIN 0.49,2.156 1.177,2.385 0.688,0.229 10 false EFI-MAIN 1.708,1.979 2.427,2.24 0.719,0.26 10 false EFI-MAIN 2.646,1.354 3.375,1.604 0.729,0.25 10 false EFI NO. 4 3.615,1.094 3.771,1.292 0.156,0.198 10 false 1 4.906,1.094 5.063,1.292 0.156,0.198 10 false 2 3.667,1.521 4.125,1.719 0.458,0.198 10 false C12 3.667,1.698 5.458,2.333 1.792,0.635 10 false Vacuum Switching Valve (for Active Control Engine Mount) 5.323,1.188 5.708,1.406 0.385,0.219 10 false C54 5.375,1 5.688,1.198 0.313,0.198 10 false 39 5.635,1.083 6.094,1.281 0.458,0.198 10 false ACM 5.313,2.927 5.771,3.125 0.458,0.198 10 false A28 5.365,2.76 5.677,2.958 0.313,0.198 10 false 46 5.646,2.823 6.26,3.021 0.615,0.198 10 false MREL 6.042,3.906 6.5,4.104 0.458,0.198 10 false ECM 1.594,1.594 1.75,1.792 0.156,0.198 10 false 1 2.26,1.594 2.417,1.792 0.156,0.198 10 false 2 2.25,1.094 2.406,1.292 0.156,0.198 10 false 5 1.594,1.094 1.75,1.292 0.156,0.198 10 false 3 3.781,1.094 4.094,1.292 0.313,0.198 10 false +B 4.51,1.094 4.969,1.292 0.458,0.198 10 false ACM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK VACUUM HOSES
a.
A337271C03
1.448,2.865 1.313,2.865 1.313,2.865 1.271,2.5 true 0.625,1.604 0.938,1.802 0.313,0.198 10 false *1 1.292,1.385 1.552,1.615 0.26,0.229 10 false *2 2.573,1.333 2.802,1.552 0.229,0.219 10 false *5 2.583,0.479 2.896,0.677 0.313,0.198 10 false *4 1.49,2.792 1.802,2.99 0.313,0.198 10 false *3
*1 Engine
*2 Intake Air Surge Tank Assembly
*3 Front Engine Mounting Insulator
*4 ECM
*5 Vacuum Switching Valve (for Active Control Engine Mount)


Check the air and vacuum hoses for looseness, disconnection and blockage.

OK:

No looseness, disconnection or blockage.



Result:
Proceed to
OK
NG



OK

2.CHECK VACUUM

NG

REPAIR OR REPLACE VACUUM HOSES

2.CHECK VACUUM
a.
A454576

Disconnect the vacuum hose from the intake air surge tank assembly.


b.

Start the engine.


c.

Check that the disconnected port located on the intake air surge tank assembly applies suction to your finger.

OK:

Vacuum exists.



Result:
Proceed to
OK
NG



OK

3.INSPECT VACUUM SWITCHING VALVE (FOR ACTIVE CONTROL ENGINE MOUNT) (OPERATION)

NG

CHECK AND REPLACE VACUUM SOURCE AND HOSES

3.INSPECT VACUUM SWITCHING VALVE (FOR ACTIVE CONTROL ENGINE MOUNT) (OPERATION)

OK

4.INSPECT VACUUM SWITCHING VALVE (FOR ACTIVE CONTROL ENGINE MOUNT) (RESISTANCE)

NG

REPLACE VACUUM SWITCHING VALVE (FOR ACTIVE CONTROL ENGINE MOUNT)

4.INSPECT VACUUM SWITCHING VALVE (FOR ACTIVE CONTROL ENGINE MOUNT) (RESISTANCE)

OK

5.INSPECT FRONT ENGINE MOUNTING INSULATOR

NG

REPLACE VACUUM SWITCHING VALVE (FOR ACTIVE CONTROL ENGINE MOUNT)

5.INSPECT FRONT ENGINE MOUNTING INSULATOR

OK

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VACUUM SWITCHING VALVE (FOR ACTIVE CONTROL ENGINE MOUNT))

NG

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VACUUM SWITCHING VALVE (FOR ACTIVE CONTROL ENGINE MOUNT))
A337501C42
0.552,1.188 0.896,1.438 0.344,0.25 1.104,1.802 1.521,1.385 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 0.604,1.24 0.917,1.438 0.313,0.198 10 false C12 0.969,1.823 1.281,2.021 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Vacuum Switching Valve (for Active Control Engine Mount))


a.

Disconnect the vacuum switching valve (for active control engine mount) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C12-1(+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR ACTIVE CONTROL ENGINE MOUNT) - ECM)

NG

7.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR ACTIVE CONTROL ENGINE MOUNT) - ECM)
a.

Disconnect the vacuum switching valve (for active control engine mount) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C12-2(ACM) - C54-39 (ACM) Always Below 1 Ω
C12-2(ACM) or C54-39 (ACM) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR