The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed or replaced during engine unit removal/installation are shown below.
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
43457
1.REMOVE DRIVE SHAFT BEARING BRACKET
Remove the 3 bolts and drive shaft bearing bracket.
88370
2.REMOVE COMPRESSOR WITH MOTOR ASSEMBLY
|
Bolt |
|
Nut |
Remove the bolt and 2 nuts.
Using an E8 "TORX" socket wrench, remove the 2 stud bolts and compressor with motor assembly.
16207
3.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
Slide the clip and disconnect the No. 2 water by-pass pipe sub-assembly from the water by-pass outlet.
Remove the bolt and the No. 2 water by-pass pipe sub-assembly.
16260
4.REMOVE FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)
Remove the bolt.
Slide the clip and remove the flow shutting valve (water by-pass hose assembly) from the water by-pass outlet.
Remove the 2 bolts and water hose clamp bracket.
17167
5.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
Remove the 5 bolts and the No. 1 exhaust manifold heat insulator from the exhaust manifold (TWC: Front Catalyst).
17118
6.REMOVE MANIFOLD STAY
17141
7.REMOVE EXHAUST MANIFOLD (TWC: Front Catalyst)
Using a 12 mm deep socket wrench, remove the 7 nuts and remove the exhaust manifold (TWC: Front Catalyst) from the cylinder head sub-assembly.
Remove the exhaust manifold to head gasket from the cylinder head sub-assembly.
22030
8.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY
22271
9.REMOVE THROTTLE BODY GASKET
25680
10.REMOVE EGR COOLER ASSEMBLY
| *1 | No. 3 Water By-pass Hose |
| *2 | No. 4 Water By-pass Hose |
Slide the clip and disconnect the No. 4 water by-pass hose from the EGR cooler assembly.
Slide the clip and disconnect the No. 3 water by-pass hose from the EGR cooler assembly.
Remove the 5 bolts, EGR cooler assembly, EGR cooler gasket and EGR valve gasket.
25601
11.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY
16281
12.REMOVE NO. 4 WATER BY-PASS HOSE
Slide the clip and remove the No. 4 water by-pass hose from the EGR valve assembly.
25620
13.REMOVE EGR VALVE ASSEMBLY
Slide the clip and disconnect the No. 8 water by-pass hose from the EGR valve assembly.
for EGR Valve Bracket Connection Type:
Using an 8 mm socket wrench, remove the bolt and disconnect the No. 1 fuel pipe sub-assembly from the EGR valve bracket.
Using an 8 mm socket wrench, remove the bolt.
| *a | Pin |
| *b | Hole |
Remove the EGR valve assembly vertically.
for Cylinder Head Cover Sub-assembly Connection Type:
Using an 8 mm socket wrench, remove the bolt.
| *a | Pin |
| *b | Hole |
Remove the EGR valve assembly vertically.
Using an 8 mm socket wrench, remove the bolt and EGR valve bracket.
16279
14.REMOVE NO. 3 WATER BY-PASS PIPE
Using an 8 mm socket wrench, remove the bolt and disconnect the No. 3 water by-pass pipe from the intake manifold.
Slide the clip and remove the No. 3 water by-pass pipe from the water outlet.
16278
15.REMOVE NO. 2 WATER BY-PASS PIPE
Remove the bolt (A).
Using an 8 mm socket wrench, remove the 2 bolts (B) and No. 2 water by-pass pipe.
17111
16.REMOVE INTAKE MANIFOLD
17177
17.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET
23910A
18.DISCONNECT FUEL TUBE SUB-ASSEMBLY
23801P
19.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY
for EGR Valve Bracket Connection Type:
Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.
for Cylinder Head Cover Sub-assembly Connection Type:
Using an 8 mm socket wrench, remove the bolt.
Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.
23100X
20.REMOVE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)
16295
21.REMOVE NO. 7 WATER BY-PASS HOSE
Slide the 2 clips and remove the No. 7 water by-pass hose.
82219A
22.REMOVE SENSOR WIRE
Disconnect the 4 connectors.
Disengage the 3 clamps.
Using an 8 mm socket wrench, remove the bolt and sensor wire from the water inlet with thermostat sub-assembly.
82126A
23.REMOVE NO. 6 ENGINE WIRE
Disconnect the 4 connectors.
Disengage the 2 clamps.
Remove the 2 nuts and No. 6 engine wire from the wire harness clamp bracket.
24.REMOVE WIRE HARNESS CLAMP BRACKET
Using an 8 mm socket wrench, remove the 2 bolts and wire harness clamp bracket from the No. 1 ventilation case.
23807
25.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY
23807V
26.REMOVE NO. 1 DELIVERY PIPE SPACER
23291
27.REMOVE INJECTOR VIBRATION INSULATOR
82125N
28.REMOVE NO. 5 ENGINE WIRE
23250F
29.REMOVE PORT FUEL INJECTOR ASSEMBLY
23814B
30.REMOVE FUEL DELIVERY PIPE
23250E
31.REMOVE DIRECT FUEL INJECTOR ASSEMBLY
19500
32.REMOVE IGNITION COIL ASSEMBLY
11452
33.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
Remove the engine oil level dipstick.
Using an 8 mm socket wrench, remove the bolt and engine oil level dipstick guide from the camshaft housing sub-assembly.
Remove the O-ring from the engine oil level dipstick guide.
17169A
34.REMOVE NO. 3 EXHAUST MANIFOLD HEAT INSULATOR
Remove the bolt and No. 3 exhaust manifold heat insulator from the cylinder block sub-assembly.