Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2020.02–2020.11
RM37A0E _55 Steering _086874 POWER ASSIST SYSTEMS _0419667 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1567  Error in Matching of ECUs  


DESCRIPTION

for Gasoline Model:

The power steering ECU (rack and pinion power steering gear assembly) determines whether an incompatible ECM, main body ECU (multiplex network body ECU) or skid control ECU (brake actuator assembly) is installed based on the identification information.


for HV Model:

The power steering ECU (rack and pinion power steering gear assembly) determines whether an incompatible hybrid vehicle control ECU, main body ECU (multiplex network body ECU) or No. 2 skid control ECU (brake actuator assembly) is installed based on the identification information.


DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition Note
C1567 Error in Matching of ECUs
for Gasoline Model:
·

An incompatible ECM is detected

·

An incompatible main body ECU (multiplex network body ECU) is detected

·

An incompatible skid control ECU (brake actuator assembly) is detected


for HV Model:
·

An incompatible hybrid vehicle control ECU is detected

·

An incompatible main body ECU (multiplex network body ECU) is detected

·

An incompatible No. 2 skid control ECU (brake actuator assembly) is detected


for Gasoline Model:
·

Incorrect ECM

·

Incorrect main body ECU (multiplex network body ECU)

·

Incorrect skid control ECU (brake actuator assembly)

·

Rack and pinion power steering gear assembly


for HV Model:
·

Incorrect hybrid vehicle control ECU

·

Incorrect main body ECU (multiplex network body ECU)

·

Incorrect No. 2 skid control ECU (brake actuator assembly)

·

Rack and pinion power steering gear assembly


EPS warning light: Comes on Ignition switch is turned to ON again -

CAUTION / NOTICE / HINT

NOTICE:

If the rack and pinion power steering gear assembly has been replaced, perform assist map writing and torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION


PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for Gasoline Model A
for HV Model B



A

2.CHECK RELATED PART

B

6.CHECK RELATED PART
2.CHECK RELATED PART
a.

Confirm if the related part has the correct part number.

Related Part ECM
Main body ECU (Multiplex network body ECU)
Skid control ECU (Brake actuator assembly)

NOTICE:

When removing the related part to check it, be sure to follow the appropriate procedures and precautions.




Result:
Result Proceed to
The related part has the correct part number. A
The related part has an incorrect part number. B



A

3.CHECK FOR DTC

B

4.REPLACE RELATED PART WITH PART THAT HAS CORRECT PART NUMBER
3.CHECK FOR DTC
a.

Select Health Check on the GTS screen and check if system DTCs of the related part are output.

HINT:

If system DTCs of the related part are stored, assist map writing to the power steering ECU (rack and pinion power steering gear assembly) may not be performed properly.



Result:
Result Proceed to
System DTCs of the related part are output. A
System DTCs of the related part are not output. B



A

REPAIR CIRCUIT INDICATED BY OUTPUT CODE

B

REPLACE RACK AND PINION POWER STEERING GEAR ASSEMBLY

4.REPLACE RELATED PART WITH PART THAT HAS CORRECT PART NUMBER
a.

Replace the related part with one that has the correct part number.



Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Check for DTCs.

Chassis > EMPS > Trouble Codes
50001 142

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

END

B

REPLACE RACK AND PINION POWER STEERING GEAR ASSEMBLY

6.CHECK RELATED PART
a.

Confirm if the related part has the correct part number.

Related Part Hybrid vehicle control ECU
Main body ECU (Multiplex network body ECU)
No. 2 skid control ECU (Brake actuator assembly)

NOTICE:

When removing the related part to check it, be sure to follow the appropriate procedures and precautions.

·

Main body ECU (Multiplex network body ECU)

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

·

No. 2 skid control ECU (Brake actuator assembly)

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model LHD)>REMOVAL




Result:
Result Proceed to
The related part has the correct part number. A
The related part has an incorrect part number. B



A

7.CHECK FOR DTC

B

8.REPLACE RELATED PART WITH PART THAT HAS CORRECT PART NUMBER
7.CHECK FOR DTC
a.

Select Health Check on the GTS screen and check if system DTCs of the related part are output.

HINT:

If system DTCs of the related part are stored, assist map writing to the power steering ECU (rack and pinion power steering gear assembly) may not be performed properly.



Result:
Result Proceed to
System DTCs of the related part are output. A
System DTCs of the related part are not output. B



A

REPAIR CIRCUIT INDICATED BY OUTPUT CODE

B

REPLACE RACK AND PINION POWER STEERING GEAR ASSEMBLY

8.REPLACE RELATED PART WITH PART THAT HAS CORRECT PART NUMBER
a.

Replace the related part with one that has the correct part number.

·

Main body ECU (Multiplex network body ECU)

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

·

No. 2 skid control ECU (Brake actuator assembly)

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model LHD)>REMOVAL



Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Check for DTCs.

Chassis > EMPS > Trouble Codes
50001 142

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

END

B

REPLACE RACK AND PINION POWER STEERING GEAR ASSEMBLY