This DTC will be stored if the power steering ECU (rack and pinion power steering gear assembly) determines that the assist map is not written in the ECU.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Return-to-normal Condition | Note |
|---|---|---|---|---|---|---|
| C1581 | Assist Map Number Un-Writing | Assist map not written in power steering ECU (rack and pinion power steering gear assembly) | for Gasoline Model:
·
CAN communication system ·
ECM ·
Main body ECU (Multiplex network body ECU) ·
Skid control ECU (Brake actuator assembly) ·
Rack and pinion power steering gear assembly for HV Model:
·
CAN communication system ·
Hybrid vehicle control ECU ·
Main body ECU (Multiplex network body ECU) ·
No. 2 skid control ECU (Brake actuator assembly) ·
Rack and pinion power steering gear assembly |
EPS warning light: Comes on | Assist Map Writing is performed | - |
If the rack and pinion power steering gear assembly has been replaced, perform assist map writing and torque sensor zero point calibration.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION
Related parts store information necessary for assist map writing.
Related Part:
ECM
Main body ECU (Multiplex network body ECU)
Skid control ECU (Brake actuator assembly)
Hybrid vehicle control ECU
Main body ECU (Multiplex network body ECU)
No. 2 skid control ECU (Brake actuator assembly)
Perform assist map writing.
| Tester Display |
|---|
| Signal Check |
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC C1581 is output. | A |
| DTC C1581 is not output. | B |
A
B
Check for DTCs.
for Gasoline Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING
for HV Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are not output. (for Gasoline Model) | A |
| CAN communication system DTCs are not output. (for HV Model) | B |
| CAN communication system DTCs are output. | C |
A
B
C
for Gasoline Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING
for HV Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING
Confirm if the related part has the correct part number.
| Related Part | ECM |
| Main body ECU (Multiplex network body ECU) | |
| Skid control ECU (Brake actuator assembly) |
When removing the related part to check it, be sure to follow the appropriate procedures and precautions.
Main body ECU (Multiplex network body ECU)
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Skid control ECU (Brake actuator assembly)
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model LHD)>REMOVAL
| Result | Proceed to |
|---|---|
| The related part has the correct part number. | A |
| The related part has an incorrect part number. | B |
A
B
Select Health Check on the GTS screen and check if system DTCs of the related part are output.
If system DTCs of the related part are stored, assist map writing to the power steering ECU (rack and pinion power steering gear assembly) may not be performed properly.
| Result | Proceed to |
|---|---|
| System DTCs of the related part are output. | A |
| System DTCs of the related part are not output. | B |
A
B
Replace the related part with one that has the correct part number.
Main body ECU (Multiplex network body ECU)
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Skid control ECU (Brake actuator assembly)
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model LHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
A
B
Confirm if the related part has the correct part number.
| Related Part | Hybrid vehicle control ECU |
| Main body ECU (Multiplex network body ECU) | |
| No. 2 skid control ECU (Brake actuator assembly) |
When removing the related part to check it, be sure to follow the appropriate procedures and precautions.
Hybrid vehicle control ECU
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID VEHICLE CONTROL ECU>REMOVAL
Main body ECU (Multiplex network body ECU)
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
No. 2 skid control ECU (Brake actuator assembly)
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model LHD)>REMOVAL
| Result | Proceed to |
|---|---|
| The related part has the correct part number. | A |
| The related part has an incorrect part number. | B |
A
B
Select Health Check on the GTS screen and check if system DTCs of the related part are output.
If system DTCs of the related part are stored, assist map writing to the power steering ECU (rack and pinion power steering gear assembly) may not be performed properly.
| Result | Proceed to |
|---|---|
| System DTCs of the related part are output. | A |
| System DTCs of the related part are not output. | B |
A
B
Replace the related part with one that has the correct part number.
Hybrid vehicle control ECU
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID VEHICLE CONTROL ECU>REMOVAL
Main body ECU (Multiplex network body ECU)
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
No. 2 skid control ECU (Brake actuator assembly)
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model LHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
A
B