Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM37A0E _56 Audio / Visual / Telematics _086880 PARK ASSIST / MONITORING _0420015 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB2  Short to GND in Outer Mirror Indicator(Master)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH (master) detects a short to ground in the outer rear view mirror indicator LH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB2 Short to GND in Outer Mirror Indicator(Master)
Both of the following conditions are met:
·

The blind spot monitor system is on


·

The current that is sent from the blind spot monitor sensor to the indicator is above a specified level for a specified period of time


·

Outer mirror LH

·

Outer rear view mirror assembly LH

·

Harness or connector

·

Blind spot monitor sensor LH (master)

·

Outer mirror control ECU assembly LH*



*: w/ Seat Position Memory System


WIRING DIAGRAM

w/ Seat Position Memory System
E399045E18
2.854,0.438 3.01,0.635 0.156,0.198 10 false 8 2.813,0.958 3.073,1.177 0.26,0.219 10 false 12 4.51,0.427 4.771,0.646 0.26,0.219 10 false 13 4.604,0.948 4.865,1.167 0.26,0.219 10 false 7 4.458,0.635 4.781,0.854 0.323,0.219 10 false J23 4.479,1.156 4.802,1.375 0.323,0.219 10 false J23 2.781,1.167 3.188,1.385 0.406,0.219 10 false z17 2.781,0.625 3.188,0.844 0.406,0.219 10 false z17 3.198,0.656 3.656,0.896 0.458,0.24 10 false BSL+ 3.958,0.656 4.365,0.875 0.406,0.219 10 false BDSL 4,1.156 4.406,1.375 0.406,0.219 10 false GND 3.208,1.156 3.615,1.375 0.406,0.219 10 false - 0.167,2.406 2.25,2.792 2.083,0.385 10 false Outer Rear View Mirror Assembly LH 3.094,2.5 4.667,2.823 1.573,0.323 10 false Outer Mirror Control ECU Assembly LH 5.5,2.688 7.156,3.042 1.656,0.354 10 false Blind Spot Monitor Sensor LH (Master) 5.313,0.5 5.573,0.719 0.26,0.219 10 false 4 5.583,0.677 6.031,0.896 0.448,0.219 10 false OMIL 5.5,2.5 5.938,2.76 0.438,0.26 10 false M43 0.469,1.635 2.552,2.021 2.083,0.385 10 false Outer Mirror LH 0.469,1.5 1.083,1.698 0.615,0.198 10 false IND2

w/o Seat Position Memory System
E407665E13
2.094,0.885 2.708,1.083 0.615,0.198 10 false BSL+ 2.365,1.427 2.542,1.615 0.177,0.188 10 false E 2.604,0.896 2.813,1.135 0.208,0.24 10 false 3 2.594,1.438 2.802,1.677 0.208,0.24 10 false 11 5.073,0.917 5.281,1.156 0.208,0.24 10 false 4 5.25,1.01 5.865,1.208 0.615,0.198 10 false OMIL 5.104,2.677 5.719,2.875 0.615,0.198 10 false M43 5.104,2.833 6.75,3.188 1.646,0.354 10 false Blind Spot Monitor Sensor LH (Master) 0.781,2.656 1.396,2.854 0.615,0.198 10 false J31 0.76,2.802 2.865,3.177 2.104,0.375 10 false Outer Rear View Mirror Assembly LH 0.927,1.99 3.031,2.365 2.104,0.375 10 false Outer Mirror LH 0.927,1.823 1.542,2.021 0.615,0.198 10 false IND2

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is turned on.


PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON.


c.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313
OK:

No DTCs are output.



Result:
Result Proceed to
OK A
NG (w/ Seat Position Memory System) B
NG (w/o Seat Position Memory System) C



A

B

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (MASTER) - OUTER MIRROR CONTROL ECU ASSEMBLY LH)

C

6.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (MASTER) - OUTER REAR VIEW MIRROR ASSEMBLY LH)
2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (MASTER) - OUTER MIRROR CONTROL ECU ASSEMBLY LH)
a.

Disconnect the M43 blind spot monitor sensor LH (master) connector.


b.

Disconnect the J23 outer mirror control ECU assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M43-4 (OMIL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY LH
a.

Disconnect the J23 outer mirror control ECU assembly LH connector.


b.
E406225C08
2.167,0.25 2.667,0.5 0.5,0.25 2.146,1.25 2.365,1.698 true 1.958,1.115 1.667,1.708 true 2.292,0.292 2.594,0.49 0.302,0.198 10 false J23 2.229,1.708 2.708,1.906 0.479,0.198 10 false BDSL 0.094,0.031 0.292,0.229 0.198,0.198 10 false *a 1.49,1.708 1.969,1.906 0.479,0.198 10 false GND
*a Component without harness connected
(Outer Mirror Control ECU Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J23-13 (BDSL) - J23-7 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT OUTER MIRROR LH

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH

4.INSPECT OUTER MIRROR LH

b.

Inspect the outer rear view mirror indicator LH on the outer mirror LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION


Result:
Proceed to
OK
NG



OK

5.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

5.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
a.

Remove the outer rear view mirror assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.

Inspect the outer rear view mirror assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE BLIND SPOT MONITOR SENSOR LH (MASTER)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

6.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (MASTER) - OUTER REAR VIEW MIRROR ASSEMBLY LH)
a.

Disconnect the M43 blind spot monitor sensor LH (master) connector.


b.

Disconnect the J31 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M43-4 (OMIL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT OUTER MIRROR LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT OUTER MIRROR LH


Result:
Proceed to
OK
NG



OK

8.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

8.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
a.

Remove the outer rear view mirror assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.

Inspect the outer rear view mirror assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE BLIND SPOT MONITOR SENSOR LH (MASTER)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH