Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM37A0E _56 Audio / Visual / Telematics _086880 PARK ASSIST / MONITORING _0420015 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB3  Short to GND in Outer Mirror Indicator(Slave)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH (slave) detects a short to ground in the outer rear view mirror indicator RH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB3 Short to GND in Outer Mirror Indicator(Slave)
Both of the following conditions are met:
·

The blind spot monitor system is on


·

The current that is sent from the blind spot monitor sensor to the indicator is above a specified level for a specified period of time


·

Outer mirror RH

·

Outer rear view mirror assembly RH

·

Harness or connector

·

Blind spot monitor sensor RH (slave)

·

Outer mirror control ECU assembly RH*



*: w/ Seat Position Memory System


WIRING DIAGRAM

w/ Seat Position Memory System
E399045E19
2.833,0.396 2.99,0.594 0.156,0.198 10 false 8 2.781,0.979 3.042,1.198 0.26,0.219 10 false 12 4.51,0.448 4.771,0.667 0.26,0.219 10 false 13 4.552,0.969 4.813,1.188 0.26,0.219 10 false 7 4.5,0.635 4.823,0.854 0.323,0.219 10 false J7 4.5,1.156 4.823,1.375 0.323,0.219 10 false J7 2.781,1.177 3.188,1.396 0.406,0.219 10 false z16 2.771,0.625 3.177,0.844 0.406,0.219 10 false z16 3.188,0.646 3.594,0.865 0.406,0.219 10 false BSR+ 3.896,0.656 4.448,0.948 0.552,0.292 10 false BDSR 4.042,1.177 4.448,1.396 0.406,0.219 10 false GND 3.219,1.156 3.625,1.375 0.406,0.219 10 false - 0.104,2.438 2.188,2.823 2.083,0.385 10 false Outer Rear View Mirror Assembly RH 3.104,2.49 4.677,2.813 1.573,0.323 10 false Outer Mirror Control ECU Assembly RH 5.438,2.677 7.094,3.031 1.656,0.354 10 false Blind Spot Monitor Sensor RH (Slave) 5.354,0.51 5.615,0.729 0.26,0.219 10 false 4 5.552,0.656 6,0.875 0.448,0.219 10 false OMIR 5.417,2.5 5.833,2.698 0.417,0.198 10 false M2 0.448,1.729 2.531,2.115 2.083,0.385 10 false Outer Mirror RH 0.448,1.542 1.063,1.74 0.615,0.198 10 false IND1

w/o Seat Position Memory System
E407665E16
2.073,0.885 2.688,1.083 0.615,0.198 10 false BSR+ 2.354,1.427 2.531,1.615 0.177,0.188 10 false E 2.573,0.865 2.781,1.104 0.208,0.24 10 false 3 2.583,1.427 2.792,1.667 0.208,0.24 10 false 11 5.073,0.917 5.281,1.156 0.208,0.24 10 false 4 5.25,1.01 5.865,1.208 0.615,0.198 10 false OMIR 5.104,2.677 5.719,2.875 0.615,0.198 10 false M2 5.104,2.833 6.75,3.188 1.646,0.354 10 false Blind Spot Monitor Sensor RH (Slave) 0.719,2.615 1.333,2.813 0.615,0.198 10 false J15 0.719,2.76 2.823,3.135 2.104,0.375 10 false Outer Rear View Mirror Assembly RH 0.938,1.802 1.552,2 0.615,0.198 10 false IND1 0.938,1.979 3.042,2.354 2.104,0.375 10 false Outer Mirror RH

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is turned on.


PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON.


c.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
OK:

No DTCs are output.



Result:
Result Proceed to
OK A
NG (w/ Seat Position Memory System) B
NG (w/o Seat Position Memory System) C



A

B

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (SLAVE) - OUTER MIRROR CONTROL ECU ASSEMBLY RH)

C

6.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR ASSEMBLY RH (SLAVE) - OUTER REAR VIEW MIRROR ASSEMBLY RH)
2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (SLAVE) - OUTER MIRROR CONTROL ECU ASSEMBLY RH)
a.

Disconnect the M2 blind spot monitor sensor RH (slave) connector.


b.

Disconnect the J7 outer mirror control ECU assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M2-4 (OMIR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY RH
a.
E406225C09
2.167,0.25 2.667,0.5 0.5,0.25 2.146,1.25 2.365,1.698 true 1.958,1.115 1.667,1.708 true 2.313,0.302 2.615,0.5 0.302,0.198 10 false J7 2.229,1.708 2.708,1.906 0.479,0.198 10 false BDSR 0.094,0.031 0.292,0.229 0.198,0.198 10 false *a 1.49,1.708 1.969,1.906 0.479,0.198 10 false GND
*a Component without harness connected
(Outer Mirror Control ECU Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J7-13 (BDSR) - J7-7 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT OUTER MIRROR RH

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH

4.INSPECT OUTER MIRROR RH

b.

Inspect the outer rear view mirror indicator RH on the outer mirror RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION


Result:
Proceed to
OK
NG



OK

5.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

5.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
a.

Remove the outer rear view mirror assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.

Inspect the outer rear view mirror assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

6.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR ASSEMBLY RH (SLAVE) - OUTER REAR VIEW MIRROR ASSEMBLY RH)
a.

Disconnect the M2 blind spot monitor sensor RH (slave) connector.


b.

Disconnect the J15 outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M2-4 (OMIR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT OUTER MIRROR RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT OUTER MIRROR RH

b.

Inspect the outer rear view mirror indicator RH on the outer mirror RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION


Result:
Proceed to
OK
NG



OK

8.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

8.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
a.

Remove the outer rear view mirror assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.

Inspect the outer rear view mirror assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH