This DTC is stored when the blind spot monitor sensor RH (slave) detects an open in the outer rear view mirror indicator RH.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1AB5 | Open in Outer Mirror Indicator(Slave) | Both of the following conditions are met:
·
The blind spot monitor system is on ·
The current flowing to the indicator is below a specified value when indicator operation voltage is being sent to the indicator |
·
Outer mirror RH ·
Outer rear view mirror assembly RH ·
Harness or connector ·
Blind spot monitor sensor RH (slave) ·
Outer mirror control ECU assembly RH* |
*: w/ Seat Position Memory System
When checking for DTCs, make sure that the blind spot monitor system is turned on.
Turn the ignition switch off.
Turn the ignition switch to ON.
Recheck for DTCs and check if the same DTC is output again.
No DTCs are output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/ Seat Position Memory System) | B |
| NG (w/o Seat Position Memory System) | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Disconnect the M2 blind spot monitor sensor RH (slave) connector.
Disconnect the J7 outer mirror control ECU assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M2-4 (OMIR) - J7-13 (BDSR) | Always | Below 1 Ω |
| J7-7 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the z16 outer rear view mirror assembly RH connector.
| *a | Component without harness connected
(Outer Mirror Control ECU Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J7-13 (BDSR) - z16-8 (BSR+) | Always | Below 1 Ω |
| J7-7 (GND) - z16-12 (-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the outer rear view mirror assembly RH.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL
Inspect the outer rear view mirror assembly RH (outer rear view mirror indicator RH).
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the outer mirror RH.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>REMOVAL
Inspect the outer mirror RH (outer rear view mirror indicator RH).
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M2 blind spot monitor sensor RH (slave) connector.
Disconnect the J15 outer rear view mirror assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M2-4 (OMIR) - J15-3 (BSR+) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the outer rear view mirror assembly RH.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL
Inspect the outer rear view mirror assembly RH (outer rear view mirror indicator RH).
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the outer mirror RH.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>REMOVAL
Inspect the outer mirror RH (outer rear view mirror indicator RH).
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG