The brake pedal load sensing switch (brake pedal support assembly) signal turns on when the brake pedal is depressed with a force exceeding a predetermined level.
The skid control ECU (brake actuator assembly) uses this circuit to detect if the brake pedal is depressed or not.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C00409E | Brake Pedal Switch "A" Stuck On | Either of the following is detected:
·
When the +BS terminal voltage is 9.5 V or higher with the stop light switch signal off, the brake pedal load sensing switch (brake pedal support assembly) signal on, the master cylinder pressure below 0.7 MPa (71.1 kgf/cm2, 101 psi), and the engine speed 500 rpm or higher, the deceleration is below 0.08 G for 10 seconds or more. ·
When the +BS terminal voltage is 9.5 V or higher, the condition that the brake pedal load sensing switch (brake pedal support assembly) signal remains on while the vehicle speed increases from 0 km/h (0 mph) to 30 km/h (19 mph) occurs 5 times in succession. |
·
Brake pedal load sensing switch (brake pedal support assembly) ·
Wire harness and connector ·
Skid control ECU (brake actuator assembly) |
| C00409F | Brake Pedal Switch "A" Stuck Off | Either of the following is detected:
·
When the +BS terminal voltage is from 9.5 to 17.4 V with the stop light switch signal on, the brake pedal load sensing switch (brake pedal support assembly) signal off, and the master cylinder pressure 6 MPa (61.2 kgf/cm2, 870 psi) or more, the deceleration is 0.4 G or more for 1 second or more. ·
When the +BS terminal voltage is from 9.5 to 17.4 V with the stop light switch signal on, the brake pedal load sensing switch (brake pedal support assembly) signal off, and the master cylinder pressure exceeding 6 MPa (61.2 kgf/cm2, 870 psi), the vehicle speed is 0 km/h (0 mph) for 5 seconds or more. |
·
Brake pedal load sensing switch (brake pedal support assembly) ·
Wire harness and connector ·
Skid control ECU (brake actuator assembly) |
Refer to DTC C004013.
After replacing the skid control ECU (brake actuator assembly), perform "Calibration".
When P057111 and/or P057113 is output together with C00409E and/or C00409F, inspect and repair the trouble areas indicated by P057111 and/or P057113 first.
for P057111: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>P057111
for P057113: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>P057113
Check that the stop light switch display and brake pedal load sensing switch (brake pedal support assembly) display observed on the GTS change according to brake pedal operation.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light SW | Stop light switch assembly status
(STP or STP2 terminal input) |
OFF / ON | OFF: Brake pedal released
ON: Brake pedal depressed |
|
| Brake Pedal Load Sensing SW | Brake pedal load sensing switch (brake pedal support assembly) | OFF / ON | OFF: Brake pedal released
ON: Brake pedal depressed |
- |
| Tester Display |
|---|
| Stop Light SW |
| Brake Pedal Load Sensing SW |
The GTS displays OFF / ON according to brake pedal operation.
Slowly depress the brake pedal, and check when the stop light switch assembly and brake pedal load sensing switch (brake pedal support assembly) turn on.
First the stop light switch assembly should turn on, and then the brake pedal load sensing switch (brake pedal support assembly) should turn on.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Turning on of the brake pedal load sensing switch (brake pedal support assembly) is not confirmed.) | B |
| NG (The brake pedal load sensing switch (brake pedal support assembly) turns on first.) | C |
A
B
C
Clear the DTCs.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| DTC C00409E and C00409F are not output. | A |
| DTC C00409E and/or C00409F are output. | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model LHD)>REMOVAL
Turn the ignition switch off.
Inspect the brake pedal load sensing switch (brake pedal support assembly).
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL LOAD SENSING SWITCH>ON-VEHICLE INSPECTION
The brake pedal load sensing switch (brake pedal support assembly) is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the A39 skid control ECU (brake actuator assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A45-2 (FSW+) - A39-28 (FSW+) | Always | Below 1 Ω |
| A45-2 (FSW+) or A39-28 (FSW+) - Body ground | Always | 10 kΩ or higher |
| A45-1 (FSW-) - Body ground | 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model LHD)>REMOVAL
NG
Turn the ignition switch off.
Check the brake pedal height and stop light switch assembly installation.
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for Gasoline Model LHD)>ADJUSTMENT
The brake pedal height and stop light switch assembly installation are normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG