If the entry unlock function does not operate for the driver door only, but the entry lock function operates, the request code is being transmitted properly from the driver door. In this case, there may be a problem related to the unlock sensor (connection between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door)).
for LHD
for RHD
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Entry Function) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.
After repair, confirm that no DTCs are output.
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
Door locks operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check that the entry unlock function.
| *a | Unlock Sensor (Backside) |
| *a | Unlock Sensor (Backside) |
Turn the ignition switch off.
Open and close the driver door.
With the electrical key transmitter sub-assembly outside of the vehicle, press the lock switch of the electrical key transmitter sub-assembly to lock all of the doors.
Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.
Check that the LED of the electrical key transmitter sub-assembly blinks.
Touch the unlock sensor on the backside of the front door outside handle assembly (for driver door) for 2 seconds or more.*
*: Perform this step 3 seconds or more after performing step (3).
When checking the operation of the unlock sensor again, make sure to perform the procedure from step (1).
| Result | Proceed to |
|---|---|
| Entry function does not operate normally | A |
| Entry function operates normally | B |
A
B
for HV Model: Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>CHECK FOR INTERMITTENT PROBLEMS
for Gasoline Model: Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>CHECK FOR INTERMITTENT PROBLEMS
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Door Lock Pos | Front door RH unlock detection switch signal*1 | UNLOCK or LOCK | UNLOCK: Front door RH unlocked
LOCK: Front door RH locked |
- |
| FL Door Lock Pos | Front door LH unlock detection switch signal*2 | UNLOCK or LOCK | UNLOCK: Front door LH unlocked
LOCK: Front door LH locked |
- |
*1: for RHD
*2: for LHD
| Tester Display |
|---|
| FR Door Lock Pos |
| FL Door Lock Pos |
The GTS display changes correctly in response to the lock/unlock operation of the driver door.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Unlock Sensor (Backside) |
| *a | Unlock Sensor (Backside) |
Open and close the driver door.
With the electrical key transmitter sub-assembly outside of the vehicle, press the lock switch of the electrical key transmitter sub-assembly to lock all of the doors.
Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.
Check that the LED of the electrical key transmitter sub-assembly blinks.
Read the Data List according to the display on the GTS.
Touch the unlock sensor on the backside of the front door outside handle assembly (for driver door) for 2 seconds or more.*
*: Perform this step 3 seconds or more after performing step (f).
When checking the operation of the unlock sensor again, make sure to perform the procedure from step (a).
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| D-Door Touch Sensor | Driver door touch sensor (unlock sensor) | OFF or ON | OFF: Driver door touch sensor (unlock sensor) not touched
ON: Driver door touch sensor (unlock sensor) touched |
·
Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily). ·
Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate. |
| Tester Display |
|---|
| D-Door Touch Sensor |
The GTS display changes correctly in response to the operation of the front door outside handle assembly (for driver door).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M5 certification ECU (smart key ECU assembly) connector.
Disconnect the J25*1 or J9*2 front door outside handle assembly (for driver door) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M5-17 (CLG1) - J25-6 (ANT1) | Always | Below 1 Ω |
| M5-16 (CG1B) - J25-4 (ANT2) | Always | Below 1 Ω |
| M5-17 (CLG1) or J25-6 (ANT1) - Other terminals and body ground | Always | 10 kΩ or higher |
| M5-16 (CG1B) or J25-4 (ANT2) - Other terminals and body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M5-17 (CLG1) - J9-6 (ANT1) | Always | Below 1 Ω |
| M5-16 (CG1B) - J9-4 (ANT2) | Always | Below 1 Ω |
| M5-17 (CLG1) or J9-6 (ANT1) - Other terminals and body ground | Always | 10 kΩ or higher |
| M5-16 (CG1B) or J9-4 (ANT2) - Other terminals and body ground | Always | 10 kΩ or higher |
Reconnect the J25*1 or J9*2 front door outside handle assembly (for driver door) connector.
*1: for LHD
*2: for RHD
Reconnect the M5 certification ECU (smart key ECU assembly) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Unlock Sensor (Backside) |
| *a | Unlock Sensor (Backside) |
Open and close the driver door.
With the electrical key transmitter sub-assembly outside of the vehicle, press the lock switch of the electrical key transmitter sub-assembly to lock all of the doors.
Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.
Check that the LED of the electrical key transmitter sub-assembly blinks.
Read the Data List according to the display on the GTS.
Touch the unlock sensor on the backside of the front door outside handle assembly (for driver door) for 2 seconds or more.*
*: Perform this step 3 seconds or more after performing step (g).
When checking the operation of the unlock sensor again, make sure to perform the procedure from step (a).
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| D-Door Touch Sensor | Driver door touch sensor (unlock sensor) | OFF or ON | OFF: Driver door touch sensor (unlock sensor) not touched
ON: Driver door touch sensor (unlock sensor) touched |
·
Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily). ·
Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate. |
| Tester Display |
|---|
| D-Door Touch Sensor |
The GTS display changes correctly in response to the operation of the front door outside handle assembly (for driver door).
| Proceed to |
|---|
| OK |
| NG |
OK
NG