The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rack and pinion power steering gear assembly removal/installation are shown below.
| *a | An Object Exceeding Weight Limit of Engine Lifter |
The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.
1. PRECAUTION
When handling the rack and pinion power steering gear assembly:
Do not subject the rack and pinion power steering gear assembly (especially the motor and torque sensor) to any impact. Replace the rack and pinion power steering gear assembly with a new one if subjected to a strong impact.
Do not pull the wire harness when moving the rack and pinion power steering gear assembly.
When the rack and pinion power steering gear assembly has been replaced, perform assist map writing and torque sensor zero point calibration.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION
When disconnecting or reconnecting the connectors:
Before disconnecting connectors related to the power steering system, turn the ignition switch to ON, center the steering wheel, turn the ignition switch off, and then disconnect the connectors.
Before reconnecting connectors related to the power steering system, ensure that the ignition switch is off. Then center the steering wheel and turn the ignition switch to ON.
Do not turn the ignition switch to ON when the steering wheel is not centered.
If the above operations are not carried out properly, the steering center point (zero point) will deviate, which may lead to a difference in steering effort between turning right and left.
If there is a difference in steering effort between turning right and left, perform torque sensor zero point calibration.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION
2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
3. SECURE STEERING WHEEL
Secure the steering wheel with the seat belt in order to prevent rotation.
This operation is useful to prevent damage to the spiral cable.
4.REMOVE FRONT WHEELS
45220
5.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY
| *a | Matchmark |
Remove the bolt and slide the steering intermediate shaft assembly.
Do not separate the steering intermediate shaft assembly from the rack and pinion power steering gear assembly.
Put matchmarks on the rack and pinion power steering gear assembly and steering intermediate shaft assembly.
Separate the steering intermediate shaft assembly from the rack and pinion power steering gear assembly.
45470
6.SEPARATE TIE ROD ASSEMBLY LH
Remove the cotter pin and nut.
Install SST to the tie rod assembly LH as shown in the illustration.
Make sure that the upper ends of the tie rod assembly LH and SST are aligned.
Using SST, separate the tie rod assembly LH from the steering knuckle LH as shown in the illustration.
| *a | String | *b | Molybdenum Grease Application Area |
| *c | Place wrench here | *d | Center Nut |
| *e | Spacer | - | - |
|
Turn | - | - |
Apply molybdenum grease to the threads and end of the SST bolt.
Be sure to tighten the string firmly to secure SST to the steering knuckle LH to prevent SST from falling off.
Install SST with the center nut so that (A) and (B) shown in the illustration are parallel. Otherwise, the ball joint dust cover may be damaged.
Be sure to place the wrench on the part shown in the illustration.
Do not damage the front disc brake dust cover.
Do not damage the ball joint dust cover.
Do not damage the steering knuckle LH.
Make sure that SST is securely positioned on the spacer.
If the steering knuckle spacer has come off, replace the steering knuckle with a new one.
45460
7.SEPARATE TIE ROD ASSEMBLY RH
Perform the same procedure as for the LH side.
8.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
for A25A-FXS, A25B-FXS: Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
45319
9.REMOVE STEERING GEAR HEAT INSULATOR (for LHD)
Remove the 2 bolts and steering gear heat insulator from the rack and pinion power steering gear assembly.
10.DISCONNECT WIRE HARNESS (for LHD)
Disconnect the wire harness connector from the rack and pinion power steering gear assembly.
Release the lock before rotating the lock lever.
Remove the 2 bolts and separate the wire harness from the rack and pinion power steering gear assembly.
11.DISCONNECT WIRE HARNESS (for RHD)
Disconnect the wire harness connector from the rack and pinion power steering gear assembly.
Release the lock before rotating the lock lever.
Remove the bolt and separate the wire harness from the rack and pinion power steering gear assembly.
23825
12.REMOVE FUEL DELIVERY GUARD (for A25A-FXS, A25B-FXS)
13.INSTALL ENGINE HANGERS
for A25A-FXS, A25B-FXS: Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
14.REMOVE FRONT FRAME ASSEMBLY
15.REMOVE FRONT STABILIZER BAR SUB-ASSEMBLY WITH LINK
Remove the 4 bolts and front stabilizer bar sub-assembly with the 2 front stabilizer links from the front frame assembly.
44250
16.REMOVE RACK AND PINION POWER STEERING GEAR ASSEMBLY
Remove the 4 bolts, 4 nuts and rack and pinion power steering gear assembly from the front frame assembly.
Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.
44250
17.SECURE RACK AND PINION POWER STEERING GEAR ASSEMBLY
| *a | Protective Tape |
Using SST, secure the rack and pinion power steering gear assembly in a vise.
Wrap SST with protective tape before use.
45470
18.REMOVE TIE ROD ASSEMBLY LH
| *a | Matchmark |
Put matchmarks on the tie rod assembly LH and rack and pinion power steering gear assembly.
Remove the tie rod assembly LH and lock nut.
45460
19.REMOVE TIE ROD ASSEMBLY RH
Perform the same procedure as for the LH side.
45319
20.REMOVE STEERING GEAR HEAT INSULATOR (for RHD)
Remove the 3 bolts and steering gear heat insulator from the rack and pinion power steering gear assembly.