Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL (for Gasoline Model RHD) › from 2020.11
RM37A0E _54 Brake _086869 BRAKE SYSTEM (OTHER) _0449075 BRAKE PEDAL(for Gasoline Model RHD) A

BRAKE SYSTEM (OTHER)  BRAKE PEDAL(for Gasoline Model RHD)  INSTALLATION  


PROCEDURE

Hide 47121 1.INSTALL BRAKE PEDAL PAD

a.

Install the brake pedal pad to the brake pedal support assembly.

HINT:

Installation is easier after applying a small amount of soapy water.



Hide 84345 2.INSTALL STOP LIGHT SWITCH MOUNTING ADJUSTER

a.

Engage the 2 claws to install the stop light switch mounting adjuster.


Hide 47101A 3.INSTALL BRAKE PEDAL RETURN SPRING

a.
C447471C01
0,0 0,0 false
V100136

Up
V100137

Front of the Vehicle


Install the brake pedal return spring to the brake pedal support assembly.

NOTICE:

Attach the bottom part of the brake pedal return spring first, making sure that the open part of the hook is facing the front of the vehicle. Attach the top part of the brake pedal return spring second, making sure that the open part of the hook is facing the rear of the vehicle.



Hide 4.INSTALL BRAKE PEDAL SUPPORT ASSEMBLY

a.

Push the brake booster with master cylinder toward the engine compartment, and install the brake pedal support assembly while avoiding the stud bolts of the brake pedal support base.

NOTICE:
·

Be careful not to deform the bracket of the instrument panel reinforcement assembly.

·

Do not apply excessive force to the brake lines.

·

Do not apply excessive force to the wire harness.




b.

Return the brake booster with master cylinder to its original position.


c.

Install the brake pedal support assembly with the 4 nuts.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


d.

Install the brake pedal support assembly to the instrument panel reinforcement assembly with the bolt.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


e.

Engage the 2 clamps to install the wire harness to the brake pedal support assembly.


f.

Connect the connector.


Hide 47264A 5.INSTALL PUSH ROD PIN

a.
C319792C01
0,0 0,0 false
V100144

Lithium Soap Base Glycol Grease


Apply lithium soap base glycol grease to the push rod pin.


b.
C447462

Connect the brake master cylinder push rod clevis to the brake pedal support assembly with the push rod pin, and install a new clip as shown in the illustration.

HINT:

The push rod pin can be installed in either direction.



Hide 84340 6.INSTALL STOP LIGHT SWITCH ASSEMBLY

Hide 73900 7.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 55045 9.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

Hide 53601 10.CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

Hide 11.CONNECT BRAKE LINE

a.
C447366C01
2.885,2.896 2.708,2.896 2.708,2.896 2.708,2.646 false 1.792,2.927 2.104,3.083 0.313,0.156 10 false *a 2.906,2.823 3.219,2.979 0.313,0.156 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, connect the 2 brake lines to the brake master cylinder sub-assembly.

Torque:
Specified tightening torque : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

17.4 N*m (177 kgf*cm, 13 ft.*lbf)




Hide 55606 14.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 62111A 15.INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 67913 16.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 55704B 17.INSTALL COWL VENTILATOR PANEL SUB-ASSEMBLY