Home › Drivetrain › UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › OIL COOLER › from 2020.11
RM37A0E _52 Drivetrain _094409 UA80E AUTOMATIC TRANSMISSION / TRANSAXLE _0449681 OIL COOLER A

UA80E AUTOMATIC TRANSMISSION / TRANSAXLE  OIL COOLER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission oil cooler removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted Stop and Start System (Click here)
Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Replacement of battery
·

Integrated Current Value Initialization

·

Switch Battery Type


Stop and Start System (Click here)
Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)

CAUTION:
A370840

Do not remove the radiator cap sub-assembly, cylinder block drain cock plug or radiator drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 53852B 1.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

Hide 53851D 2.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

Hide 51441 3.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51444A 4.REMOVE REAR ENGINE UNDER COVER LH

Hide 53737B 5.REMOVE FRONT FENDER APRON SEAL LH

Hide 53295E 6.REMOVE COOL AIR INTAKE DUCT SEAL

Hide 17750A 7.REMOVE INLET AIR CLEANER ASSEMBLY

Hide 17700 8.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Hide 9.REMOVE BATTERY

Hide 74404B 10.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 11.DRAIN ENGINE COOLANT

Hide 33197C 13.REMOVE TRANSMISSION BREATHER CLAMP

a.
C426647

Disengage the 3 clamps to remove the transmission breather clamp.


Hide 16260 14.DISCONNECT WATER BY-PASS HOSE ASSEMBLY

a.
C426648

Slide the 2 clips and disconnect the water by-pass hose assembly from the transmission oil cooler.

HINT:

Use a container to catch any coolant which flows out of the water by-pass hose assembly and transmission oil cooler.



Hide 32941A 15.DISCONNECT INLET NO. 2 OIL COOLER HOSE

a.
C426649

Slide the clip and disconnect the inlet No. 2 oil cooler hose from the transmission oil cooler.

HINT:

Use a container to catch any automatic transaxle fluid which flows out of the inlet No. 2 oil cooler hose and transmission oil cooler.



Hide 32942B 16.DISCONNECT OUTLET NO. 3 OIL COOLER HOSE

a.
C426650

Slide the clip and disconnect the outlet No. 3 oil cooler hose from the transmission oil cooler.

HINT:

Use a container to catch any automatic transaxle fluid which flows out of the outlet No. 3 oil cooler hose and transmission oil cooler.



Hide 33493A 17.REMOVE TRANSMISSION OIL COOLER

a.
C426638

Disengage the wire harness clamp.


b.
C426651

Remove the 3 bolts and transmission oil cooler from the automatic transaxle case sub-assembly.

HINT:

Use a container to catch any coolant and automatic transaxle fluid which flow out of the transmission oil cooler.



Hide 32943C 18.DISCONNECT NO. 3 TRANSMISSION OIL COOLER HOSE

HINT:

Perform this procedure only when replacement of the No. 1 oil cooler tube sub-assembly without hose is necessary.


a.
C426652

Slide the clip and disconnect the No. 3 transmission oil cooler hose from the No. 1 oil cooler tube sub-assembly without hose.


Hide 32907C 19.REMOVE NO. 1 OIL COOLER TUBE SUB-ASSEMBLY WITHOUT HOSE

HINT:

Perform this procedure only when replacement of the No. 1 oil cooler tube sub-assembly without hose is necessary.


a.
C426653C01
1.469,1.896 1.615,2.042 1.615,2.042 1.865,2.042 false 1.917,1.938 2.229,2.094 0.313,0.156 10 false *1
*1 Inlet No. 1 Oil Cooler Hose


Slide the clip and disconnect the inlet No. 1 oil cooler hose from the oil cooler outlet union or elbow.

HINT:

Use a container to catch any automatic transaxle fluid which flows out of the inlet No. 1 oil cooler hose and oil cooler outlet union or elbow.



b.

Remove the 2 bolts and No. 1 oil cooler tube sub-assembly without hose from the automatic transaxle case sub-assembly.


c.
C426654C01
1.292,1.771 1.375,1.99 1.375,1.99 1.604,1.99 false 2.948,0.156 2.74,0.156 2.74,0.156 2.604,0.583 false 2.688,0.927 2.771,1.146 2.771,1.146 3,1.146 false 1.406,0.542 1.333,0.271 1.333,0.271 1.104,0.271 false 1.635,1.875 1.948,2.031 0.313,0.156 10 false *1 2.979,0.063 3.292,0.219 0.313,0.156 10 false *2 3.031,1.042 3.281,1.24 0.25,0.198 10 false *3 0.938,0.167 1.25,0.323 0.313,0.156 10 false *4
*1 Inlet No. 1 Oil Cooler Hose
*2 Inlet No. 2 Oil Cooler Hose
*3 Outlet No. 3 Oil Cooler Hose
*4 No. 1 Oil Cooler Tube Sub-assembly without Hose


Slide the 3 clips and remove the inlet No. 1 oil cooler hose, inlet No. 2 oil cooler hose and outlet No. 3 oil cooler hose from the No. 1 oil cooler tube sub-assembly without hose.