Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT AIR CONDITIONING UNIT (for HV Model) › from 2020.11
RM37A0E _58 Vehicle Interior _086896 HEATING / AIR CONDITIONING _0417361 FRONT AIR CONDITIONING UNIT(for HV Model) A

HEATING / AIR CONDITIONING  FRONT AIR CONDITIONING UNIT(for HV Model)  INSTALLATION  


PROCEDURE

Hide 1.TEMPORARILY INSTALL AIR CONDITIONER UNIT ASSEMBLY

a.

Temporarily install the air conditioner unit assembly to the instrument panel reinforcement assembly with the 3 bolts.


Hide 55835A 2.INSTALL CENTER HEATER TO REGISTER DUCT

a.

Engage the 6 claws to install the center heater to register duct.


Hide 3.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY

NOTICE:
·

Be sure to support the air conditioner unit assembly when installing it. Failure to do so may cause the bracket of the air conditioner unit assembly to break.

·

When installing the air conditioner unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



a.

for LHD:

i.

Connect the 4 connectors.

E431667C01
0,0 0,0 false
V113147

Install in this Direction - -



ii.

Engage each clamp.


iii.

Temporarily install the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.



b.

for RHD:

i.

Connect the 4 connectors.

E455726C01
0,0 0,0 false
V113147

Install in this Direction - -



ii.

Engage each clamp.


iii.

Temporarily install the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.



c.

Install the 4 bolts (A).

E431665C02
0,0 0,0 false
V100135

Bolt (A)
V100136

Bolt (B)
V100137

Nut - -


Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


d.

Connect the brake pedal assembly with the bolt (B).

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


e.

Temporarily install the nut.


f.

Install the 3 bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


g.

Install the 2 hole plugs.


h.
E431660C01
0.448,1.094 0.583,0.865 false 0.354,1.094 0.583,1.313 0.229,0.219 10 false *a
*a Lip


Install a new cooler unit drain hose grommet.

NOTICE:
·

If the drain cooler hose is disconnected from the cooler unit drain hose grommet, make sure to replace the cooler unit drain hose grommet with a new one. Failure to do so may lead to water ingress.

·

Make sure that the entire lip of the cooler unit drain hose grommet is securely engaged to the vehicle body.




i.

Connect the drain cooler hose.


j.

Install the clip.


Hide 55307C 4.INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

Install the No. 2 instrument panel brace sub-assembly with the bolt and nut.

Torque:
Bolt : 20 N*m (204 kgf*cm, 15 ft.*lbf)
Nut : 18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Temporarily install the screw.

HINT:

Do not fully tighten the screw.



Hide 55306A 5.INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

Install the No. 1 instrument panel brace sub-assembly with the bolt and nut.

Torque:
Bolt : 20 N*m (204 kgf*cm, 15 ft.*lbf)
Nut : 18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Temporarily install the screw.

HINT:

Do not fully tighten the screw.



Hide 6.INSTALL AIR CONDITIONER UNIT ASSEMBLY

a.

for LHD:

i.

Tighten the 3 bolts, 2 screws and nut to install the air conditioner unit assembly.

E431672C01
0.635,0.573 0.792,0.771 0.156,0.198 10 true 1 6.354,0.417 6.51,0.615 0.156,0.198 10 true 2 3.021,0.563 3.177,0.76 0.156,0.198 10 true 3 0.958,5.135 1.115,5.333 0.156,0.198 10 true 4 3.302,4.656 3.458,4.854 0.156,0.198 10 true 5 5.479,3.958 5.635,4.156 0.156,0.198 10 true 6
V100135

Bolt
V100136

Screw
V100137

Nut - -


Torque:
Bolt : 9.8 N*m (100 kgf*cm, 87 in.*lbf)
Nut : 9.8 N*m (100 kgf*cm, 87 in.*lbf)

NOTICE:

Tighten the bolts, screws and nut in the order shown in the illustration.




b.

for RHD:

i.

Tighten the 3 bolts, 2 screws and nut to install the air conditioner unit assembly.

E455727C01
3.083,0.448 3.24,0.646 0.156,0.198 10 true 1 0.583,0.385 0.74,0.583 0.156,0.198 10 true 2 6.333,0.354 6.49,0.552 0.156,0.198 10 true 3 6.104,4.552 6.26,4.75 0.156,0.198 10 true 4 5.073,4.573 5.229,4.771 0.156,0.198 10 true 5 1.635,4.854 1.792,5.052 0.156,0.198 10 true 6
V100135

Bolt
V100136

Screw
V100137

Nut - -


Torque:
Bolt : 9.8 N*m (100 kgf*cm, 87 in.*lbf)
Nut : 9.8 N*m (100 kgf*cm, 87 in.*lbf)

NOTICE:

Tighten the bolts, screws and nut in the order shown in the illustration.




Hide 7.CONNECT INSTRUMENT PANEL WIRE (for LHD)

a.

Connect the earth wire with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Engage each clamp.


c.

Connect the 2 connectors.


d.

Engage each clamp.


e.

Install the 2 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


f.

Connect the connector holder with the bolt (B).

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


g.

Connect the 4 earth wires with the 4 bolts (A).

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


h.

Connect the connector.


Hide 8.CONNECT INSTRUMENT PANEL WIRE (for RHD)

a.

Connect the earth wire with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Engage each clamp.


c.

Connect the 2 connectors.


d.

Engage each clamp.


e.

Connect the connector holder with the nut (B).

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


f.

Install the 2 nuts (A).

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


g.

Connect the 4 earth wires with the 4 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


h.

Connect the connector.


Hide 55837C 9.INSTALL CENTER HEATER TO REGISTER SUB DUCT

a.

Engage the guide.


b.

Install the center heater to register sub duct with the 2 screws.


Hide 55215D 10.INSTALL NO. 3 DASH PANEL INSULATOR PAD

a.

Install the No. 3 dash panel insulator pad.


Hide 87212G 11.INSTALL REAR NO. 3 AIR DUCT

a.

Engage the 4 claws to install the rear No. 3 air duct.


Hide 87212H 12.INSTALL REAR NO. 4 AIR DUCT

a.

Engage the 4 claws.


b.

Install the rear No. 4 air duct with the clip.


c.
E431650

Install the front floor carpet assembly to the original position as shown in the illustration.


d.

Engage the 4 guides.


Hide 87212 13.INSTALL REAR NO. 1 AIR DUCT

a.

Engage the 4 claws to install the rear No. 1 air duct.


Hide 87212F 14.INSTALL REAR NO. 2 AIR DUCT

a.

Engage the 4 claws.


b.

Install the rear No. 2 air duct with the clip.


c.
E431646

Install the front floor carpet assembly to the original position as shown in the illustration.


d.

Engage the 4 guides.


Hide 88625Q 17.INSTALL COOLER (ROOM TEMP. SENSOR) THERMISTOR

a.

Connect the aspirator and connector to install the cooler (room temp. sensor) thermistor.


Hide 89343C 18.INSTALL NO. 1 CLEARANCE WARNING BUZZER (for LHD)

Hide 82877 20.INSTALL ECU INTEGRATION BOX RH (for LHD)

Hide 82877 21.INSTALL ECU INTEGRATION BOX RH (for RHD)

Hide 45250 22.INSTALL STEERING COLUMN ASSEMBLY

Hide 87201L 23.INSTALL NO. 4 AIR DUCT SUB-ASSEMBLY

Hide 83108 24.INSTALL METER MIRROR SUB-ASSEMBLY (w/ Headup Display)

Hide 25.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU

Hide 26.INSTALL FRONT SEAT ASSEMBLY RH (for Manual Seat)

Hide 27.INSTALL FRONT SEAT ASSEMBLY (for Power Seat)

Hide 87245B 28.CONNECT INLET HEATER WATER HOSE B

a.
E431223C01
1.74,2.865 2.156,2.448 false 0.083,2.25 0.729,2.656 0.646,0.406 10 false *a 2.177,2.354 2.49,2.51 0.313,0.156 10 false *b 1.115,1.094 1.333,1.292 0.219,0.198 10 true A 2.844,3.313 3.156,3.469 0.313,0.156 10 false *c 0.438,3.271 0.75,3.427 0.313,0.156 10 false *c 1.031,4.271 1.344,4.427 0.313,0.156 10 false *d 2.302,4.24 2.615,4.396 0.313,0.156 10 false *d
*a View A
*b Marking (White)
*c Clip Installation Angle (60°)
*d 60°


Connect the inlet heater water hose B with the marking facing up and engage the clip within the area shown in the illustration.

NOTICE:

Do not apply excessive force to the inlet heater water hose B.



Hide 87246B 29.CONNECT OUTLET HEATER WATER HOSE B

a.
E431221C01
1.75,3.073 2.031,2.927 false 0.083,2.25 0.396,2.406 0.313,0.156 10 false *a 2.063,2.833 2.375,2.99 0.313,0.156 10 false *b 1.635,2.333 1.948,2.49 0.313,0.156 10 false *c 1.135,1.208 1.344,1.406 0.208,0.198 10 true A
*a View A
*b Marking (Yellow)
*c Clip Installation Angle (270°)


Connect the outlet heater water hose B with the marking facing up and engage the clip within the area shown in the illustration.

NOTICE:

Do not apply excessive force to the outlet heater water hose B.



Hide 88716A 30.CONNECT COOLER REFRIGERANT LIQUID PIPE A (w/o Sub-cool Accelerator)

a.

Remove the vinyl tape from the cooler refrigerant liquid pipe A.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler refrigerant liquid pipe A.

Compressor Oil:

ND-OIL 11 or equivalent



c.

Install the O-ring to the cooler refrigerant liquid pipe A.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.

Connect the cooler refrigerant liquid pipe A.


Hide 88707 31.CONNECT SUCTION PIPE SUB-ASSEMBLY (w/o Sub-cool Accelerator)

a.

Remove the vinyl tape from the suction pipe sub-assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction pipe sub-assembly.

Compressor Oil:

ND-OIL 11 or equivalent



c.

Install the O-ring to the suction pipe sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.

Connect the suction pipe sub-assembly.


e.
E431226

Rotate the hook connector as shown in the illustration.


f.

Insert the tube joint into the fitting hole securely and install the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 88710G 32.CONNECT NO. 2 AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY (w/ Sub-cool Accelerator)

a.

Remove the vinyl tape from the No. 2 air conditioner tube and accessory assembly.


b.

Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces of the No. 2 air conditioner tube and accessory assembly.

Compressor Oil:

ND-OIL 11 or equivalent



c.

Install the 2 O-rings to the No. 2 air conditioner tube and accessory assembly.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free of foreign matter.



d.

Connect the No. 2 air conditioner tube and accessory assembly.


e.
E455720

Rotate the hook connector as shown in the illustration.


f.

Insert the tube joint into the fitting hole securely and install the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 55704B 33.INSTALL COWL VENTILATOR PANEL SUB-ASSEMBLY (for LHD)

Hide 55704B 34.INSTALL COWL VENTILATOR PANEL SUB-ASSEMBLY (for RHD)

Hide 53608A 35.INSTALL FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY LH

Hide 53607B 36.INSTALL FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 53892C 37.INSTALL FRONT FENDER SPLASH SHIELD SEAL FRONT LH

Hide 53891C 38.INSTALL FRONT FENDER SPLASH SHEILD SEAL FRONT RH

HINT:

Perform the same procedure as for the LH side.


Hide 53808A 39.INSTALL FENDER SPLASH SHIELD SUB-ASSEMBLY REAR LH

Hide 53807A 40.INSTALL FENDER SPLASH SHIELD SUB-ASSEMBLY REAR RH

HINT:

Perform the same procedure as for the LH side.


Hide 41.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 44.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT