Home › Vehicle Interior › SEAT BELT › REAR NO. 1 SEAT OUTER BELT ASSEMBLY › from 2020.11
RM37A0E _58 Vehicle Interior _086895 SEAT BELT _0417486 REAR NO. 1 SEAT OUTER BELT ASSEMBLY A

SEAT BELT  REAR NO. 1 SEAT OUTER BELT ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front seat inner belt assembly removal/installation are shown below.

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted Stop and Start System (Click here)
Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY

Hide 58409A 3.REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY (w/o Woofer)

Hide 64910J 4.REMOVE TONNEAU COVER ASSEMBLY

Hide 5.REMOVE CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 58441L 6.REMOVE BATTERY SERVICE HOLE COVER

Hide 64993 7.REMOVE REAR DECK FLOOR BOX

Hide 64742C 8.REMOVE DECK SIDE TRIM BOX LH (w/o Woofer)

Hide 58387B 9.REMOVE REAR FLOOR FINISH PLATE

Hide 10.REMOVE REAR NO. 2 SEAT ASSEMBLY

Hide 72138M 11.REMOVE REAR OUTER SEAT TRACK BRACKET COVER

Hide 67918A 12.REMOVE REAR DOOR SCUFF PLATE

Hide 13.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

a.

Disconnect the rear door opening trim weatherstrip.


Hide 64713F 14.REMOVE FRONT DECK SIDE TRIM COVER LH (for LH Side)

Hide 64712F 15.REMOVE FRONT DECK SIDE TRIM COVER RH (for RH Side)

Hide 73370E 16.DISCONNECT REAR SEAT OUTER BELT ASSEMBLY

a.
B564819

Remove the bolt to disconnect the floor anchor of the rear seat outer belt assembly.


Hide 64715E 17.REMOVE NO. 2 DECK SIDE TRIM COVER

Hide 73570 18.DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY

Hide 64974 19.REMOVE DECK TRIM POCKET COVER

Hide 64725F 20.REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

Hide 64740C 22.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)

Hide 88625T 23.REMOVE COOLER (NO. 2 ROOM TEMP. SENSOR) THERMISTOR (for RH Side)

Hide 64730B 24.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)

Hide 62639A 25.REMOVE QUARTER PILLAR GARNISH

Hide 73370E 26.REMOVE REAR SEAT OUTER BELT ASSEMBLY

a.
B564820

Loosen the bolt and disconnect the shoulder anchor of the rear seat outer belt assembly.

HINT:

The bolt cannot be removed from the shoulder anchor of the rear seat outer belt assembly.



b.

w/o Pretensioner:

i.
B564821

Remove the 2 bolts.


ii.

Disengage the 2 guides to remove the rear seat outer belt assembly LH.



c.

w/ Pretensioner:

i.
B601262C01
1.219,2.958 1.438,2.677 false 0.656,3.063 0.938,2.813 true 1.375,2.51 1.625,2.719 0.25,0.208 10 false *a 0.542,3.052 0.792,3.26 0.25,0.208 10 false *b 1.01,2.469 1.26,2.677 0.25,0.208 10 false *c
*a Protective Tape
*b Locking Button
*c Release


Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector.

HINT:

Tape the screwdriver tip before use.



ii.
B601263

Remove the 2 bolts.


iii.

Disengage the 2 guides to remove the rear seat outer belt assembly LH.