Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, Gasoline Model) › from 2020.11
RM37A0E _58 Vehicle Interior _086886 THEFT DETERRENT / KEYLESS ENTRY _0419213 ENTRY AND START SYSTEM(for Start Function, Gasoline Model) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, Gasoline Model)  Engine does not Start  


DESCRIPTION

When the electrical key transmitter sub-assembly is in the cabin and the engine switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. Additionally, when the shift lever is in P and the brake pedal is depressed, the engine can be started by pressing the engine switch. If the steering is unlocked, the engine can also be started by pressing the engine switch with the shift lever in N and the brake pedal depressed.

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Engine does not start
Power Source Control
·

Stop Light Switch1

·

Steering Unlock Switch

·

Shift P Signal

·

Neutral SW/ Clutch SW

·

IG Relay Monitor (Inside)

·

IG Relay Monitor (Outside)

·

Latch Circuit

·

Starter Request Signal

·

Power Supply Condition


Entry&Start
·

Immobiliser

·

Engine Start Request

·

L Code Check

·

S Code Check*


Starting Control
·

Starter SW

·

Shift Position P or N

·

Ignition



*: w/ ID Code Box


WIRING DIAGRAM

B542217E02
5.927,0.51 6.385,0.708 0.458,0.198 10 false STP 0.896,0.51 1.354,0.708 0.458,0.198 10 false STP2 0.979,1.917 1.438,2.115 0.458,0.198 10 false STP 1.365,0.385 2.385,0.885 1.021,0.5 10 false 37 1.365,1.813 2.74,2.01 1.375,0.198 10 false 27 5.729,0.385 5.885,0.583 0.156,0.198 10 false 4 0.146,0.885 1.802,1.26 1.656,0.375 10 false A39 0.135,1.042 1.688,1.604 1.552,0.563 10 false Skid Control ECU (Brake Actuator Assembly) 0.146,2.271 1.979,2.469 1.833,0.198 10 false A28 0.677,2.271 1.135,2.469 0.458,0.198 10 false ECM 0.24,3.292 1.104,3.635 0.865,0.344 10 false from Auxiliary Battery 1.656,3.438 2.271,3.635 0.615,0.198 10 false STOP 2.135,3.198 2.292,3.396 0.156,0.198 10 false 7 2.354,3.302 2.51,3.5 0.156,0.198 10 false B 2.135,3.573 2.292,3.771 0.156,0.198 10 false 2 2.344,3.677 2.802,3.875 0.458,0.198 10 false GND 2.781,3.521 3.094,3.719 0.313,0.198 10 false IC 3.313,3.406 3.469,3.604 0.156,0.198 10 false 3 3.083,3.406 3.24,3.604 0.156,0.198 10 false L 2.229,4.083 2.688,4.281 0.458,0.198 10 false A42 2.219,4.24 3.333,4.792 1.115,0.552 10 false Stop Light Switch Assembly 5.833,0.896 6.292,1.094 0.458,0.198 10 false H28 5.823,1.063 6.958,1.813 1.135,0.75 10 false Shift Lock Control Unit Assembly 5.656,3.396 5.969,3.594 0.313,0.198 10 false 25 5.917,3.406 6.531,3.604 0.615,0.198 10 false STP1 6.573,3.573 6.885,3.771 0.313,0.198 10 false IC 5.531,4.229 6.708,4.563 1.177,0.333 10 false M5 5.521,4.385 7.063,4.958 1.542,0.573 10 false Certification ECU (Smart Key ECU Assembly)

B570232E03
0.896,0.854 1.354,1.052 0.458,0.198 10 false NSW 0.927,2.896 1.385,3.094 0.458,0.198 10 false STA 1.375,0.646 1.833,0.844 0.458,0.198 10 false 106 1.375,0.854 1.833,1.052 0.458,0.198 10 false C54 1.375,2.896 1.833,3.094 0.458,0.198 10 false A28 1.417,2.688 1.875,2.885 0.458,0.198 10 false 43 0.656,3.354 1.115,3.552 0.458,0.198 10 false ECM 2.323,1.708 2.781,1.906 0.458,0.198 10 false CLL 2.313,2.063 2.771,2.26 0.458,0.198 10 false STA 2.25,1.458 2.708,1.656 0.458,0.198 10 false 17 2.26,2.302 2.719,2.5 0.458,0.198 10 false 21 2.979,1.542 3.438,1.74 0.458,0.198 10 false A34 2.969,1.708 3.76,2.396 0.792,0.688 10 false Engine Stop and Start ECU* 4.125,1.281 4.583,1.479 0.458,0.198 10 false 4 3.938,1.833 4.396,2.031 0.458,0.198 10 false N 3.938,2.115 4.396,2.313 0.458,0.198 10 false P 4.219,1.542 4.677,1.74 0.458,0.198 10 false B 4.51,1.542 4.969,1.74 0.458,0.198 10 false L 4.792,1.479 5.25,1.677 0.458,0.198 10 false C52 4.792,1.667 5.604,2.385 0.813,0.719 10 false Park/Neutral Position Switch Assembly 4.385,2.375 4.844,2.573 0.458,0.198 10 false 9 5.708,0.719 6.167,0.917 0.458,0.198 10 false 9 5.917,0.719 6.531,0.917 0.615,0.198 10 false STAR 6.229,0.354 6.542,0.552 0.313,0.198 10 false +B 6.563,0.99 6.875,1.188 0.313,0.198 10 false IC 5.635,2.781 6.094,2.979 0.458,0.198 10 false 20 5.917,2.885 6.375,3.083 0.458,0.198 10 false STA 5.583,3.333 6.042,3.531 0.458,0.198 10 false A19 5.573,3.5 7.094,4.135 1.521,0.635 10 false Certification ECU (Smart Key ECU Assembly) 2.979,3.177 3.438,3.375 0.458,0.198 10 false 2 3.219,3.177 3.677,3.375 0.458,0.198 10 false 5 3.99,3.219 5.219,3.417 1.229,0.198 10 false ST NO. 1 2.969,3.875 3.125,4.073 0.156,0.198 10 false 1 3.219,3.875 3.375,4.073 0.156,0.198 10 false 3 3.448,4.146 4.677,4.344 1.229,0.198 10 false ST NO. 2* 3.24,4.531 3.698,4.729 0.458,0.198 10 false C56 4.021,4.531 4.479,4.729 0.458,0.198 10 false C58 3.604,4.521 3.76,4.719 0.156,0.198 10 false 1 4.406,4.521 4.646,4.708 0.24,0.188 10 false 1* 4.646,5.01 5.104,5.208 0.458,0.198 10 false C69 4.719,4.792 4.875,4.99 0.156,0.198 10 false 1 3.417,4.771 3.729,4.969 0.313,0.198 10 false ST 4.021,4.771 4.635,4.969 0.615,0.198 10 false ZYV* 4.417,4.854 4.573,5.052 0.156,0.198 10 false B 5.875,4.99 6.729,5.51 0.854,0.521 10 false from Auxiliary Battery 0.271,5.99 4.396,6.188 4.125,0.198 10 false *: w/ Stop and Start System 3.198,5.594 5.646,5.792 2.448,0.198 10 false Starter Assembly 2.698,3.521 3.01,3.719 0.313,0.198 10 false ST

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the entry and start system (for Start Function) has been disabled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>CUSTOMIZE PARAMETERS

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or an electrical key transmitter sub-assembly, refer to Service Bulletin.

·

After completing repairs, confirm that the problem does not recur.

·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



HINT:
·

If the ignition switch is changed from ON to ACC with the shift lever in any position other than P, and then the shift lever is moved to P and the engine switch is pressed with the brake pedal depressed, the ignition switch will turn off.

·

If the brake pedal is repeatedly depressed while the engine is stopped, the brake booster pressure will be released and the force required to depress the brake pedal to illuminate the stop lights will increase.



PROCEDURE

1.CHECK ENGINE CRANKING OPERATION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

Check that the key indicator display is displayed on the multi-information display in the combination meter assembly, and then press the engine switch and check that the engine cranks.


Result:
Result Proceed to
Engine cranks and initial combustion occurs A
Engine cranks but initial combustion does not occur B
Engine does not crank C



A

B

C

2.CHECK ENGINE SWITCH CONDITION
2.CHECK ENGINE SWITCH CONDITION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

With the brake pedal released, check that pressing the engine switch causes the power source mode to change.


Result:
Result Proceed to
Power source mode changes : Off → ACC → ON → off A
Power source mode does not change to ACC or ON B
Power source mode changes to ON but not to ACC C
Power source mode changes to ACC but not to ON D



A

3.READ VALUE USING GTS (STOP LIGHT SWITCH1)

B

C

D

3.READ VALUE USING GTS (STOP LIGHT SWITCH1)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
·

Use this item to determine if the stop light switch assembly is malfunctioning.

·

The engine cannot be started when this item is OFF.

·

If the stop light switch assembly is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch1
50003 223 3
OK:

The GTS display changes correctly in response to the brake pedal operation.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW, SHIFT POSITION P OR N)

NG

12.INSPECT STOP LIGHT SWITCH ASSEMBLY
4.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW, SHIFT POSITION P OR N)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral SW/ Clutch SW Shift position (P and N) OFF or ON OFF: Shift lever in any position other than P or N
ON: Shift lever in P or N
·

Use this item to determine if the park/neutral position switch assembly is malfunctioning.

·

When the engine cannot be started due to a park/neutral position switch assembly malfunction, OFF is displayed.


Body Electrical > Power Source Control > Data List
Tester Display
Neutral SW/ Clutch SW
50003 223 6
Body Electrical > Starting Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift Position P or N Park/Neutral position switch status OFF or ON OFF: Shift lever not in P or N
ON: Shift lever in P or N
When OFF is displayed, the engine will not crank.
Body Electrical > Starting Control > Data List
Tester Display
Shift Position P or N
50003 221 2
OK:

The GTS display changes correctly in response to the shift lever operation.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (STARTER REQUEST SIGNAL)

NG

14.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
5.READ VALUE USING GTS (STARTER REQUEST SIGNAL)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter Request Signal Engine start request signal status OFF or ON OFF: The engine switch is not pressed
ON: With the shift lever in P and the brake pedal depressed, the engine switch is pressed and held
·

When the engine cannot be started due to a start request signal malfunction, OFF is displayed.

·

When the engine switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the engine switch needs to be pressed and held for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Starter Request Signal
50003 223 12
NOTICE:

Check that the key indicator display is displayed on the multi-information display in the combination meter assembly, and then press the engine switch.


OK:

The GTS display changes correctly in response to the engine switch operation.



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (STARTER REQUEST SIGNAL)

NG

16.CHECK STEERING LOCK FUNCTION
6.READ VALUE USING GTS (STARTER REQUEST SIGNAL)
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

According to the display on the GTS, read the Data List while pressing the engine switch with the brake pedal depressed.

Body Electrical > Starting Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter SW Starter operation request OFF or ON OFF: Starter operation not requested
ON: Starter operation requested
When OFF is displayed, the engine will not crank.
Body Electrical > Starting Control > Data List
Tester Display
Starter SW
50003 221 1
OK:

The GTS display changes.



Result:
Proceed to
OK
NG



OK

7.INSPECT ST RELAY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

7.INSPECT ST RELAY

OK

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)

NG

REPLACE ST RELAY

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)
a.
C378519C02
0.156,0.125 0.521,0.469 0.365,0.344 10 false *1
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
(ST Relay Holder)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
No. 1 engine room relay block and No. 1 junction block assembly ST relay terminal 2 - Body ground Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1.0 V or less


HINT:

*: While the engine is cranking, the auxiliary battery voltage may drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (ST RELAY - AUXILIARY BATTERY AND GROUND)

NG

17.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
9.CHECK HARNESS AND CONNECTOR (ST RELAY - AUXILIARY BATTERY AND GROUND)
a.
C378519C02
0.156,0.125 0.521,0.469 0.365,0.344 10 false *1
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
(ST Relay Holder)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
No. 1 engine room relay block and No. 1 junction block assembly ST relay terminal 1 - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
No. 1 engine room relay block and No. 1 junction block assembly ST relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - ST RELAY)
a.

Disconnect the C56 starter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
No. 1 engine room relay block and No. 1 junction block assembly ST relay terminal 3 - C56-1 Always Below 1 Ω
No. 1 engine room relay block and No. 1 junction block assembly ST relay terminal 3 or C56-1 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - AUXILIARY BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - AUXILIARY BATTERY)
a.

Disconnect the C69 starter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C69-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT STOP LIGHT SWITCH ASSEMBLY

OK

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the M5 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A42 stop light switch assembly connector.


c.

Disconnect the A28 ECM connector.


d.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


e.

Disconnect the H28 shift lock control unit assembly connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M5-25 (STP1) - A42-3 (L) Always Below 1 Ω
M5-25 (STP1) or A42-3 (L) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

OK

15.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

15.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the A19 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A19-9 (STAR) - C52-4 (B) Always Below 1 Ω
A19-9 (STAR) or C52-4 (B) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK STEERING LOCK FUNCTION
a.

Check that the steering unlocks when the ignition switch is turned to ACC.

OK:

The steering unlocks.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

17.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B557052C06
1.458,0.073 1.875,0.323 0.417,0.25 1.385,1.802 1.604,1.802 1.604,1.802 1.604,0.969 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.552,0.104 1.865,0.302 0.313,0.198 10 false A19 0.99,1.719 1.917,1.917 0.927,0.198 10 false STAR
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A19-9 (STAR) - Body ground Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1.0 V or less


HINT:

*: While the engine is cranking, the auxiliary battery voltage may drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

18.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the A19 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the C52 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A19-9 (STAR) - C52-4 (B) Always Below 1 Ω
A19-9 (STAR) or C52-4 (B) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

19.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Install the ST relay to the No. 1 engine room relay block and No. 1 junction block assembly.


b.
B557052C07
1.458,0.073 1.875,0.323 0.417,0.25 1.063,1.927 1.302,1.927 1.302,1.927 1.302,1.094 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.552,0.104 1.865,0.302 0.313,0.198 10 false A19 0.771,1.833 1.083,2.031 0.313,0.198 10 false STA
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A19-20 (STA) - Body ground Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1.0 V or less


HINT:

*: While the engine is cranking, the auxiliary battery voltage may drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

20.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)
a.

Disconnect the A19 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A19-20 (STA) - 2 (ST relay) Always Below 1 Ω
A19-20 (STA) or 2 (ST relay) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

21.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C52-9 (L) - 2 (ST relay) Always Below 1 Ω
C52-9 (L) or 2 (ST relay) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR