The reaction force pressure sensor detects and outputs the brake fluid pressure of the stroke simulator, which changes in accordance with brake pedal operation, to the No. 1 skid control ECU (brake booster with master cylinder assembly).
Brake pressure sensor "D": Reaction force pressure sensor
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| C057728 | Brake Pressure Sensor "D" Signal Bias Level Out of Range / Zero Adjustment Failure | When the brake pedal is not depressed, the reaction force pressure sensor output value is -0.63 MPa (-6.4 kgf/cm2, -91.4 psi) or less or 1.53 MPa (15.6 kgf/cm2, 222 psi) or more for 3 seconds or more. | No. 1 skid control ECU (brake booster with master cylinder assembly) | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".
Check that the brake pedal and the brake pedal stroke sensor assembly are properly installed and that the pedal can be depressed normally.
Check and adjust the brake pedal height.
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for HV Model LHD)>ADJUSTMENT
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for HV Model RHD)>ADJUSTMENT
Adjust the brake pedal stroke sensor assembly.
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL STROKE SENSOR (for LHD)>INSTALLATION
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL STROKE SENSOR (for RHD)>INSTALLATION
| Proceed to |
|---|
| NEXT |
NEXT
Check that the reaction force pressure sensor output value is within 0.00 to 1.53 MPa when the brake pedal is not depressed.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Reaction Force Pressure | Pressure value of stroke simulator | Min.: 0.00 MPa
Max.: 24.48 MPa |
Brake pedal released: 0.00 to 1.53 MPa | Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal |
| Tester Display |
|---|
| Reaction Force Pressure |
The reaction force pressure sensor output value is within 0.00 to 1.53 MPa.
If the reaction force pressure sensor output value is within 0.00 to 1.53 MPa, the No. 1 skid control ECU (brake booster with master cylinder assembly) automatically performs zero point calibration every time the ignition switch is turned to ON.
Therefore, if the reaction force pressure sensor output value is not within 0.00 to 1.53 MPa, replace the No. 1 skid control ECU (brake booster with master cylinder assembly) with a new one.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for HV Model LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for HV Model RHD)>REMOVAL
Clear the DTCs.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Check if the same DTC is output.
Even if the DTC is cleared, it will immediately be output again if the reaction force pressure sensor zero point malfunction remains.
| Result | Proceed to |
|---|---|
| DTC C057728 is not output. | A |
| DTC C057728 is output. | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for HV Model LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for HV Model RHD)>REMOVAL