Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR › from 2020.11
RM37A0E _59 Vehicle Exterior _086885 DOOR / HATCH _0418601 BACK DOOR A

DOOR / HATCH  BACK DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during back door removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

Rear television camera assembly*
w/ Parking Assist Monitor System:
·

Parking assist monitor system initialization

·

Television camera assembly optical axis (Back camera position setting)


Parking Assist Monitor System (Click here)
w/ Panoramic View Monitor System:

Rear television camera view adjustment


Panoramic View Monitor System (Click here)
Replacement or removal and installation of 2 or more parts:
·

Front television camera assembly, radiator grille sub-assembly or front bumper assembly

·

Rear television camera assembly

·

Side television camera assembly LH or outer rear view mirror assembly LH

·

Side television camera assembly RH or outer rear view mirror assembly RH


w/ Panoramic View Monitor System:

Television camera view adjustment


Panoramic View Monitor System (Click here)
Multiplex network door ECU* Reset back door close position Power Back Door System (Click here)

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

Rear television camera assembly*
w/ Parking Assist Monitor System:
·

Parking assist monitor system initialization

·

Television camera assembly optical axis (Back camera position setting)


Parking Assist Monitor System (Click here)
w/ Panoramic View Monitor System:

Rear television camera view adjustment


Panoramic View Monitor System (Click here)
Replacement or removal and installation of 2 or more parts:
·

Front television camera assembly, radiator grille sub-assembly or front bumper assembly

·

Rear television camera assembly

·

Side television camera assembly LH or outer rear view mirror assembly LH

·

Side television camera assembly RH or outer rear view mirror assembly RH


w/ Panoramic View Monitor System:

Television camera view adjustment


Panoramic View Monitor System (Click here)
Multiplex network door ECU* Reset back door close position Power Back Door System (Click here)

PROCEDURE

Hide 64783F 1.REMOVE DECK TRIM POCKET COVER PLATE

a.
B563620C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 4 clips as shown in the illustration.


b.
B563622C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 guides to remove the deck trim pocket cover plate as shown in the illustration.


Hide 81570 2.REMOVE CENTER STOP LIGHT ASSEMBLY

Hide 81572 3.REMOVE CENTER STOP LIGHT GASKET

Hide 81574 4.REMOVE CENTER STOP LIGHT COVER

Hide 67848E 5.REMOVE BACK DOOR SERVICE HOLE COVER LH

a.
B563624C01
2.219,0.99 2.635,0.573 true 2.635,0.469 2.813,0.656 0.177,0.188 10 true *a
*a Protective Tape
V113146

Place Screwdriver Here
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws and 2 guides to remove the back door service hole cover LH as shown in the illustration.


Hide 67847 6.REMOVE BACK DOOR SERVICE HOLE COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 64780A 7.REMOVE BACK DOOR TRIM PANEL ASSEMBLY

a.
B563626C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the 6 clips as shown in the illustration.


b.
B563627C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the 6 clips as shown in the illustration.


c.
B563628C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Disengage the 2 clips and 2 guides to remove the back door trim panel assembly as shown in the illustration.


Hide 74811D 8.REMOVE DOOR PULL HANDLE

a.
B563630C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 7 claws to remove the door pull handle as shown in the illustration.


b.

w/ Power Back Door:

i.

Disconnect the connector.



Hide 85292A 9.REMOVE REAR WIPER ARM HEAD CAP

Hide 10.REMOVE REAR WIPER ARM AND BLADE ASSEMBLY

Hide 85110R 11.REMOVE REAR WIPER MOTOR ASSEMBLY

Hide 85143R 12.REMOVE REAR WIPER MOTOR GROMMET

Hide 86160Z 13.REMOVE REAR NO. 3 SPEAKER ASSEMBLY (for 11 Speakers)

Hide 76832A 14.REMOVE BACK DOOR FINISH PANEL COVER LH

a.
B563632C01
0.583,1.25 0.938,0.823 true 0.5,1.25 0.729,1.438 0.229,0.188 10 true *a
*a Protective Tape
V113147

Remove in this Direction


Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws and guide to remove the back door finish panel cover LH as shown in the illustration.


Hide 76831A 15.REMOVE BACK DOOR FINISH PANEL COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 84840G 16.REMOVE BACK DOOR OPENER SWITCH ASSEMBLY

Hide 76835A 17.REMOVE NO. 1 BACK DOOR FINISH PANEL PROTECTOR

a.
B563634C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and 2 guides to remove the No. 1 back door finish panel protector as shown in the illustration.


Hide 81270 18.REMOVE LICENSE PLATE LIGHT ASSEMBLY

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>LIGHTING (EXT)>LICENSE PLATE LIGHT ASSEMBLY>REMOVAL


Hide 69350P 19.REMOVE BACK DOOR LOCK ASSEMBLY (w/o Power Back Door)

Hide 69350P 20.REMOVE BACK DOOR LOCK ASSEMBLY WITH COURTESY LIGHT SWITCH (w/ Power Back Door)

Hide 84280D 21.REMOVE POWER BACK DOOR SENSOR ASSEMBLY LH (w/ Power Back Door)

Hide 84270G 22.REMOVE POWER BACK DOOR SENSOR ASSEMBLY RH (w/ Power Back Door)

HINT:

Use the same procedure as for the LH side.


Hide 81590A 23.REMOVE REAR LIGHT ASSEMBLY LH

Hide 81580D 24.REMOVE REAR LIGHT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 89222A 25.REMOVE MULTIPLEX NETWORK DOOR ECU (w/ Power Back Door)

Hide 67282F 26.REMOVE BACK DOOR LOWER STOPPER LH

a.
B563635

Remove the 2 bolts.


b.

Disengage the guide to remove the back door lower stopper LH.


Hide 67281B 27.REMOVE BACK DOOR LOWER STOPPER RH

HINT:

Use the same procedure as for the LH side.


Hide 28.REMOVE CUSHION

a.
B563636

Disengage the 2 claws to remove the cushion.

HINT:

Use the same procedure for the RH side and LH side.



Hide 29.REMOVE TELEVISION CAMERA ASSEMBLY WITH NOZZLE (w/o Digital Inner Mirror)

Hide 30.REMOVE TELEVISION CAMERA ASSEMBLY WITH NOZZLE (w/ Digital Inner Mirror)

Hide 82184 31.REMOVE NO. 1 BACK DOOR WIRE

a.
B563637C01
2.073,1.375 2.323,1.583 0.25,0.208 12 true *A
*A w/ Digital Inner Mirror


Disconnect each connector.


b.

Disengage the 2 clamps.


c.
B563638C01
0.844,0.542 1.115,0.26 true 2.604,0.458 2.323,0.198 true 0.542,0.927 0.396,0.354 0.396,0.354 0.698,0.635 true 3.063,0.708 3.208,0.417 3.208,0.417 3.146,0.938 true 3.208,0.281 3.427,0.49 0.219,0.208 12 true *A 0.156,0.198 0.396,0.396 0.24,0.198 12 true *A 0,0.51 0.24,0.708 0.24,0.198 12 true *A 3.188,1.417 3.427,1.615 0.24,0.198 12 true *A 1.125,0.146 1.365,0.344 0.24,0.198 12 true *A 2.042,0.083 2.281,0.281 0.24,0.198 12 true *A
*A w/ Power Back Door


Disconnect each connector.


d.

Disengage each clamp.


e.

Secure the rope with a diameter of 9.0 mm (0.354 in.) to the No. 1 back door wire with nonwoven tape as shown in the illustration.

B563639C01
1.5,2.833 1.5,2 true 6.167,1.417 6.167,1.135 false 5.417,2.615 6.25,2.333 6.25,2.333 6.063,2.875 false 5.573,3.51 3.833,3.5 3.833,3.5 3.948,3.333 false 4.76,3.802 4.5,3.802 false 6.583,3.917 6.667,3.417 true 1.417,2.865 1.729,3.021 0.313,0.156 10 false *a 6.083,1.448 6.396,1.604 0.313,0.156 10 false *b 3.656,3.417 3.969,3.573 0.313,0.156 10 false *c 6.281,2.229 6.594,2.385 0.313,0.156 10 false *d 4.323,3.719 4.635,3.875 0.313,0.156 10 false *d 6.396,3.917 6.719,4.167 0.323,0.25 12 false *A 6.604,3.927 6.917,4.083 0.313,0.156 10 false *d
*A w/ Digital Inner Mirror - -
*a Nonwoven Tape *b Rope
*c Clamp *d Connector


NOTICE:
·

As conduction performance may degrade if adhesive from the nonwoven tape contacts the connecting parts of the connectors, cover the connectors with a plastic bag or similar before applying the nonwoven tape.

·

Make sure that the rope is secured with nonwoven tape to prevent the rope from separating from the No. 1 back door wire when removing it.



HINT:
·

As the No. 1 back door wire is likely to be caught in the narrow areas inside the back door panel sub-assembly, make sure to align the clamp and connectors in a straight line and cover the edges of the connectors with nonwoven tape.

·

A rope with a diameter of 8.0 mm (0.315 in.) or less may be caught in the gaps on the inside of the back door panel sub-assembly. Make sure to use a rope with a diameter of 9.0 mm (0.354 in.).




f.

Remove the No. 1 back door wire as shown in the illustration.

B563641C01
0,0 0,0 false
V113147

Remove in this Direction - -


NOTICE:
·

The rope will be used when installing the No. 1 back door wire. Leave the rope inside the back door panel sub-assembly.

·

This step should not be performed with the back door panel sub-assembly removed from the vehicle.




Hide 85345R 32.REMOVE REAR WASHER NOZZLE

Hide 85373R 33.REMOVE REAR WASHER (FROM JOINT TO NOZZLE) HOSE

a.
B563644

Disconnect the No. 1 camera cleaner hose to remove the rear washer (from joint to nozzle) hose.


Hide 867F2 34.REMOVE NO. 2 CAMERA CLEANER HOSE

a.
B563645

Disengage the clamp.


b.

Disconnect the No. 1 camera cleaner hose to remove the No. 2 camera cleaner hose.


Hide 35.REMOVE NO. 1 CAMERA CLEANER HOSE

a.
B563646

Disengage the clamp.


b.

Disconnect the washer hose.


c.
B563647

Disengage the clamp.


d.

Secure the rope with a diameter of 9.0 mm (0.354 in.) to the No. 1 camera cleaner hose with nonwoven tape as shown in the illustration.

B563648C01
5.25,3.25 5.25,1.667 true 0.458,0.719 0.458,0.917 false 1.917,1.833 1.917,1.625 false 2.927,1.917 2.927,1.75 false 5.177,3.271 5.438,3.469 0.26,0.198 10 false *a 0.375,0.938 0.688,1.094 0.313,0.156 10 false *b 2.854,1.938 3.167,2.094 0.313,0.156 10 false *c 1.844,1.854 2.156,2.01 0.313,0.156 10 false *d
*a Nonwoven Tape *b Rope
*c Clamp *d Washer Hose


NOTICE:

Make sure that the rope is secured with nonwoven tape to prevent the rope from separating from the No. 1 camera cleaner hose when removing it.


HINT:
·

As the No. 1 camera cleaner hose is likely to be caught in the narrow areas inside the back door panel sub-assembly, make sure to align the clamp and washer hose in a straight line and cover the edges of the washer hose with nonwoven tape.

·

A rope with a diameter of 8.0 mm (0.315 in.) or less may be caught in the gaps on the inside of the back door panel sub-assembly. Make sure to use a rope with a diameter of 9.0 mm (0.354 in.).




e.

Remove the No. 1 camera cleaner hose as shown in the illustration.

B563650C01
0,0 0,0 false
V113147

Remove in this Direction - -


NOTICE:
·

The rope will be used when installing the No. 1 camera cleaner hose. Leave the rope inside the back door panel sub-assembly.

·

This step should not be performed with the back door panel sub-assembly removed from the vehicle.




Hide 68960 36.REMOVE BACK DOOR STAY ASSEMBLY LH (w/o Power Back Door)

Hide 68950C 37.REMOVE BACK DOOR STAY ASSEMBLY RH (w/o Power Back Door)

HINT:

Use the same procedure as for the LH side.


Hide 68920 38.REMOVE POWER BACK DOOR UNIT SET ASSEMBLY LH (w/ Power Back Door)

Hide 68910A 39.REMOVE POWER BACK DOOR UNIT SET ASSEMBLY RH (w/ Power Back Door)

HINT:

Use the same procedure as for the LH side.


Hide 68948 40.REMOVE BACK DOOR DAMPER STAY LOWER BRACKET LH

Hide 68947 41.REMOVE BACK DOOR DAMPER STAY LOWER BRACKET RH

HINT:

Use the same procedure as for the LH side.