When removing or installing the rear disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.
While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
48759
1.INSTALL LOWER CONTROL ARM PIN
Secure the rear axle carrier sub-assembly in a vise using aluminum plates.
Do not overtighten the vise.
Using SST, install a new lower control arm pin to the rear axle carrier sub-assembly as shown in the illustration.
42305
2.TEMPORARILY INSTALL REAR AXLE CARRIER SUB-ASSEMBLY
Secure the rear axle carrier sub-assembly in a vise using aluminum plates.
Do not overtighten the vise.
Using a brass bar and a hammer, push out the bushing until it is positioned as shown in the illustration.
Pushing out the bushing makes it easier to install the rear axle carrier sub-assembly.
Temporarily install the rear axle carrier sub-assembly to the rear No. 1 suspension arm assembly with the spacer and nut (A).
Fully tighten the nut (A) after stabilizing the suspension.
Temporarily install the rear axle carrier sub-assembly to the rear No. 2 suspension arm assembly with the bolt (B) and nut.
Insert the bolt with the threaded end facing the front of the vehicle.
Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.
Fully tighten the bolt (B) after stabilizing the suspension.
Temporarily install the rear axle carrier sub-assembly to the rear upper control arm assembly with the bolt (C) and nut.
Insert the bolt with the threaded end facing the rear of the vehicle.
Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.
Fully tighten the bolt (C) after stabilizing the suspension.
Install the rear axle carrier sub-assembly to the rear lower shock absorber bracket sub-assembly with the 2 bolts (D).
Slowly lower the rear No. 2 suspension arm assembly.
48780E
3.INSTALL REAR TRAILING ARM ASSEMBLY
42450B
4.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY
42431
5.INSTALL REAR DISC
6.INSTALL REAR DISC BRAKE CYLINDER MOUNTING WITH BRAKE PAD
47850
7.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY
89544E
8.INSTALL REAR SKID CONTROL SENSOR
890C0A
9.INSTALL NO. 2 PARKING BRAKE WIRE ASSEMBLY
Install the No. 2 parking brake wire assembly to the rear trailing arm assembly with the 3 bolts.
Install the No. 2 parking brake wire assembly to the rear axle carrier sub-assembly with the bolt.
Connect the No. 2 parking brake wire assembly connector to the rear skid control sensor.
Connect the No. 2 parking brake wire assembly connector to the parking brake actuator assembly.
47319F
10.INSTALL REAR FLEXIBLE HOSE
Install the rear flexible hose to the rear upper control arm assembly with the bolt.
42312B
11.INSTALL REAR AXLE SHAFT NUT
Clean the threaded parts on the rear drive shaft assembly and a new rear axle shaft nut using non-residue solvent.
Be sure to perform this work even when using a new rear drive shaft assembly.
Keep the threaded parts free of oil and foreign matter.
Using a 30 mm deep socket wrench, temporarily install the rear axle shaft nut.
Keep depressing the brake pedal to prevent the rear drive shaft assembly from rotating.
Using a chisel and hammer, stake the rear axle shaft nut.
12.STABILIZE SUSPENSION
48790
13.INSTALL REAR UPPER CONTROL ARM ASSEMBLY
Install the rear upper control arm assembly to the rear axle carrier sub-assembly with the bolt.
Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.
48720A
14.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY
Install the rear No. 1 suspension arm assembly with the nut.
48740F
15.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY
Install the rear No. 2 suspension arm assembly (rear axle carrier sub-assembly side) with the bolt.
Click hereSuspension>REAR SUSPENSION>REAR LOWER ARM>INSTALLATION
48738
16.INSTALL REAR SUSPENSION ARM COVER
17.INSTALL REAR WHEEL
18.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (for HV Model)
Connect the reservoir level switch connector.
for LHD:
Install the brake master cylinder reservoir assembly to the reservoir bracket with the bolt and nut.
Engage the clamp to install the wire harness to the brake master cylinder reservoir assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>INSTALLATION
Turn the ignition switch to ON (READY).
Depress the brake pedal and release it.
19.INSPECT AND ADJUST REAR WHEEL ALIGNMENT
20.CHECK FOR SPEED SENSOR SIGNAL