Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING UNIT (for Manual Air Conditioning System)

AIR CONDITIONING UNIT (for Manual Air Conditioning System) > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.



1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start up the engine.

  1. Turn the A/C switch ON.

  1. Operate the cooler compressor with an engine speed of approximately 1,000 rpm for 5 to 6 minutes to circulate the refrigerant and collect the compressor oil remaining in each component into the cooler compressor.

  1. Stop the engine.

  1. Using SST, discharge the refrigerant gas.

    SST
    09985-20010   (09985-02130, 09985-02150, 09985-02090, 09985-02110, 09985-02010, 09985-02050, 09985-02060, 09985-02070)



2. DRAIN ENGINE COOLANT
  1. for 2TR-FE:

  1. for 1KD-FTV:

  1. for 2KD-FTV:

  1. for 5L-E:



3. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



5. DISCONNECT SUCTION HOSE SUB-ASSEMBLY


    E173197
  1. Remove the bolt and disconnect the suction hose sub-assembly.

    NOTICE:
    E173198E02
    1. Do not use a screwdriver or similar tool to disconnect the suction hose sub-assembly.
    1. Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering.

    Text in Illustration 
    *a
    Disconnect tube by hand

  1. Remove the O-ring from the suction hose sub-assembly.



6. DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY
  1. Disconnect the air conditioning tube and accessory assembly.

    NOTICE:
    1. Do not use a screwdriver or similar tool to disconnect the air conditioning tube and accessory assembly.
    2. Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering.

  1. Remove the O-ring from the air conditioning tube and accessory assembly.



7. DISCONNECT HEATER WATER INLET HOSE


E225468
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water inlet hose.

    HINT:
    Collect the engine coolant in a container.



8. DISCONNECT HEATER WATER OUTLET HOSE


E225469
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water outlet hose.

    HINT:
    Collect the engine coolant in a container.



9. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY
(Click here)


10. REMOVE NO. 2 HEATER TO REGISTER DUCT


E225181
  1. Remove the 3 clips and No. 2 heater to register duct.



11. REMOVE NO. 1 HEATER TO REGISTER DUCT


E225182
  1. Remove the clip.

  1. Detach the 3 claws and remove the No. 1 heater to register duct.



12. REMOVE NO. 3 HEATER TO REGISTER DUCT


E225183
  1. Remove the clip.

  1. Detach the 4 claws and remove the No. 3 heater to register duct.



13. REMOVE DEFROSTER NOZZLE ASSEMBLY


E225184
  1. Using a screwdriver, detach the 4 clips and remove the defroster nozzle assembly.



14. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
(Click here)


15. REMOVE STEERING COLUMN ASSEMBLY
(Click here)


16. REMOVE NO. 1 AIR DUCT


E226311
  1. Detach the 2 claws and remove the No. 1 air duct.



17. REMOVE NO. 2 AIR DUCT


E226312
  1. Detach the 2 claws and remove the No. 2 air duct.



18. REMOVE NO. 4 AIR DUCT


E226313
  1. Detach the 2 claws and remove the No. 4 air duct.



19. REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY


E225185E01
  1. Detach the 2 clamps and remove the 2 nuts labeled A.

  1. Disconnect the connectors and remove the driver side junction block.

  1. Remove the screw.

  1. Remove the bolt, nut labeled B and No. 1 instrument panel brace sub-assembly.
    Text in Illustration 
    *1
    Screw
    *2
    Nut A
    *3
    Nut B
    *4
    Bolt



20. REMOVE ECM
  1. for 2TR-FE:
    (Click here)

  1. for 1KD-FTV:
    (Click here)

  1. for 2KD-FTV:
    (Click here)

  1. for 5L-E:
    (Click here)



21. REMOVE INSTRUMENT PANEL REINFORCEMENT


E225186
  1. Disconnect the connector and detach the 3 clamps.



    E225187
  1. Detach the 2 clamps and disconnect the 2 connectors.



    E225188
  1. Remove the 2 bolts and disconnect the ground wires from the instrument panel reinforcement.



    E225885
  1. Remove the grommet from the vehicle body.



  1. Detach the 12 clamps.


    E225189

  1. Disconnect the connectors.



  1. Remove the 3 bolts.


    E225190



  1. for LHD:



    1. Remove the 8 bolts and instrument panel reinforcement.


      E225191



  1. for RHD:

    1. for Automatic Transmission:
      Remove the 7 bolts and instrument panel reinforcement.



    2. for Manual Transmission:
      Remove the 8 bolts and instrument panel reinforcement.


      E235784E01


      Text in Illustration 
      *A
      for Manual Transmission
      -
      -



22. REMOVE NO. 1 COOLER UNIT DRAIN HOSE


E225884
  1. Remove the No. 1 cooler unit drain hose.



23. REMOVE AIR CONDITIONING UNIT ASSEMBLY


E225192
  1. Remove the bolt, nut and air conditioning unit assembly.



24. REMOVE NO. 3 AIR DUCT


E226397
  1. Detach the 2 claws and remove the No. 3 air duct.