Lack of Power or Hesitation
Circuit diagnosis · Vehicles built Jun 2011 – Jul 2012
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
| Malfunction Condition |
Main Trouble Area |
Related Trouble Area |
|
(a) Injector malfunctions
|
|
- HINT:
- Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors causing the malfunction.
- Check that the vehicle has not been modified in any way prior to the vehicle inspection.
- This troubleshooting procedure checks for the cause of an obvious lack of engine power while the vehicle is being driven (such as the maximum speed being extremely low).
- Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors causing the malfunction.
| Faults and Symptoms of Common Rail Diesel Components |
Engine Control
Mass Air Flow Meter Main fault
Decrease in performance (foreign matter is stuck)
Symptoms
Lack of power, black smoke
Data List
MAF
- HINT:
- The maximum fuel injection volume is controlled according to the output from the mass air flow meter.
Intake System Symptom: Main fault
- Lack of power (no black smoke): air filter blockage, air duct is crushed/leaking
- Black smoke (no lack of power): Leakage between the turbo and intake manifold
Data List
- MAP (inside intake air pressure)
- Target Booster Pressure
When the accelerator is fully depressed, if MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds then a lack of power will be felt.
- MAF
Turbocharger System Main fault
- Air leak in the turbocharged air passage
- Turbocharger (turbine, bearing, variable nozzle)
Symptoms
Lack of power (when vehicle starting, when heavy load)
(Black smoke is not emitted when racing while vehicle stopped)
Data List
MAP (inside intake air pressure), Target Booster Pressure - When the accelerator is fully depressed, if MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds then a lack of power will be felt.
- With the ignition switch ON or during idling, MAP = atmospheric pressure (standard atmospheric pressure = 101 kPa). When the engine speed is about 1500 rpm or more, the turbocharger starts to take effect and MAP becomes higher than atmospheric pressure.
- Atmospheric pressure decreases 1 kPa each time altitude increases by 100 m, and is also affected by the current weather conditions.
Exhaust System Main fault
Blockage
Symptoms
Lack of power (high engine speed, when heavy load)
Data List
MAP (inside intake air pressure), Target Booster Pressure
When the accelerator is fully depressed, if MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds then a lack of power will be felt.
Glow System Main fault
Open circuit, glow plug relay fault
Symptoms
Difficult to start, rough idle, knocking, white smoke (when cold)
Data List
Check the glow plug indicator light
Diagnostic Point
Try to measure the resistance of the glow plug
Engine - 1 Main fault
Damaged, seized up
Symptoms
Cannot crank, crank speed is low, strange noise
Engine - 2 Main fault
Loss of compression
Data List
Engine Speed of Cyl# - When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression.
- If Injection Feedback Val is more than 3 mm3/st, the cylinder may have a fault.
Diesel Injection
Fuel Supply Pump Main fault
-
Symptoms
Difficult to start, engine stalling, rough idle, lack of power
Data List
Fuel Press, Target Common Rail Pressure, Target Pump SCV Current - At a stable condition (e.g. Idling), Fuel Press is within +/-5000 kPa of "Target Common Rail Pressure".
- If the fuel pressure is 20000 kPa below the target pressure then a lack of power will be felt.
- If the fuel pressure is below 25000 kPa then idling will be rough.
- If Target Pump SCV Current is 3000 mA or more, the suction control valve may be stuck.
- HINT:
- The fuel pressure changes at engine starting, but is approx. 25000 kPa at engine start after the engine is warmed up.
- When Target Pump SCV Current is 3000 mA or more, the suction control valve has a tendency to become stuck.
- The fuel pressure changes at engine starting, but is approx. 25000 kPa at engine start after the engine is warmed up.
Diagnostic Trouble Code
Even if Fuel Press is less than Target Common Rail Pressure, a DTC will not be stored.
Fuel Filter Main fault
Blockage
Symptoms
Difficult to start, engine stalling, rough idle, lack of power
Data List
Fuel Press, Target Common Rail Pressure - At a stable condition (e.g. Idling), the fuel pressure is within +/-5000 kPa of "Target Common Rail Pressure".
- If the fuel pressure is 20000 kPa below the target pressure then a lack of power will be felt.
- If the fuel pressure is below 25000 kPa then idling will be rough.
- HINT:
- The fuel pressure changes at engine starting, but is approx. 25000 kPa at engine start after the engine is warmed up.
Diagnostic Trouble Code
Even if Fuel Press is less than Target Common Rail Pressure, a DTC will not be stored.
Fuel Injector Main fault
Blockage
Symptoms
Rough idle, lack of power, black smoke, white smoke, knocking
Data List
Injection Feedback Val - When an Injection Feedback Val is more than 3 mm3/st, the cylinder is not normal. This can be read after idling for 1 minute with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)).
Injector Driver (EDU) Main fault
Circuit fault: The fuel injector does not open.
Symptoms
Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking
Data List
Same as fuel injector
Diagnostic Trouble Code
When the EDU has a fault, some DTCs may be stored.
Fuel Pressure Sensor Main fault
Open circuit, decrease in performance (foreign matter is stuck)
Symptoms
Difficult to start, rough idle, engine stall, lack of power
Data List
Fuel Press, Target Common Rail Pressure - At a stable condition (e.g. Idling), Fuel Press is within +/-5000 kPa of "Target Common Rail Pressure".
Diagnostic Code
When the fuel pressure sensor has a fault, some DTCs may be stored.
Irregular Fuel Main fault
-
Symptoms
Difficult to start, rough idle (especially when cold)
- At a stable condition (e.g. Idling), Fuel Press is within +/-5000 kPa of "Target Common Rail Pressure".
Diesel EGR
EGR System Main fault
- Does not move smoothly
- Does not close fully
Symptoms
- Rough Idle
- EGR valve stuck closed: A loud turbocharger sound.
- EGR valve stuck open: Difficult to start (does not stall), black smoke, lack of power, jerking (If there is an excess in the quantity of EGR and there is a heavy load, when the vehicle starts moving, a lack of power will be felt. Also, when racing the engine, there will be some black smoke).
Data List
Actual EGR Valve Pos., Target EGR Position - Generally, Actual EGR Valve Pos. = Target EGR Pos. +/-5% (fully closed 0%, fully open 100%).
- Using EGR valve Active Test, check whether Actual EGR Valve Pos. follows Target EGR Position (the engine coolant temperature and intake air temperature should be considered when a malfunction occurs).
- EGR valve is fully closed when the ignition switch is ON (engine stopped).
- EGR valve opens to the halfway point at idling after the engine is warmed up.
- When the EGR valve does not close, MAF (Mass Air Flow) decreases when the vehicle is accelerated at full throttle. MAP also decreases in comparison to Target Booster Pressure, however there is not a large difference.
- When leaving the vehicle idling, when EGR Close Lrn. Status is OK, the normal range of EGR Close Lrn. Val. is 0 to 1 V.
- In cases when EGR Close Lrn. Status. is NG or EGR Close Lrn. Val. is out of the normal range (0 to 1 V), it is possible that the EGR valve cannot completely close.
- Does not move smoothly
Diesel Throttle
Diesel Throttle System Main fault
Stuck, does not move smoothly
Symptoms
- Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed.
- Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur.
Data List
- Actual Throttle Position (fully closed 100%, fully open 0%)
- When the ignition switch is ON (engine stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the ignition switch is turned from ON to off, the throttle is temporarily closed fully.
- Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed.
| Data List Related to Lack of Power |
- Engine Speed
- MAP
- MAF
- Intake Air
- Coolant Temp
- Target Common Rail Pressure
- Fuel Press
- Target Pump SCV Current
- Injection Feedback Val #1 (to #4)
- Injection Volume
- Actual Throttle Position
- Target EGR Position
- Actual EGR Valve Pos.
INSPECTION PROCEDURE
| Explanation of Symptom |
| Lack of Power |
The power of the diesel engine is determined by the quantity of injected fuel and the quantity of intake air. The quantity of injected fuel is determined by the fuel pressure and the amount of time the injector is open for. Basically, the fuel pressure is controlled to reach the target fuel pressure. The throttle valve does not restrict air flow volume, so the manifold absolute pressure is almost the same as atmospheric pressure when idling. At more than approximately 1500 rpm, the turbo starts to operate causing the manifold absolute pressure to become higher than atmospheric pressure. The manifold absolute pressure is controlled to reach the Target Booster Pressure when accelerating the vehicle at full throttle. Also, when accelerating the vehicle at full throttle, the throttle is fully open and the EGR valve is fully closed, preserving the mass air flow. |
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- After replacing the fuel supply pump, the ECM needs initialization (Click here).
- After replacing a fuel injector, the ECM needs registration (Click here).
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
| 1. READ OUTPUT DTC (RELATING TO ENGINE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read pending DTCs.
Result Result
Proceed to
No DTCs are output
A
Engine related DTCs are output
B
|
|
||||
| A | |
| 2. TAKE SNAPSHOT DURING IDLING AND 4000 rpm |
Connect the intelligent tester to the DLC3.

Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
With no load after the engine is warmed up, take a snapshot when idling and at 4000 rpm.
- HINT:
- A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.
- Graphs can be displayed by transferring the stored snapshot data from the tester to a PC. Intelligent Viewer must be installed on the PC.
- The shift lever should be in neutral and the A/C switch and all accessory switches should be off.
- A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.
Data of Normal Vehicle Recorded after Engine Warmed up with A/C OFF while Running Engine at 4000 rpm without Load and while Idling Data List
Reference Values Recorded while Running Engine at 4000 rpm without Load
Reference Values Recorded while Idling
Unit
Vehicle Speed
0
0
km/h
Engine Speed
3997
749
rpm
Accel Position
25.00
0.00
%
Calculate Load
29.4
16.0
%
MAF
110.79
8.12
g/sec.
MAP
143
97
kPa
Target Booster Pressure
170.19
126.52
kPa
Atmosphere Pressure
100
100
kPa
Coolant Temp
83
84
°C
Intake Air
19
16
°C
Fuel Press
90410
30600
kPa
Target Common Rail Pressure
91650
33000
kPa
Target Pump SCV Current
1092.5
997.1
mA
Injection Volume
13.65
5.00
mm3/st
Injection Feedback Val #1
0.3
0.3
mm3/st
Injection Feedback Val #2
-0.4
-0.4
mm3/st
Injection Feedback Val #3
-0.8
-0.8
mm3/st
Injection Feedback Val #4
0.4
0.4
mm3/st
Target Throttle Position
0
86
%
Actual Throttle Position
-1
85
%
Target EGR Position
0.0
39.6
%
Actual EGR Valve Pos.
0.0
40.0
%
VN Turbo Command
62
90
%
- HINT:
- The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc.
- Standard atmospheric pressure is 101 kPa. For every 100 m increase in altitude, pressure drops by 1 kPa. Varies by weather.
| NEXT | |
| 3. TAKE SNAPSHOT DURING LACK OF POWER |
Connect the intelligent tester to the DLC3.

Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
Take a snapshot of the following Data List items with the intelligent tester during lack of power.
- HINT:
- A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.
- Graphs can be displayed by transferring the stored snapshot data from the tester to a PC. Intelligent Viewer must be installed on the PC.
- Move the shift lever to 2nd gear and accelerate the vehicle with the accelerator pedal fully depressed (obey all laws and regulations, and pay attention to traffic conditions while driving the vehicle). Then, check the Data List with the engine warmed up and idling (the shift lever in neutral and the A/C switch and all accessory switches off).
- A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.




- HINT:
- When comparing MAP and Target Booster Pressure, avoid the area where the values are changing (area labeled *1 in the above illustration) and compare the values when they have relatively stabilized.


Reference Values with Engine Speed at 3000 rpm (Point A) Data List
Value
Unit
Vehicle Speed
40
km/h
Engine Speed
3009
rpm
Accel Position
99.60
%
Calculate Load
83.5
%
MAF
165.53
g/sec.
MAP
237
kPa
Target Booster Pressure
235.46
kPa
Atmosphere Pressure
100
kPa
Coolant Temp
83
°C
Intake Air
11
°C
Target Common Rail Pressure
152760
kPa
Target Pump SCV Current
1418.3
mA
Injection Volume
75.76
mm3/st
Injection Feedback Val #1
0.0
mm3/st
Injection Feedback Val #2
-0.7
mm3/st
Injection Feedback Val #3
-0.8
mm3/st
Injection Feedback Val #4
0.9
mm3/st
Target Throttle Position
0
%
Actual Throttle Position
-1
%
Target EGR Position
0.0
%
Actual EGR Valve Pos.
0.0
%
VN Turbo Command
46
%
- HINT:
- Examples of Actual Malfunctions (See "Diagnostic Help" menu)
- Lack of power caused by overly low boost pressure
- Lack of power caused by overly low MAF
- EGR valve stuck in open position
- For engine protection, exhaust gas or fuel economy related reasons, there are some ranges of engine operation where engine power feels like it flattens out, but this is not a malfunction.
- The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc.
Standard atmospheric pressure is 101 kPa. For every 100 m increase in altitude, pressure drops by 1 kPa. Varies by weather.
- The engine speed must be 1500 rpm or less before performing the inspection in which the accelerator pedal is fully depressed and the engine is accelerated to a speed of 3000 rpm.
- Examples of Actual Malfunctions (See "Diagnostic Help" menu)
Check for a lack of power during the driving test.
Result Result
Proceed to
Apparent lack of power is present
A
Apparent lack of power is not present
B
|
|
||||
| A | |
| 4. CHECK SNAPSHOT (MAP AND MAF) |
Check MAP and MAF in the snapshot taken when the engine was running at 4000 rpm with no load.
Result Result
Proceed to
MAP is 117 kPa or more and MAF is 84 g/sec. or more*1
A
MAP is less than 90 kPa*2
B
Except above*3
C
- HINT:
- The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc.
- Standard atmospheric pressure is 101 kPa. For every 100 m increase in altitude, pressure drops by 1 kPa. Varies by weather.
- *1: There may be a problem in the fuel injection system.
- *2: There may be a problem in the turbocharger system.
- *3: There may be a problem in the intake system or a problem with the EGR valve (valve stuck open or valve does not close).
|
|
||||
|
|
||||
| A | |
| 5. CHECK SNAPSHOT (FUEL PRESS, TARGET COMMON RAIL PRESSURE, MAP AND TARGET BOOSTER PRESSURE) |
Check Fuel Press, Target Common Rail Pressure, MAP and Target Booster Pressure in the snapshot taken when the vehicle was accelerating with the accelerator pedal fully depressed in 2nd gear.
Result Result
Proceed to
MAP is less than 205 kPa at an engine speed of 3000 rpm
A
Difference between Fuel Press and Target Common Rail Pressure is +/-20000 kPa or more
B
Except above
C
- HINT:
- The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc.
Standard atmospheric pressure is 101 kPa. For every 100 m increase in altitude, pressure drops by 1 kPa. Varies by weather.
- The engine speed must be 1500 rpm or less before performing the inspection in which the accelerator pedal is fully depressed and the engine is accelerated to a speed of 3000 rpm.
- If the turbocharger movement is not smooth, etc., the value of MAP in the snapshot taken during lack of power will not reach the target value.
When the accelerator pedal is fully depressed and the engine speed is 3000 rpm, the MAP should be more than 205 kPa.
- The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc.
|
|
||||
|
|
||||
| A | |
| 6. CHECK INTAKE SYSTEM |
Check for air leakage and blockage between the air cleaner and turbocharger, and between the turbocharger and intake manifold.
- HINT:
- Check that the intercooler is not clogged with foreign matter.
- Check that there are no disconnected, pinched or leaking hoses or pipes.
- Check that there are no modifications made by the user.
- Check that the intercooler is not clogged with foreign matter.
- OK:
- No leakage or blockage.
|
|
||||
| OK | |
| 7. CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER |
Clean the fuel filter case and replace the fuel filter.
- HINT:
- Be sure to clean the inside of the fuel filter case as the fuel injectors may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.
| NEXT | |
| 8. REPLACE FUEL INJECTORS OF ALL CYLINDERS |
Replace the fuel injectors (Click here).
| NEXT | |
| 9. BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system (Click here).
| NEXT | |
| 10. REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING |
Register the injector compensation code (Click here).
Perform the fuel injector pilot quantity learning (Click here).
| NEXT | |
| 11. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
| NEXT | ||
| ||
| 12. READ VALUE USING INTELLIGENT TESTER (MAP AND ATMOSPHERIC PRESSURE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Atmosphere Pressure.
Compare MAP to Atmosphere Pressure when the ignition switch is ON (do not start the engine).
- Standard:
- Difference between MAP and Atmosphere Pressure is less than 8 kPa.
- HINT:
- If MAP and Atmosphere Pressure have the same value, both are normal. If there is a difference of 8 kPa or more, compare the values to the atmospheric pressure for that day. The sensor whose deviation is the greatest is malfunctioning.
- Standard atmospheric pressure is 101 kPa. For every 100 m increase in altitude, pressure drops by 1 kPa. This varies by weather.
- If MAP and Atmosphere Pressure have the same value, both are normal. If there is a difference of 8 kPa or more, compare the values to the atmospheric pressure for that day. The sensor whose deviation is the greatest is malfunctioning.
Result Result
Proceed to
MAP and Atmosphere Pressure have the same value
A
MAP is different from actual atmospheric pressure
B
Atmosphere Pressure is different from actual atmospheric pressure
C
|
|
||||
|
|
||||
| A | |
| 13. CHECK AIR INTAKE SYSTEM |
Check for air leaks and blockages between the air cleaner case and turbocharger, and between the turbocharger and intake manifold.
Result Result
Proceed to
Leaks and/or blockages exist in the intake system
A
No leaks or blockages in the intake system
B
- HINT:
- Inspect the air intake system, especially hoses and pipes between the air cleaner and turbocharger.
- Check for abnormal disconnections, pipe and hose squashing, and any damage in the intake system.
- Using your hand, check whether the pipes and hoses in the intake system are securely connected.
- When inspecting for a clogged intake system (cause of low MAP), check the following points:
- Clogged air cleaner
- Clogged intake hose
- Diesel throttle valve stuck in closed position
- Check for any modifications in the intake system made by the user.
- Inspect the air intake system, especially hoses and pipes between the air cleaner and turbocharger.
|
|
||||
| A | |
| 14. REPAIR OR REPLACE AIR INTAKE SYSTEM |
Repair or replace the malfunctioning part in the air intake system.
|
|
||||
| 15. REPLACE TURBOCHARGER SUB-ASSEMBLY |
Replace the turbocharger sub-assembly (Click here).
|
|
||||
| 16. REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR |
Replace the manifold absolute pressure sensor.
|
|
||||
| 17. REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 18. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
| NEXT | ||
| ||
| 19. BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system (Click here).
| NEXT | |
| 20. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TEST THE FUEL LEAK) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / Data List / Fuel Press, Target Common Rail Pressure.
Take a snapshot with the intelligent tester during the Active Test.

- HINT:
- Detailed graphs can be displayed by transferring the stored snapshot from the tester to a PC (personal computer) with Intelligent Viewer installed.
Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed.
- HINT:
- In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.


- OK:
- The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.
- HINT:
- "Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.
- "Fuel Press" is the actual fuel pressure.
- "Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.
|
|
||||
| OK | ||
| ||
| 21. CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP |
Disconnect the inlet hose from the fuel supply pump.
Operate the priming pump and check that fuel is being supplied to the fuel supply pump.
- OK:
- Fuel is properly supplied to the fuel supply pump when the priming pump is operated.
- HINT:
- When there is a lack of fuel, the fuel pressure drops.
- Inspect for fuel filter clogging.
- When there is a lack of fuel, the fuel pressure drops.
|
|
||||
| OK | |
| 22. REPLACE FUEL SUPPLY PUMP |
Replace the fuel supply pump (Click here).
|
|
||||
| 23. REPAIR OR REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP) |
Check and repair or replace the clogged fuel pipe.
| NEXT | |
| 24. BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system (Click here).
| NEXT | |
| 25. PERFORM FUEL SUPPLY PUMP INITIALIZATION |
Perform fuel supply pump initialization (Click here).
| NEXT | |
| 26. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / Data List / Fuel Press, Target Common Rail Pressure.
Take a snapshot with the intelligent tester during the Active Test.

- HINT:
- Detailed graphs can be displayed by transferring the stored snapshot from the tester to a PC (personal computer) with Intelligent Viewer installed.
Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed.
- HINT:
- In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.


- OK:
- The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.
- HINT:
- "Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.
- "Fuel Press" is the actual fuel pressure.
- "Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.
| NEXT | ||
| ||
| 27. CHECK AIR INTAKE SYSTEM |
Check for air leaks and blockages between the air cleaner case and turbocharger, and between the turbocharger and intake manifold.
Result Result
Proceed to
No leaks or blockages in the intake system
A
Leaks and/or blockages exist in the intake system
B
- HINT:
- Inspect the air intake system, especially hoses and pipes between the air cleaner and turbocharger.
- Check for abnormal disconnections, pipe and hose squashing, and any damage in the intake system.
- Using your hand, check whether the pipes and hoses in the intake system are securely connected.
- By applying soapy water and revving up the engine, air leaks from the intake system can be checked by checking for bubbles.
- Make sure that the hose between the manifold absolute pressure sensor and intake manifold is not loose or disconnected.
- Check for any modifications in the intake system made by the user.
- Inspect the air intake system, especially hoses and pipes between the air cleaner and turbocharger.
|
|
||||
| A | |
| 28. INSPECT TURBOCHARGER SUB-ASSEMBLY |
Inspect the turbocharger sub-assembly (Click here).
|
|
||||
| OK | |
| 29. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EGR CUT) |
Connect the intelligent tester to the DLC3.
Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.
Turn the ignition switch off. Wait for 30 seconds, and then restart the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
Read the MAF value displayed on the tester while the engine is idling.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the EGR Valve Close.
Read the MAF value when the EGR valve is closed using the Active Test function.
- HINT:
- If idling continues for 15 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or to restart the engine.
- Before performing the diagnosis, confirm that the EGR valve target opening angle is not 0%.
- When "Coolant Temp" is 75°C (167°F) or higher during idling, the exhaust gas flows through the EGR cooler. If MAF does not change when the EGR is cut even though the EGR valve is operating normally, the EGR cooler may be clogged.
- When idling while warming up the engine, the actuator operates and the EGR cooler is bypassed. However, if the connector of the VSV for the EGR cooler is disconnected, the EGR cooler is not bypassed and it is possible to check how clogged the EGR cooler is.
- If idling continues for 15 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or to restart the engine.
Result Active Test
Result
Proceed to
Activate the EGR Valve Close:
Off (Open) to On (Closed)
MAF value does not change
A
MAF value changes
B
- NOTICE:
- As the measured values may differ from those shown below due to factors such as differences in measuring environments and changes in vehicle condition due to aging, do not use these values to determine whether the vehicle is malfunctioning or not.
- HINT:
- The problem may be a temporary one, due to the entry of deposits or foreign matter. Check that there are no deposits or foreign matter in the electric vacuum regulating valve assembly or mass air flow meter.
- Reference:
EGR Valve Condition (Opening)
Measuring Condition
MAF (Reference)
Open (55%)
- Atmosphere pressure: 101 kPa
- Intake air temperature: 30°C (86°F)
- Engine coolant temperature: 88°C (190°F)
3.0 to 9.0 gm/s
Closed (0%)
15 to 22 gm/s
- Atmosphere pressure: 101 kPa
|
|
||||
| A | |
| 30. READ VALUE USING INTELLIGENT TESTER (MAF) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
Read the value.
- Standard:
Tester Display
Condition
Specified Condition
MAF
Engine not running
Below 0.3 g/sec
|
|
||||
| OK | |
| 31. REMOVE DEPOSIT (EGR VALVE ASSEMBLY) |
Remove the EGR valve assembly.
Visually check the EGR valve assembly for deposits.If there are deposits, clean the EGR valve assembly.
- HINT:
- If the EGR valve is stuck closed, the intake air amount increases and engine vibration may worsen.
- If the EGR valve does not operate due to clogging or disconnection of the vacuum hose, repair the hose.
- If the EGR valve does not close properly or is stuck open, EGR becomes excessive and combustion becomes unstable. Also, there may be a lack of power. In this case, clean the EGR valve.
- When cleaning the EGR valve assembly, use a piece of cloth soaked with non-residue solvent. Spraying the solvent directly onto these parts or soaking the parts in solvent may damage the parts.
- If the EGR valve is stuck closed, the intake air amount increases and engine vibration may worsen.
| NEXT | |
| 32. INSPECT EGR VALVE ASSEMBLY |
Inspect the EGR valve assembly (Click here).
|
|
||||
|
|
||||
| 33. REPLACE EGR VALVE ASSEMBLY |
Replace the EGR valve assembly (Click here).
|
|
||||
| 34. REPAIR OR REPLACE AIR INTAKE SYSTEM |
Repair or replace the malfunctioning part in the air intake system.
|
|
||||
| 35. REPLACE MASS AIR FLOW METER |
Replace the mass air flow meter.
- HINT:
- Before replacing the mass air flow meter, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.
|
|
||||
| 36. REPLACE TURBOCHARGER SUB-ASSEMBLY |
Replace the turbocharger sub-assembly (Click here).
| NEXT | |
| 37. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
| NEXT | ||
| ||
| 38. READ VALUE USING INTELLIGENT TESTER (MAF) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
Read the value.
- Standard:
Tester Display
Condition
Specified Condition
MAF
Engine not running
Below 0.3 g/sec
|
|
||||
| OK | |
| 39. CHECK EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY |
Remove the exhaust manifold converter sub-assembly.
Visually check for catalyst clogging or carbon deposits adhering to the inner wall of the exhaust pipe upstream of the catalyst.
- OK:
- Less than 10% of the cells are clogged.
|
|
||||
|
|
||||
| 40. REPLACE MASS AIR FLOW METER |
Replace the mass air flow meter.
- HINT:
- Before replacing the mass air flow meter, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.
|
|
||||
| 41. REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY |
Replace the exhaust manifold converter sub-assembly.
|
|
||||
| 42. CHECK FOR INTERMITTENT PROBLEMS |
Check for intermittent problems (Click here).
| NEXT | |
| 43. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
| NEXT | ||
| ||
| 44. COMPARE WITH SIMILAR VEHICLE WITH SAME ENGINE |
Confirm the situation in which the lack of power was experienced by the customer again, and compare the driving feeling under the same conditions using a similar vehicle with the same engine while collecting data with the intelligent tester.
- HINT:
- Confirm the state of the following conditions when the lack of power was experienced.
- Accelerator pedal position (vehicle load)
- Vehicle speed
- Engine coolant temperature
- Atmospheric temperature
- Driving conditions before the lack of power occurred
- Climate
- Road and traffic conditions
- When (what day) the problem was noticed
- Whether the problem occurs suddenly or gradually
- How often the problem occurs
- Why the customer felt there is a lack of power (e.g. the customer compared their vehicle with another vehicle, somebody told the customer that their vehicle has a lack of power)
- Level of lack of power (slight or drastic)
Result Result
Proceed to
Significant difference is found
A
Significant difference is not found
B
|
|
||||
| B | |
| 45. EXPLAIN THE INVESTIGATION RESULT TO CUSTOMER |
Vehicle performance is normal.There is no problem at this point in time. However, if the problem recurs, ask the customer to explain in detail the situation in which the problem occurred.The best course may be to have the customer ride in another vehicle with the same specifications to understand that there is no problem with the customer's vehicle.
| NEXT | ||
| ||
