2014 Hilux · Service Manual DRIVE LINE

INSTALLATION

Removal / installation · Vehicles built from Jun 2011


1. INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY
  1. Clean the contact surfaces of the differential carrier and axle housing.

    NOTICE:
    Be careful not to damage the installation surface.

  1. Install the differential carrier, and a new gasket and the washers with the 10 nuts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    Be careful to install the gasket without tearing it.


2. INSTALL REAR AXLE SHAFT WITH BACKING PLATE LH
(Click here)

3. INSTALL REAR AXLE SHAFT WITH BACKING PLATE RH

HINT:
Use the same procedure described described for the LH side.


4. BLEED AIR FROM BRAKE LINE
  1. w/ VSC:
    (Click here)

  1. for TSAM Made:
    (Click here)

  1. for TMT Made:
    (Click here)


5. ADD DIFFERENTIAL OIL

  1. D025304E51
    Add differential oil so that the oil level is within 5 mm (0 to 0.196 in.) from the bottom lip of the differential filler plug hole.
    Text in Illustration 
    *a
    0 to 5 mm (0 to 0.196 in.)

    NOTICE:
    1. After changing the oil seal, drive the vehicle and then check the oil level again.
    2. Too much or too little oil will lead to differential problems.

    HINT:
    If necessary, fill the differential carrier assembly with hypoid gear oil.

    Recommended viscosity:
    Item
    Temperature
    Viscosity
    Front differential (w/ A.D.D.)
    SAE 75W-90
    Front differential (w/o A.D.D.)
    Rear differential
    Above -18°C (0°F)
    SAE 90
    Below -18°C (0°F)
    SAE 80W-90 or SAE 80W

    Differential oil type:
    Item
    Oil type
    Front differential
    Rear differential
    Hypoid gear oil API GL-5 or equivalent
    Rear differential (for LSD)
    Hypoid gear oil LSD API GL-5 or equivalent

    Standard front differential oil capacity:
    Item
    Capacity
    w/o A.D.D.
    1.40 to 1.50 liters (1.48 to 1.58 US qts., 1.23 to 1.32 Imp. qts.)
    w/ A.D.D.
    1.60 to 1.70 liters (1.69 to 1.79 US qts., 1.41 to 1.49 Imp. qts.)

    TMT made Standard rear differential oil capacity:
    Item
    Capacity
    2WD and w/ LSD
    3.15 to 3.25 liters (3.33 to 3.43 US qts., 2.78 to 2.86 Imp. qts.)
    4WD and w/o LSD
    3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.91 to 2.99 Imp. qts.)

    TSAM made :
    Item
    Capacity
    2WD and made for DANA
    2.30 to 2.40 liters (2.43 to 2.54 US qts., 2.02 to 2.11 Imp. qts.)
    4WD, Pre-runner and made for DANA
    (w/o LSD, A.D.D.)
    2.40 to 2.50 liters (2.54 to 2.64 US qts., 2.11 to 2.20 Imp. qts.)
    w/ LSD for 2WD
    3.15 to 3.25 liters (3.33 to 3.43 US qts., 2.78 to 2.86 Imp. qts.)
    w/ LSD for 4WD
    3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.91 to 2.99 Imp. qts.)
    w/ Differential lock
    2.85 to 2.95 liters (3.01 to 3.12 US qts., 2.51 to 2.60 Imp. qts.)

  1. Check for oil leakage when the oil level is low.

  1. for front differential:

    1. A272243E01
      Using SST and the 10 mm straight hexagon wrench, 10 mm union nut wrench and socket adaptor, install a new gasket and the differential filler plug.
      SST
      09961-00950  
      Text in Illustration 
      *1
      10 mm Straight Hexagon Wrench
      *2
      10 mm Union Nut Wrench
      *3
      Socket Adaptor

      Torque:
      39 N*m{ 400 kgf*cm , 29 ft.*lbf }

      NOTICE:
      1. Make sure all the tools are connected in a straight line.
      2. Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.

        Formula:
        T' = T x L3 / (L1 + L2 + L3)
        - T' = Spec. value of torque wrench
        - T = Value of specified tightening torque
        - L1 = Length of union nut wrench
        - L2 = Length of SST
        - L3 = Length of torque wrench

  1. for rear differential:

    1. Install a new gasket and the differential filler plug.

      Torque:
      49 N*m{ 500 kgf*cm , 36 ft.*lbf }


6. INSTALL REAR PROPELLER SHAFT ASSEMBLY
  1. for TSAM Made:
    (Click here)

  1. for TMT Made:
    (Click here)


7. ADJUST PARKING BRAKE
(Click here)

8. INSTALL REAR WHEEL (for 2WD)
  1. Install the wheel.

    Torque:
    152 N*m{ 1,550 kgf*cm , 112 ft.*lbf } for steel wheel
    121 N*m{ 1,234 kgf*cm , 89 ft.*lbf } for aluminum wheel


9. INSTALL REAR WHEEL (for 4WD and Pre-Runner)
  1. Install the wheel.

    Torque:
    105 N*m{ 1,070 kgf*cm , 77 ft.*lbf }


10. CHECK ABS SPEED SENSOR SIGNAL
  1. w/ VSC:
    (Click here )

  1. w/o VSC:
    (Click here)

← REASSEMBLY (from Jun 2011)COMPONENTS (from Jun 2011) →