Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/o Secondary Air Injection System) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052091 SFI SYSTEM(w/o Secondary Air Injection System) C

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/o Secondary Air Injection System)  P0135  Oxygen Sensor Heater Circuit (Bank 1 Sensor 1)  


DESCRIPTION

Refer to DTC P0130 (See page Engine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/o Secondary Air Injection System)>P0130).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0135 Oxygen Sensor Heater Circuit (Bank 1 Sensor 1) Open or short in the heater circuit of the oxygen sensor for 0.5 seconds or more (1 trip detection logic).
·

Open or short in heater circuit of oxygen sensor

·

Heated oxygen sensor

·

ECM


- DTC stored

HINT:

Sensor 1 refers to the sensor closer to the engine assembly.


MONITOR DESCRIPTION

If the output from the heater terminal of the ECM (HT1A) is at a low level when current is not being supplied to the heated oxygen sensor heater, the ECM determines that there is a malfunction. The ECM then illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components Heated oxygen sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Turn the ignition switch to ON and wait for 5 seconds or more.


CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT HEATED OXYGEN SENSOR

OK

2.CHECK TERMINAL VOLTAGE (+B OF HEATED OXYGEN SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (+B OF HEATED OXYGEN SENSOR)
a.
A149595
0.396,1.865 0.75,2.125 0.354,0.26 1.969,1.802 2.354,1.479 true 0.083,0.063 0.333,0.281 0.25,0.219 10 false *a 0.458,1.917 0.844,2.24 0.385,0.323 10 false C78 2.396,1.396 2.781,1.719 0.385,0.323 10 false +B
*a Front view of wire harness connector
(to Heated Oxygen Sensor)


Disconnect the heated oxygen sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C78-2 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

5.INSPECT NO. 1 INTEGRATION RELAY (MAIN)
3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C78-1 (HT1A) - C75-1 (HA1A) Always Below 1 Ω
C78-1 (HT1A) or C75-1 (HA1A) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

e.

Start the engine.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Read the output pending DTCs using the intelligent tester.

Powertrain > Engine > Trouble Codes
50001 61
Result:
Result Proceed to
No pending DTC is output A
Pending DTC P0135 is output B




A

B

5.INSPECT NO. 1 INTEGRATION RELAY (MAIN)
a.

Inspect the No. 1 integration relay (MAIN).

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - NO. 1 INTEGRATION RELAY)

NG

REPLACE NO. 1 INTEGRATION RELAY

6.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - NO. 1 INTEGRATION RELAY)
a.

Disconnect the heated oxygen sensor connector.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C78-2 (+B) - 1J-5 Always Below 1 Ω
C78-2 (+B) or 1J-5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR