Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052110 ECD SYSTEM(for i-ART) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  P2009  Intake Manifold Runner Control Circuit Low (Bank 1)  P2010  Intake Manifold Runner Control Circuit High (Bank 1)  


DESCRIPTION

Refer to DTC P2006 (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>P2006).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2009 Intake Manifold Runner Control Circuit Low (Bank 1) Open in No. 1 vacuum switching valve (for swirl control valve) circuit for 0.5 seconds (2 trip detection logic).
·

No. 1 vacuum switching valve (for swirl control valve)

·

Open in No. 1 vacuum switching valve (for swirl control valve) circuit

·

ECM


Comes on DTC stored
P2010 Intake Manifold Runner Control Circuit High (Bank 1) Short in No. 1 vacuum switching valve (for swirl control valve) circuit for 0.5 seconds (2 trip detection logic).
·

No. 1 vacuum switching valve (for swirl control valve)

·

Short in No. 1 vacuum switching valve (for swirl control valve) circuit

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

P2009, P2010
DTC Detection Drive Pattern 2 seconds after engine is started, race engine for 1 second

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE)
a.
A067588E22
0.458,1.448 0.365,1.688 false 0.656,1.396 0.906,1.885 true 1.969,1.417 1.844,1.781 false 2.146,1.375 2.469,1.844 true 0.823,0.073 1.531,0.281 0.708,0.208 10 false VSV is ON 2.458,0.063 3.24,0.271 0.781,0.208 10 false VSV is OFF 0.615,0.375 0.833,0.573 0.219,0.198 10 false Air 2.521,1.76 3,1.958 0.479,0.198 10 false Port E 0.958,1.802 1.438,2 0.479,0.198 10 false Port E 1.906,1.708 2.375,1.906 0.469,0.198 10 false Port F 0.219,1.729 0.688,1.927 0.469,0.198 10 false Port F 2.073,0.396 2.292,0.594 0.219,0.198 10 false Air 2.76,0.583 3.333,0.781 0.573,0.198 10 false Air Filter

Connect the GTS to the DLC3.


b.

Disconnect the vacuum hoses from the No. 1 vacuum switching valve (for swirl control valve).


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Swirl Control Valve.

Powertrain > Engine > Active Test
Tester Display
Activate the VSV for Swirl Control Valve
50004 61 43

e.

Check the VSV operation when it is operated using the GTS.

OK:
Tester Operation Specified Condition
VSV ON Air from port E flows out through port F
VSV OFF Air from port E flows out through air filter



f.

Reconnect the vacuum hoses.


Result:
Proceed to
OK
NG



OK

NG

2.INSPECT NO. 1 VACUUM SWITCHING VALVE FOR SWIRL CONTROL VALVE (RESISTANCE)
2.INSPECT NO. 1 VACUUM SWITCHING VALVE FOR SWIRL CONTROL VALVE (RESISTANCE)
a.

Inspect the No. 1 vacuum switching valve (for swirl control valve).

Click hereEngine / Hybrid System>1KD-FTV INTAKE / EXHAUST>VACUUM SWITCHING VALVE(for i-ART)>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT NO. 1 VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) (POWER SOURCE VOLTAGE)

NG

6.REPLACE VACUUM CONTROL VALVE SET
3.INSPECT NO. 1 VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) (POWER SOURCE VOLTAGE)
a.

Disconnect the No. 1 vacuum switching valve (for swirl control valve) connector.


b.
A258904C01
0.625,1.115 1.031,1.406 0.406,0.292 0.208,0.24 0.521,0.438 0.313,0.198 10 false *a 0.667,1.177 1.052,1.385 0.385,0.208 10 false C128
*a Front view of wire harness connector
(to Vacuum Switching Valve (for No. 1 Swirl Control Valve))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C128-2 - Body ground Ignition switch ON 11 to 14 V



c.

Reconnect the No. 1 vacuum switching valve (for swirl control valve) connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (NO. 1 VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) - ECM)

NG

7.CHECK HARNESS AND CONNECTOR (NO. 1 VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) - NO. 1 INTEGRATION RELAY)
4.CHECK HARNESS AND CONNECTOR (NO. 1 VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) - ECM)
a.

Disconnect the No. 1 vacuum switching valve (for swirl control valve) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance of the wire harness side connectors.

Standard Resistance:
Tester Connection Condition Specified Condition
C128-1 - C164-7 (SCV) Always Below 1 Ω
C128-1 or C164-7 (SCV) - Body ground Always 10 kΩ or higher



d.

Reconnect the No. 1 vacuum switching valve (for swirl control valve) connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE VACUUM CONTROL VALVE SET

Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CHECK HARNESS AND CONNECTOR (NO. 1 VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) - NO. 1 INTEGRATION RELAY)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the No. 1 integration relay connector.


c.

Disconnect the No. 1 vacuum switching valve (for swirl control valve) connector.


d.

Measure the resistance of the wire harness side connectors.

Standard Resistance:
Tester Connection Condition Specified Condition
1J-5 - C128-2 Always Below 1 Ω
1J-5 or C128-2 - Body ground Always 10 kΩ or higher



e.

Reinstall the No. 1 integration relay.


f.

Reconnect the No. 1 integration relay connector.


g.

Reconnect the No. 1 vacuum switching valve (for swirl control valve) connector.


Result:
Proceed to
OK
NG



OK

8.INSPECT ECM POWER SOURCE CIRCUIT

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.INSPECT ECM POWER SOURCE CIRCUIT

Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace harness or connector.


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Start the engine and wait for 3 seconds or more.


d.

2 seconds after the engine is started, race the engine for 1 second.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

f.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END