Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052110 ECD SYSTEM(for i-ART) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  P2006  Intake Manifold Runner Control Stuck Closed (Bank 1)  


DESCRIPTION

The swirl control valve is mounted on the intake manifold. The No. 1 vacuum switching valve is used to change the vacuum to control the swirl control valve.

The ECM determines the opening angle of the swirl control valve, and uses the No. 1 vacuum switching valve (for swirl control valve) to change the vacuum applied to the actuator's diaphragm to open and close the swirl control valve.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2006 Intake Manifold Runner Control Stuck Closed (Bank 1) When actual intake air volume detected by mass air flow meter continues to be smaller than volume estimated from boost pressure and intake air temperature sensor, ECM determines that swirl control valve is stuck closed (1 trip detection logic).
·

No. 1 vacuum switching valve (for swirl control valve)

·

Open or short in No. 1 vacuum switching valve (for swirl control valve) circuit

·

Intake manifold (swirl control valve)

·

Electric EGR control valve assembly

·

Turbocharger sub-assembly

·

Mass air flow meter

·

Air cleaner hose

·

Vacuum hose

·

Air cleaner element is clogged

·

Intake hose is disconnected

·

ECM


Comes on DTC stored

HINT:

*: When the above driving pattern cannot be performed due to road conditions, etc., the swirl control valve can be determined to be functioning normally if mass air flow is 84 gm/sec. or more and MAP is 105 kPa or higher when the engine speed is at 4000 rpm with no load. However, no DTCs are stored when inspecting the vehicle with this method.

The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc.

Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.


A224013C04
4.177,1.625 4.24,1.625 4.24,1.625 4.323,2.531 false 5.948,3.344 5.844,3.344 5.844,3.344 5.667,3.073 false 5.115,3.76 4.979,3.76 4.979,3.76 4.708,2.854 false 4.906,4.24 4.792,4.24 4.792,4.24 4.406,2.844 false 5.156,3.688 5.427,3.896 0.271,0.208 10 false *4 4.948,4.156 5.219,4.333 0.271,0.177 10 false *5 4.031,1.531 4.271,1.688 0.24,0.156 10 false *2 5.979,3.25 6.302,3.448 0.323,0.198 10 false *3 2.552,0.292 2.823,0.448 0.271,0.156 10 false *1
*1 ECM *2 Swirl Control Valve
*3 Vacuum Pump *4 No.1 Vacuum Switching Valve (for Swirl Control Valve)
*5 Swirl Control Valve Actuator - -


CONFIRMATION DRIVING PATTERN

P2006
DTC Detection Drive Pattern After warming up engine, drive vehicle at an engine speed of 3200 rpm or more with high load for 1 minute or more*

WIRING DIAGRAM

A276475E15
2.667,0.854 3.417,1.021 0.75,0.167 10 false EFI NO. 2 0.563,2.115 0.833,2.302 0.271,0.188 10 false EFI 0.594,3.177 1.396,3.406 0.802,0.229 10 false BATT P/I 3.083,1.167 3.292,1.344 0.208,0.177 10 false 2 2.833,1.167 3.021,1.333 0.188,0.167 10 false 1 5.313,2.146 5.802,2.333 0.49,0.188 10 false G156 5.74,2.052 6.323,2.25 0.583,0.198 10 false MREL 5.427,1.969 5.698,2.135 0.271,0.167 10 false 11 2.292,0.865 2.542,1.042 0.25,0.177 10 false 5 2.281,1.5 2.552,1.656 0.271,0.156 10 false 2 2.281,2.271 2.406,2.438 0.125,0.167 10 false 3 0.25,2.594 0.438,2.76 0.188,0.167 10 false 1 2.24,2.427 2.438,2.583 0.198,0.156 10 false 1J 2.24,1.323 2.51,1.469 0.271,0.146 10 false 1J 2.24,1.042 2.51,1.208 0.271,0.167 10 false 1J 0.406,2.604 0.677,2.76 0.271,0.156 10 false 1H 0.74,3.74 1.354,3.927 0.615,0.188 10 false Battery 6.167,3.865 6.917,4.052 0.75,0.188 10 false ECM 0.74,2.813 2.625,3.135 1.885,0.323 10 false No. 1 Integration Relay 1.25,1.646 1.896,1.833 0.646,0.188 10 false MAIN 3.5,1.49 5.5,1.854 2,0.365 10 false No. 1 Vacuum Switching Valve (for Swirl Control Valve) 3.5,1.313 3.906,1.469 0.406,0.156 10 false C128 4.708,0.927 4.958,1.125 0.25,0.198 10 false 1 3.719,0.927 3.958,1.083 0.24,0.156 10 false 2 5.323,1.042 5.781,1.354 0.458,0.313 10 false C164 5.729,1.042 6.167,1.188 0.438,0.146 10 false SCV 5.469,0.865 5.719,1.042 0.25,0.177 10 false 7 0.333,1.99 0.51,2.146 0.177,0.156 10 false 2 0.333,2.229 0.552,2.406 0.219,0.177 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P2006)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
P2006 is output A
P2006 and other DTCs are output B


HINT:

When MAP, Mass Air Flow, Intake Air, and/or Intake Air Temp (Turbo)-related DTCs are stored along with P2006, perform troubleshooting for those DTCs first.

MAP-related DTCs: P0107 and P0108 (Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>P0107).

MAF-related DTCs: P0100 (Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>P0100).

Intake Air-related DTCs: P0112 and P0113 (Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>P0112).

Intake Air Temp (Turbo)-related DTCs: P007C and P007D (Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>P007C).




A

2.CHECK AIR INTAKE SYSTEM

B

2.CHECK AIR INTAKE SYSTEM
a.

Check for air leaks and blockages between the air cleaner case and turbocharger, and between the turbocharger and intake manifold.

Result:
Result Proceed to
Leaks and/or blockages exist in the intake system A
No leaks or blockages in the intake system B


HINT:
·

Inspect the air intake system, especially hoses and pipes between the air cleaner and turbocharger.

·

Check if the air cleaner element is significantly dirty.

·

Check for abnormal disconnections, pipe and hose squashing, and any damage in the intake system.

·

Using your hand, check whether the pipes and hoses in the intake system are securely connected.

·

By applying soapy water and revving up the engine, air leaks from the intake system can be checked by checking for bubbles.

·

Check for any modifications in the intake system made by the user.





A

3.REPAIR OR REPLACE AIR INTAKE SYSTEM

B

4.CHECK INTAKE MANIFOLD (SWIRL CONTROL VALVE OPERATION)
3.REPAIR OR REPLACE AIR INTAKE SYSTEM
a.

Repair or replace the malfunctioning part in the air intake system.


Result:
Proceed to
NEXT



NEXT

18.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK INTAKE MANIFOLD (SWIRL CONTROL VALVE OPERATION)
a.
A282490C01
0.813,1.25 1.208,1.521 false 0.656,1.125 1.219,1.438 0.563,0.313 10 false *1
*1 Swirl Control Valve


Check the movement of the swirl control valve immediately after starting the engine.

OK:

Swirl control valve rod moves smoothly in the direction indicated by the arrow in the illustration.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (MAF AND MAP)

NG

8.CHECK CONNECTION OF VACUUM HOSE
5.READ VALUE USING GTS (MAF AND MAP)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Warm up the engine (engine coolant temperature is 70°C (158°F) or higher).


d.

Enter the following menus: Powertrain / Engine / Data List / MAP and MAF.

Powertrain > Engine > Data List
Tester Display
MAF
MAP
50003 61 319,314

e.

Take a snapshot when the engine speed is maintained at 4000 rpm with no load.


f.

Read the values of "MAP" and "MAF" in the Data List using the snapshot review function.

Result:
Result Proceed to
MAF 84 gm/sec or more and MAP 105 kPa or higher C
MAP below 90 kPa B
Except above A


HINT:
·

The shift lever should be in neutral and the A/C switch and all accessory switches should be off.

·

The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc.Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.





A

6.REPLACE MASS AIR FLOW METER

B

7.CHECK AND REPLACE TURBOCHARGER SUB-ASSEMBLY

C

END

6.REPLACE MASS AIR FLOW METER
a.

Replace the mass air flow meter.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>MASS AIR FLOW METER(w/ Glow Plug Controller)>REMOVAL

HINT:

If foreign matter is stuck inside the mass air flow meter, the output characteristics of the mass air flow meter may change, resulting in a malfunction.



Result:
Proceed to
NEXT



NEXT

18.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CHECK AND REPLACE TURBOCHARGER SUB-ASSEMBLY

b.

Replace the turbocharger sub-assembly.

Click hereEngine / Hybrid System>1KD-FTV INTAKE / EXHAUST>EXHAUST MANIFOLD W/ TURBOCHARGER(w/o DPF)>REMOVAL

HINT:

It is only necessary to replace the part when the results of the inspection indicate a problem.



Result:
Proceed to
NEXT



NEXT

18.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CHECK CONNECTION OF VACUUM HOSE
a.

Check the connection of the swirl control valve system vacuum hose.


Result:
Proceed to
OK
NG



OK

9.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE)

NG

16.REPAIR OR REPLACE VACUUM HOSE
9.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE)
A067588E20
0.469,1.427 0.323,1.667 false 0.667,1.313 0.917,1.802 false 1.99,1.417 1.833,1.646 false 2.177,1.292 2.5,1.76 false 0.844,0.063 1.552,0.271 0.708,0.208 10 false VSV is ON 2.458,0.083 3.24,0.292 0.781,0.208 10 false VSV is OFF 0.552,0.313 0.771,0.51 0.219,0.198 10 false Air 2.333,1.76 2.813,1.958 0.479,0.198 10 false Port E 0.74,1.792 1.219,1.99 0.479,0.198 10 false Port E 1.688,1.656 2.156,1.854 0.469,0.198 10 false Port F 0.104,1.677 0.573,1.875 0.469,0.198 10 false Port F 2,0.385 2.219,0.583 0.219,0.198 10 false Air 2.76,0.552 3.333,0.75 0.573,0.198 10 false Air Filter

a.

Disconnect the vacuum hoses from the No. 1 vacuum switching valve (for swirl control valve).


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Swirl Control Valve.

Powertrain > Engine > Active Test
Tester Display
Activate the VSV for Swirl Control Valve
50004 61 43

e.

Check the No. 1 vacuum switching valve (for swirl control valve) operation when it is operated using the GTS.

OK:
Tester Operation Specified Condition
VSV ON Air from port E flows out through port F
VSV OFF Air from port E flows out through air filter



f.

Reconnect the vacuum hoses.


Result:
Proceed to
OK
NG



OK

10.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY

NG

13.REPLACE VACUUM CONTROL VALVE SET
10.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Inspect the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1KD-FTV EMISSION CONTROL>EGR VALVE(w/ Glow Plug Controller)>INSPECTION

HINT:
·

If there are any deposits adhering to the valve, clean the valve. When cleaning the valve, use diesel fuel or kerosene.

·

When inspecting the electric EGR control valve assembly, make sure that the valve is fully closed.




Result:
Proceed to
OK
NG



OK

12.INSPECT INTAKE MANIFOLD (SWIRL CONTROL VALVE OPERATION)

NG

11.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
11.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Replace the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1KD-FTV EMISSION CONTROL>EGR VALVE(w/ Glow Plug Controller)>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.INSPECT INTAKE MANIFOLD (SWIRL CONTROL VALVE OPERATION)
12.INSPECT INTAKE MANIFOLD (SWIRL CONTROL VALVE OPERATION)
a.

Inspect the intake manifold (swirl control valve).

Click hereEngine / Hybrid System>1KD-FTV INTAKE / EXHAUST>INTAKE MANIFOLD(w/ Glow Plug Controller)>INSPECTION

HINT:
·

If there are any deposits adhering to the valve, clean the valve.

·

If there are any deposits adhering to the valve, clean the valve. When cleaning the valve, use diesel fuel or kerosene.

·

Apply vacuum to the diaphragm of the swirl control valve and check that the valve opens and closes smoothly.




Result:
Proceed to
OK
NG



OK

18.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

15.REPLACE INTAKE MANIFOLD
13.REPLACE VACUUM CONTROL VALVE SET
a.

Replace the vacuum control valve set.

Click hereEngine / Hybrid System>1KD-FTV INTAKE / EXHAUST>INTAKE MANIFOLD(w/ Glow Plug Controller)>REMOVAL

HINT:

Before replacing the vacuum control valve set, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.



Result:
Proceed to
NEXT



NEXT

14.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE)
14.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE)
a.
A067588E21
0.469,1.427 0.323,1.667 false 0.667,1.313 0.917,1.802 false 1.979,1.417 1.823,1.646 false 2.177,1.292 2.5,1.76 false 0.823,0.083 1.531,0.292 0.708,0.208 10 false VSV is ON 2.458,0.073 3.24,0.281 0.781,0.208 10 false VSV is OFF 0.552,0.313 0.771,0.51 0.219,0.198 10 false Air 2.333,1.75 2.813,1.948 0.479,0.198 10 false Port E 0.698,1.833 1.177,2.031 0.479,0.198 10 false Port E 1.646,1.646 2.115,1.844 0.469,0.198 10 false Port F 0.104,1.688 0.573,1.885 0.469,0.198 10 false Port F 2,0.385 2.219,0.583 0.219,0.198 10 false Air 2.76,0.552 3.333,0.75 0.573,0.198 10 false Air Filter

Disconnect the vacuum hoses from the No. 1 vacuum switching valve (for swirl control valve).


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Swirl Control Valve.

Powertrain > Engine > Active Test
Tester Display
Activate the VSV for Swirl Control Valve
50004 61 43

e.

Check the No. 1 vacuum switching valve (for swirl control valve) operation when it is operated using the GTS.

OK:
Tester Operation Specified Condition
VSV ON Air from port E flows out through port F
VSV OFF Air from port E flows out through air filter



f.

Reconnect the vacuum hoses.


Result:
Proceed to
OK
NG



OK

18.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

17.REPLACE ECM
15.REPLACE INTAKE MANIFOLD
a.

Result:
Proceed to
NEXT



NEXT

18.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
16.REPAIR OR REPLACE VACUUM HOSE
a.

Repair or replace the vacuum hose.


Result:
Proceed to
NEXT



NEXT

18.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
17.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

18.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
18.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Warm up the engine (engine coolant temperature is 70°C (158°F) or higher).


d.

Enter the following menus: Powertrain / Engine / Data List / MAP and MAF.

Powertrain > Engine > Data List
Tester Display
MAF
MAP
50003 61 319,314

e.

Take a snapshot when the engine speed is maintained at 4000 rpm with no load.


f.

Read the values of "MAP" and "MAF" in the Data List using the snapshot review function.

OK:

MAF is 84 gm/sec or more and MAP is 105 kPa or higher.


HINT:
·

The shift lever should be in neutral and the A/C switch and all accessory switches should be off.

·

The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc. Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.




Result:
Proceed to
NEXT



NEXT

END