Home › Engine / Hybrid System › 1KD-FTV ENGINE MECHANICAL › CYLINDER HEAD GASKET(w/ Glow Plug Controller) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009573 1KD-FTV ENGINE MECHANICAL _0052158 CYLINDER HEAD GASKET(w/ Glow Plug Controller) A

1KD-FTV ENGINE MECHANICAL  CYLINDER HEAD GASKET(w/ Glow Plug Controller)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

·

After removing the injection pipes, clean them with a brush and compressed air.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERYTERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 3.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 12.DISCONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

Hide 13.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

Hide 16.REMOVE CAMSHAFT TIMING PULLEY

a.
A060182

Remove the bolt of the camshaft timing pulley while holding the camshaft with a wrench.

NOTICE:

Make sure the timing belt is not installed when removing the bolt of the camshaft timing pulley.



b.

Remove the camshaft timing pulley.


Hide 17.REMOVE NO. 2 TIMING BELT COVER

a.

Remove the 4 bolts, nut and No. 2 timing belt cover.


Hide 18.REMOVE CYLINDER BLOCK INSULATOR

a.
A149941

Remove the cylinder block insulator from the cylinder head.


Hide 19.REMOVE CAMSHAFT

a.
A060148
0.438,0.698 0.302,1.135 0.302,1.135 0.302,1.25 true 0.208,1.292 0.396,1.469 0.188,0.177 10 false *1
*1 Key Groove


Turn the camshaft with a wrench so that the key groove of the camshaft faces upward.


b.
A060147
1.146,1.354 1.271,1.531 0.125,0.177 10 true 1 0.677,0.958 0.802,1.135 0.125,0.177 10 false 2 0.938,1.125 1.063,1.302 0.125,0.177 10 true 3 2.99,0.229 3.115,0.406 0.125,0.177 10 false 4 2.542,0.01 2.667,0.188 0.125,0.177 10 true 5 2.729,0.073 2.854,0.25 0.125,0.177 10 false 6 1.75,1.042 1.875,1.219 0.125,0.177 10 true 7 1.24,0.646 1.365,0.823 0.125,0.177 10 false 8 1.448,0.813 1.573,0.99 0.125,0.177 10 true 9 2.083,0.156 2.271,0.333 0.188,0.177 10 false 11 2.438,0.49 2.625,0.667 0.188,0.177 10 true 10 2.198,0.323 2.385,0.5 0.188,0.177 10 true 12 2.052,0.74 2.24,0.917 0.188,0.177 10 true 13 1.667,0.375 1.854,0.552 0.188,0.177 10 false 14 1.833,0.563 2.021,0.74 0.188,0.177 10 true 15

Uniformly loosen the 15 bearing cap bolts in several passes in the sequence shown in the illustration.


c.

Remove the 15 bearing cap bolts, 5 bearing caps, oil seal and 2 camshafts.


Hide 21.REMOVE CYLINDER HEAD SUB-ASSEMBLY

a.
A059194
3.042,1.75 3.177,1.938 0.135,0.188 10 false 1 2.385,1.74 2.521,1.927 0.135,0.188 10 false 9 0.5,0.26 0.635,0.448 0.135,0.188 10 false 2 3.031,0.281 3.167,0.469 0.135,0.188 10 false 3 0.49,1.74 0.625,1.927 0.135,0.188 10 false 4 2.74,0.146 2.875,0.333 0.135,0.188 10 false 5 0.792,1.865 0.927,2.052 0.135,0.188 10 false 6 2.698,1.885 2.833,2.073 0.135,0.188 10 false 7 0.823,0.146 0.958,0.333 0.135,0.188 10 false 8 1.063,0.229 1.292,0.417 0.229,0.188 10 false 10 1.698,1.75 1.927,1.938 0.229,0.188 10 false 17 1.708,0.229 1.938,0.417 0.229,0.188 10 false 18 2.344,0.229 2.573,0.417 0.229,0.188 10 false 11 1.073,1.75 1.302,1.938 0.229,0.188 10 false 12 2.052,0.156 2.281,0.344 0.229,0.188 10 false 13 1.375,1.875 1.604,2.063 0.229,0.188 10 false 14 2.01,1.875 2.24,2.063 0.229,0.188 10 false 15 1.406,0.156 1.635,0.344 0.229,0.188 10 false 16

Uniformly loosen the 18 cylinder head bolts in several passes in the sequence shown in the illustration. Then remove the 18 cylinder head bolts and 18 washers.

NOTICE:

Head warpage or cracking could result from removing bolts in the incorrect order.



b.

Remove the cylinder head from the dowels on the cylinder block and place the cylinder head on wooden blocks on a workbench.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head and cylinder block.


HINT:

If the cylinder head is difficult to remove, use a screwdriver to pry between the cylinder head and block.



Hide 22.REMOVE CYLINDER HEAD GASKET