When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
After removing the injection pipes, clean them with a brush and compressed air.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
3.REMOVE HOOD SUB-ASSEMBLY
Disconnect the washer nozzle hose.
Remove the 4 bolts and hood.
4.REMOVE NO. 1 ENGINE UNDER COVER
5.REMOVE NO. 2 ENGINE UNDER COVER
6.DRAIN ENGINE OIL
7.DRAIN ENGINE COOLANT
8.DRAIN TRANSMISSION OIL (for Manual Transmission)
9.DRAIN TRANSMISSION FLUID (for Automatic Transmission)
10.DRAIN POWER STEERING FLUID
11.REMOVE BATTERY CLAMP SUB-ASSEMBLY
Remove the bolt, nut and battery clamp.
12.REMOVE BATTERY
13.REMOVE BATTERY TRAY
14.REMOVE AIR CLEANER ASSEMBLY
15.REMOVE INTERCOOLER ASSEMBLY WITH INTAKE AIR CONNECTOR
16.REMOVE RADIATOR ASSEMBLY
17.REMOVE STARTER ASSEMBLY
for Denso Made: (See page Engine / Hybrid System>1KD-FTV STARTING>STARTER(for DENSO Made)>REMOVAL)
for Bosch Made: (See page Engine / Hybrid System>1KD-FTV STARTING>STARTER(for BOSCH Made)>REMOVAL)
18.REMOVE FRONT EXHAUST PIPE ASSEMBLY
w/ DPF: (See page Engine / Hybrid System>1KD-FTV INTAKE / EXHAUST>EXHAUST PIPE(w/ DPF)>REMOVAL)
w/o DPF: (See page Engine / Hybrid System>1KD-FTV INTAKE / EXHAUST>EXHAUST PIPE(w/o DPF)>REMOVAL)
19.REMOVE FRONT PROPELLER SHAFT ASSEMBLY
20.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
21.DISCONNECT HEATER HOSE
Disconnect the 2 heater hoses.
22.DISCONNECT PRESSURE FEED TUBE ASSEMBLY
Disconnect the oil reservoir to pump hose.
Disconnect the pressure feed tube.
23.DISCONNECT FUEL HOSE
Disconnect the 2 fuel hoses.
24.DISCONNECT UNION TO CONNECTOR TUBE HOSE
Disconnect the union to connector tube hose.
25.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
26.DISCONNECT WIRE HARNESS
Remove the upper relay block cover.
Remove the side relay block cover.
Remove the nut and disconnect the engine room junction block wire.
Disconnect the 2 engine room junction block connectors.
Remove the bolt and disconnect the ground cable.
Remove the 2 nuts, detach the clamp and disconnect the wire harness.
Disconnect the 4 glow plug controller connectors.
Disconnect the 4 injector driver connectors.
Disconnect the 4WD control ECU connector.
for Automatic Transmission:
Disconnect the 3 TCM connectors.
Disconnect the 6 ECM connectors.
27.DISCONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)
Remove the 4 bolts and disconnect the cooler compressor.
It is not necessary to completely remove the cooler compressor. With the hoses connected to the cooler compressor, hang the cooler compressor on the vehicle body with a rope.
28.REMOVE MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)
29.REMOVE DRIVE PLATE AND TORQUECONVERTER SETTING BOLT (for Automatic Transmission)
30.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
31.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the rear No. 1 engine mounting insulator is necessary.
Remove the 4 bolts and rear No. 1 engine mounting insulator.
32.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)
33.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)
34.REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)
Using SST, hold the crankshaft pulley.
Remove the 8 bolts and flywheel.
35.REMOVE PUMP IMPELLER DRIVE PLATE (for Automatic Transmission)
Using SST, hold the crankshaft pulley.
Remove the 8 bolts, rear drive plate spacer, pump impeller drive plate, and flywheel.
36.REMOVE REAR END PLATE
Remove the bolt and rear end plate.
37.INSTALL ENGINE HANGERS
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
Install a No. 1 engine hanger and No. 2 engine hanger with 2 bolts as shown in the illustration.
Part No.
| No. 1 Engine Hanger | 12284-30020 |
| No. 2 Engine Hanger | 12282-67030 |
| Bolt | 91552-81014 and 91642-81030 |
Install the engine hangers with new bolts.
38.REMOVE ENGINE ASSEMBLY
Attach an engine sling device and hang the engine with a chain block.
Remove the 4 bolts and 4 nuts.
Remove the engine by operating the engine sling device and chain block.
39.INSTALL ENGINE TO ENGINE STAND
Install the engine to an engine stand with bolts.
Remove the 2 bolts and 2 engine hangers.
40.REMOVE ENGINE WIRE
Remove the engine wire from the engine.
41.REMOVE FRONT ENGINE MOUNTING INSULATOR
| *A | RH Side |
| *B | LH Side |
Remove the 2 nuts and 2 front engine mounting insulators.