Home › Engine / Hybrid System › 2KD-FTV ENGINE MECHANICAL › ENGINE UNIT(w/o DPF)
RM1840EF _51 Engine / Hybrid System _009574 2KD-FTV ENGINE MECHANICAL _0052172 ENGINE UNIT(w/o DPF) A

2KD-FTV ENGINE MECHANICAL  ENGINE UNIT(w/o DPF)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

·

After removing the injection pipes, clean them with a brush and compressed air.



PROCEDURE

Hide 1.INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH

a.

Install the front No. 1 engine mounting bracket with the 4 bolts.

Torque:
68 N*m (693 kgf*cm, 50 ft.*lbf)


Hide 2.INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH

a.

Install the front No. 1 engine mounting bracket with the 4 bolts.

Torque:
68 N*m (693 kgf*cm, 50 ft.*lbf)


Hide 6.INSTALL VANE PUMP ASSEMBLY

a.

Install a new O-ring to the vane pump.


b.

Install the vane pump with the 2 nuts.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)


Hide 7.INSTALL VACUUM PUMP ASSEMBLY

a.

Install 2 new O-rings to the vacuum pump.


b.

Install the vacuum pump with the 2 nuts.

Torque:
21 N*m (210 kgf*cm, 15 ft.*lbf)


Hide 8.INSTALL TIMING GEAR COVER INSULATOR (w/ EGR Cooler)

a.

Install the gear cover insulator with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 15.INSTALL NO. 2 EGR HOLE COVER PLATE (w/o EGR System)

a.

Install a new gasket and the No. 2 EGR hole cover plate with the 2 nuts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 18.INSTALL WATER OUTLET

a.
A098977
2.625,1.479 2.844,0.917 2.844,0.917 2.906,0.917 false 2.948,0.813 3.125,0.99 0.177,0.177 10 false *1
*1 Claw


Install a new gasket to the cylinder head as shown in the illustration.

HINT:

Make sure the claws of the gasket face the water outlet.



b.

Install the water outlet with the 2 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 21.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET

a.

Install the No. 1 compressor mounting bracket with the 4 bolts.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


Hide 22.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

a.
A303111
0.563,1.354 0.313,1.865 0.313,1.865 0.313,2.021 true 1.156,0.677 1.875,0.333 1.875,0.333 2.042,0.333 true 2.167,0.25 2.479,0.448 0.313,0.198 10 false *1 0.229,2.073 0.542,2.271 0.313,0.198 10 false *2 0.792,0.427 0.979,0.635 0.188,0.208 10 true A 1.021,1.021 1.208,1.229 0.188,0.208 10 true A
*1 Cylinder Block
*2 V-ribbed Belt Tensioner


Install the V-ribbed belt tensioner with the 4 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

HINT:

Firmly press and hold the V-ribbed belt tensioner against the cylinder block to eliminate any gaps in the areas labeled A in the illustration. Then uniformly tighten the 4 bolts.



Hide 23.INSTALL GENERATOR BRACKET

a.

Install the generator bracket with the bolt.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 26.INSTALL VENTILATION HOSE HEAT INSULATOR (w/o EGR Cooler)

a.

Install the ventilation hose heat insulator with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 28.INSTALL INTERCOOLER SUPPORT BRACKET (w/ EGR Cooler)

a.

Install the intercooler support bracket with the 2 bolts.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


Hide 29.INSTALL NO. 2 INTERCOOLER SUPPORT BRACKET (w/ EGR Cooler)

a.

Install the No. 2 intercooler support bracket with the 2 bolts.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)