Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009577 1GR-FE ENGINE MECHANICAL _0052210 ENGINE ASSEMBLY A

1GR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 2.REMOVE ENGINE FROM ENGINE STAND

a.

Attach an engine sling device and hang the engine with a chain block


b.

Lift the engine and remove it from the engine stand.

NOTICE:
·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.

·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.




Hide 3.INSTALL ENGINE ASSEMBLY

a.

Slowly lower the engine into the engine compartment.


b.

Install the engine mounting brackets to the frame with the 4 bolts and 4 nuts.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


c.

Remove the 2 engine hangers and 4 bolts.


Hide 5.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

a.

Install the rear No. 1 engine mounting insulator to the automatic transmission with the 4 bolts.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


Hide 12.INSTALL FRONT FENDER APRON SEAL UPPER

a.

Install the RH and LH fender apron seals with the 10 clips.


Hide 13.INSTALL FRONT FENDER SEAL

a.

Install the RH and LH fender seals with the 10 clips.


Hide 16.INSTALL BATTERY

Hide 17.INSTALL NO. 2 ENGINE WIRE

a.

Connect the No. 2 engine wire to the cylinder block with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 18.INSTALL ENGINE WIRE

a.

Connect the 2 engine room junction block connectors and attach the wire clamp.


b.

Connect the cable to the engine room junction block with the nut.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


c.

Attach the 4 claws to install the side relay block cover.


d.

Install the upper relay block cover.


e.
A252953
0.781,2.229 0.979,2.427 0.198,0.198 10 false *a 1.333,3.146 1.563,3.313 0.229,0.167 10 true 45° 0.521,0.271 0.792,0.438 0.271,0.167 10 false 45° 1.063,0.281 1.333,0.448 0.271,0.167 10 false 45°
*a Frame Side


Connect the ground wire with the bolt and clamp.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


f.

Connect the ground wire to the frame with the bolt so that it is within the range shown in the illustration.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


g.

Push the engine wire through the dash panel into the cabin. The wire should be within the range shown in the illustration.


h.

Connect the differential actuator connector.


i.

Connect the ECM connectors.

i.

Connect the 4 ECM connectors.


ii.

Connect the 4 wheel drive control ECU connector.


iii.


j.

Attach the wire clamp to the front No. 1 engine mounting bracket LH with the bolt.

Torque:
13 N*m (128 kgf*cm, 9 ft.*lbf)


Hide 20.INSTALL HEATER WATER HOSE

a.

Connect the heater water inlet hose.


b.

Connect the heater water outlet hose.


Hide 21.CONNECT NO. 2 FUEL PIPE SUB-ASSEMBLY

Hide 22.CONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 24.INSTALL VANE PUMP ASSEMBLY

a.

Install the vane pump with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:

Do not hit other parts with the pulley when installing the vane pump.



b.

Connect the power steering oil pressure switch connector.


Hide 29.CONNECT RADIATOR HOSE INLET

Hide 30.CONNECT RADIATOR HOSE OUTLET

Hide 31.INSTALL RADIATOR SIDE DEFLECTOR RH

Hide 32.INSTALL RADIATOR SIDE DEFLECTOR LH

Hide 33.INSTALL NO. 2 AIR CLEANER HOSE

a.

Install the No. 2 air cleaner hose with the 2 bolts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 37.INSTALL HOOD SUB-ASSEMBLY

a.

Install the hood with the 4 bolts and adjust the hood to the correct position.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


b.

Connect the washer nozzle hose.


Hide 38.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 47.INSTALL NO. 1 ENGINE UNDER COVER

Hide 48.INSTALL ENGINE SIDE COVER SUB-ASSEMBLY LH

Hide 49.INSTALL ENGINE SIDE COVER SUB-ASSEMBLY RH